Latest public opinion service Tenders | Government public opinion service Tenders

CTN :45696125

13 Jul, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using driving and dr

State Government

CTN :45669079

08 Jul, 2026 7.24 Lacs

Amreli - Gujarat

Tender For installation of various instruments and monitoring system at vadi irrigation scheme - supplying, installing, testing, and commissioning of a v-notch weir mechanical flow measuring device) for measuring low flow seepage in dams. the device shall have a notch angle of 22.5°, 45°, 60°, or 90° depending on discharge range, a stainless steel ss-304 / ss-316 plate with thickness of 3–5 mm, and be suitable for measurement ranges of approximately 0–50 l/s depending on notch angle. the weir shall have ±1% full-scale reading accuracy, operate under 5–100% humidity, temperature −20°c to +60°c, and provide corrosion protection through anti-corrosion finish. complete in all respects as directed by the engineer-in-charge.with different sizes mentioned below: (1) 90° vnotch- 20 x 40 secticin 15 lit/sec, providing, installing and commissioning permanent ground control point (gcp) settlemnt marker comprising ms base plate (250×250×5 mm conforming to is 2062), gi riser pipe 25 mm dia (medium class as per is 1239), sand filling (clean river sand, loose), optional pvc/gi outer casing (min 100 mm dia), precast concrete cover (m20, 500×500×50 mm with central hole), ms/gi reference cap, and painting in black & white checkerboard pattern using weather-resistant enamel paint, complete with excavation, installation, alignment, and all materials, labour, tools, and accessories, suitable for survey works using total station / drone survey, complete as per specifications and direction of engineer-in-charge., providing & laying in position 'nominal mix' cement concrete using cement sand and crushed aggregate by machine mix incl. necessary formworks ,centering ,scaffolding compaction by mechanical vibrator curing as directed with all lead & lift etc (c) concrete grade 1:2:4 and msa-40mm(graded))

State Government

CTN :45669080

08 Jul, 2026 5.38 Lacs

Amreli - Gujarat

Tender For installation of various instruments and monitoring system at thebi irrigation scheme - supplying, installing, testing, and commissioning of a v-notch weir (mechanical flow measuring device) for measuring low flow seepage in dams. the device shall have a notch angle of 22.5°, 45°, 60°, or 90° depending on discharge range, a stainless steel ss-304 / ss-316 plate with thickness of 3–5 mm, and be suitable for measurement ranges of approximately 0–50 l/s depending on notch angle. the weir shall have ±1% full-scale reading accuracy, operate under 5–100% humidity, temperature −20°c to +60°c, and provide corrosion protection through anti-corrosion finish. complete in all respects as directed by the engineer-in-charge.with different sizes mentioned below: (1) 90° vnotch- 20 x 40 secticin 15 lit/sec, providing, installing and commissioning permanent ground control point (gcp) settlemnt marker comprising ms base plate (250×250×5 mm conforming to is 2062), gi riser pipe 25 mm dia (medium class as per is 1239), sand filling (clean river sand, loose), optional pvc/gi outer casing (min 100 mm dia), precast concrete cover (m20, 500×500×50 mm with central hole), ms/gi reference cap, and painting in black & white checkerboard pattern using weather-resistant enamel paint, complete with excavation, installation, alignment, and all materials, labour, tools, and accessories, suitable for survey works using total station / drone survey, complete as per specifications and direction of engineer-in-charge., providing & laying in position 'nominal mix' cement concrete using cement sand and crushed aggregate by machine mix incl. necessary formworks ,centering ,scaffolding compaction by mechanical vibrator curing as directed with all lead & lift etc (c) concrete grade 1:2:4 and msa-40mm(graded))

State Government

CTN :45675246

07 Jul, 2026 5.87 Lacs

Amreli - Gujarat

Tender For installation of various instruments at raidy & dhataravdi-1 irrigation scheme - item no.1:- providing, supplying, installing, testing, and commissioning of a v-notch weir (mechanical flow measuring device) for measuring low flow seepage in dams. the device shall have a notch angle of 22.5°, 45°, 60°, or 90° depending on discharge range, a stainless steel ss- 304/ss-316 plate with thickness of 3-5 mm, and be suitable for measurement ranges of approximately 0-50 l/s depending on notch angle. the weir shall have ±1% fullscale reading accuracy, operate under 5-100% humidity, temperature -20°c to +60°c, and provide corrosion protection through anti-corrosion finish. complete in all respects as directed by the engineer-in-charge. (1) 90° v-notch-20 x 40 secticin 15 lit/sec , item no.2:- providing, installing and commissioning permanent ground control point (gcp) settlemnt marker comprising ms base plate (250×250×5 mm conforming to is 2062), gi riser pipe 25 mm dia (medium class as per is 1239), sand filling (clean river sand, loose), optional pvc/gi outer casing (min 100 mm dia), precast concrete cover (m20, 500×500×50 mm with central hole), ms/gi reference cap, and painting in black & white checkerboard pattern using weather-resistant enamel paint, complete with excavation, installation, alignment, and all materials, labour, tools, and accessories, suitable for survey works using total station / drone survey, complete as per specifications and direction of engineer-in-charge. , item no.3:- providing & laying in position 'nominal mix' cement concrete using cement sand and crushed aggregate by machine mix incl. necessary formworks, centering, scaffolding compaction by mechanical vibrator curing as directed with all lead & lift etc. (c ) concrete grade 1:2:4 and msa-40 mm(graded)

Central Government/Public Sector

CTN :45561586

23 Jun, 2026 NA

Multi City - Maharashtra

Tender For auction sale of depot ferrous scrap - scrap and unserviceable condemned mix m.s. coach cutting items & various types of similar items such as , body side door m.s., p.o.h. coaches realised corroded pieces,air brake,clamp,pipe pin,m.s. door of battery box ,m.s.ventilation door,foot plate,ice box,m.s. spring,m.s. angle,and m.s. lader with rubber coating,coach cuttings, coach doors , seat frames , bearth/seat frames, light head stock cuttings, train lighting fittings,, side lamps lamp hand signal, fittings, tail lamp fittings, cft/tl light fittings, ictp/ icfp empty swich boxes tail lamps, tube light fittings, tube light jali, fan blades, fan jali, fan guards fan ribs, fan rings, empty power pannels, signal platform, destination board, valley board, letter board,ms signal base, loc, inercooler, nut bolts and other hardwares, m s furniture.m s wheel stand,window grill, ms measuring cans, tins, racks, break pipes, silencer of tower wagon, dust bin, ms pipe and cut pcs. of ms pipes, rods, ms bars released from broken constructin, compressor spring, wire /coil springs, ms rope wire, pcs. of brake beam pipes, stands, m s ferrous light junk kachra related scrap i.e ms angles, chanels, flats pcs. of cable racks/laders ms brackets, dust bin stand, tin fuse box, fire extinguisher, empty glow sign boards, empty electrical pannel, ms stand, oven, earthing patti, empty cable tray, fly catcher, galvanized patra / sheet and their cut offs, cut pieces of ms cupboards, rack etc, plain/ corrugated / toughened sheets and its cut pcs. such as strips, patties, patties, patra, rings, coils, boxes, ms brake control cover, patra, angle, small springs, pins, wire, electric point, shunt signal unit and post. signal ladder , location box, earth electrode , signal post and base , signal unit, point roddings , junction route indicator and cut pieces in mijscellaneous, coil, collapsible doors and shutters and their parts/cut offs, grills , channel grills, compound /bridge jali with or without frame, ms fencing and their parts, fencing patties, angle pcs., frames,wire mesh, g.i./ms pipes and tubes , tubes and their cut pcs, damaged gi/ ms pipes/ rods/ tubes and their pcs. , ms/galvanised boxes, junction box, switch boxes, empty convertor, payary (steps), filters, rings, nut bolts, u clips, pipe pin, gate m/c dismentled, liquid container, damaged video boxes and their cut offs, crt cabinet, location boxes , jumper, jumper box,ground connections , basket steel, water cane/ material carring trolley,steel baskets, containers, trays, frames, stretchers, nets/ jali , released ground connection, halogen, panto pans, compressor spares, dust guard, air filters and filter covers, ms/gi duct and its parts,insulating armature of signal cable, hand lamps, side lamps, signal lamps petromax, hs lamp, clamps, signal post,signal platform, signal base, ms/ gi wire/ coil, funnels, wall protectors, boxes, iron bar pcs released from broken construction , desmantelled weighing machines parts/ covers etc. ms pipe with or without ci attachment, bins, plates, rings, spares/ parts /body of weighing machine , platform weighing machine and its parts, pressure switches and other switches , signal parts, location boxes,panel board,fuse box,mdb board,pedestial for lc gate and their cut parts and other ferrous miscellaneous scrap items with or without minor nf/ss/ wooden / rubber / rexine attachments of sorts and sizes, broken and damaged, u/s for rly. use, excluding items: rail and rail pcs., axles and axle pcs., wheel tyre and pcs., cam shafts, helical springs, bolster springs, buffer plungers, face plates, axle box housings/ casings, brake beams, fish plates, screw couplings/draw bar hooks, break beams, reservoir tanks, st sleepers and other various types of similar ms items etc. note: 1. hammering/ pressing/ cutting is permitted for easy loading only, 2. if found any non-ferrous item will not be delivered (qty approx)

Central Government/Public Sector

CTN :45561588

23 Jun, 2026 NA

Multi City - Maharashtra

Tender For auction sale of depot ferrous scrap - scrap and unserviceable condemned mix m.s. coach cutting items & various types of similar items such as , body side door m.s., p.o.h. coaches realised corroded pieces,air brake,clamp,pipe pin,m.s. door of battery box ,m.s.ventilation door,foot plate,ice box,m.s. spring,m.s. angle,and m.s. lader with rubber coating,coach cuttings, coach doors , seat frames , bearth/seat frames, light head stock cuttings, train lighting fittings,, side lamps lamp hand signal, fittings, tail lamp fittings, cft/tl light fittings, ictp/ icfp empty swich boxes tail lamps, tube light fittings, tube light jali, fan blades, fan jali, fan guards fan ribs, fan rings, empty power pannels, signal platform, destination board, valley board, letter board,ms signal base, loc, inercooler, nut bolts and other hardwares, m s furniture.m s wheel stand,window grill, ms measuring cans, tins, racks, break pipes, silencer of tower wagon, dust bin, ms pipe and cut pcs. of ms pipes, rods, ms bars released from broken constructin, compressor spring, wire /coil springs, ms rope wire, pcs. of brake beam pipes, stands, m s ferrous light junk kachra related scrap i.e ms angles, chanels, flats pcs. of cable racks/laders ms brackets, dust bin stand, tin fuse box, fire extinguisher, empty glow sign boards, empty electrical pannel, ms stand, oven, earthing patti, empty cable tray, fly catcher, galvanized patra / sheet and their cut offs, cut pieces of ms cupboards, rack etc, plain/ corrugated / toughened sheets and its cut pcs. such as strips, patties, patties, patra, rings, coils, boxes, ms brake control cover, patra, angle, small springs, pins, wire, electric point, shunt signal unit and post. signal ladder , location box, earth electrode , signal post and base , signal unit, point roddings , junction route indicator and cut pieces in mijscellaneous, coil, collapsible doors and shutters and their parts/cut offs, grills , channel grills, compound /bridge jali with or without frame, ms fencing and their parts, fencing patties, angle pcs., frames,wire mesh, g.i./ms pipes and tubes , tubes and their cut pcs, damaged gi/ ms pipes/ rods/ tubes and their pcs. , ms/galvanised boxes, junction box, switch boxes, empty convertor, payary (steps), filters, rings, nut bolts, u clips, pipe pin, gate m/c dismentled, liquid container, damaged video boxes and their cut offs, crt cabinet, location boxes , jumper, jumper box,ground connections , basket steel, water cane/ material carring trolley,steel baskets, containers, trays, frames, stretchers, nets/ jali , released ground connection, halogen, panto pans, compressor spares, dust guard, air filters and filter covers, ms/gi duct and its parts,insulating armature of signal cable, hand lamps, side lamps, signal lamps petromax, hs lamp, clamps, signal post,signal platform, signal base, ms/ gi wire/ coil, funnels, wall protectors, boxes, iron bar pcs released from broken construction , desmantelled weighing machines parts/ covers etc. ms pipe with or without ci attachment, bins, plates, rings, spares/ parts /body of weighing machine , platform weighing machine and its parts, pressure switches and other switches , signal parts, location boxes,panel board,fuse box,mdb board,pedestial for lc gate and their cut parts and other ferrous miscellaneous scrap items with or without minor nf/ss/ wooden / rubber / rexine attachments of sorts and sizes, broken and damaged, u/s for rly. use, excluding items: rail and rail pcs., axles and axle pcs., wheel tyre and pcs., cam shafts, helical springs, bolster springs, buffer plungers, face plates, axle box housings/ casings, brake beams, fish plates, screw couplings/draw bar hooks, break beams, reservoir tanks, st sleepers and other various types of similar ms items etc. note: 1. hammering/ pressing/ cutting is permitted for easy loading only, 2. if found any non-ferrous item will not be delivered (qty approx)

CTN :45384476

17 Jun, 2026 NA

Dharmapuri - Tamil Nadu

Tender For corrigendum : purchase of equipments for mechanical department - purchase of equipments for mechanical department, tail stock assembly medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, working model of fuel supply system - petrol mpfi type petrol multi point fuel injection (mpfi) system for dismantling and assembly practice system type: non-working / cut-section model for study of internal construction construction: actual automotive components or equivalent training model mounted on frame includes throttle body (sectioned), fuel injectors, fuel rail, intake manifold includes fuel pump, fuel tank (dummy), fuel filter, pressure regulator includes ignition system components: ignition coil, spark plug, distributor (if applicable) ecu module (dummy/display type) with wiring layout representation all components cut-open, painted, and clearly labelled provision for manual demonstration of flow path and component interaction mounted on rigid ms powder-coated frame designed for repeated dismantling, assembly, and component identification, hydraulic cylinderbore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply: mounted on training base suitable for dismantling and inspection, hydraulic operated directional control valves (dcv) type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study, bearing with shaft assembly type: dismantling and assembly teaching unit shaft diameter: 30 mm shaft material: en8 steel bearings: deep groove ball bearing (6205 / 6206) housing: cast iron locking arrangement: circlips end covers mounting: bench-mounted / frame mounted unit, coupling unit using driving and driven shafts using plummer block bearing unit the plummer block housing material: cast iron (grade fg 200 or equivalent). type: sng or snl series (split-type housing). sealing: felt seals or v-ring seals (to demonstrate lubrication retention). lubrication: provided with a grease nipple at the top center for manual lubrication practice. the bearing type: self-aligning ball bearing (1200 series) or spherical roller bearing (22200 series). bore diameter: standard 25mm or 30 mm. shafting and coupling shaft material: ground carbon steel (en8 or en9) for high surface finish. coupling type: flexible coupling: to demonstrate the bearings ability to handle slight misalignment. rigid flange coupling: to demonstrate traditional direct connection. driving/driven setup: one shaft connected to a small electric motor (driving) and the other to a brake drum or load (driven)., 3d printing machine build volume(wxdxh) 256 x 256 x 256 mm shell enclosed (plastic & glass) hot end all-metal nozzle 0.4 mm stainless steel included max hot end temperature 300 nozzle diameter 0.4 mm (included) 0.2 mm, 0.6 mm, 0.8 mm build plate compatibility textured pei plate, cool plate, engineering plate, high temperature plate max build plate temperature 100 max speed of tool head 500 mm/s max acceleration of tool head 20 m/s supported filament pla, petg, tpu, pva, pet, abs, asa chamber monitoring camera low rate camera 1280 x 720/0.5fps time lapse supported filament run out sensor :yes control board fan closed loop control auxiliary part cooling fan closed loop control air filter activated carbon filter

State Government

CTN :45300981

17 Jun, 2026 5.67 Crore

Wardha - Maharashtra

Tender For corrigendum : supplying of furniture to newly formed cgrf office, for jr. law officer and mini training centre under o&m circle wardha tq. dist. wardha.-providing, supplying and placing of godrej make beat fabric high back 1.00chair with head rest. seat/back assembly: the seat & back is made up of1.2 ± 0.1cm thk. hot pressed plywood measured. upholstered with knittedfabric , over moulded high resilience polyurethane foam high back size:51.8 cm. (w) x 75.2 cm. (h) seat size : 49.0 cm. (w) x 48.8 cm. (d) highresilience (hr) polyurethane foam: the hr polyurethane foam ismoulded with density = 55+/-2 kg/m³ and hardness 16 ± 2 kgf as per is:7888for 25% compression. armrests: the adjustable armrest is designed with thefollowing features: • up-down adjustment– 8 steps (8.0±0.5 cm range) • heightadjustable armrest structure which is powder coated & fitted with an armresttop. • fixed armrest top is pu moulded over metal insert. front pivotsynchro mechanism: the adjustable tilting mechanism is designed with thefollowing features360° revolving type. • single point control. • front-pivot fortilt with feet resting on ground ensuring more comfort. • tilt tensionadjustment. • 4-position locking with anti-shock feature. • seat/back tiltingratio of 1:2 . back height adjustability: back can be adjusted in 5 positionsby manually. stroke of height adjustable spine is 7 cm. back height adjustabilityis applicable for high back and mid back chair. pneumatic heightadjustment: the pneumatic height adjustment has an adjustment stroke of10.0 ± 0.3 cm. pedestal assembly with castors: the pedestal is injectionmoulded in black 30% glass-filled nylon and fitted with 5 nos. twin wheelcastors. the pedestal pitch-centre dia is ø66.1 ± 0.5 cm. (76.1 ± 1.0 cm. withcastors) . twin wheel castors: the twin wheel castors are injectionmoulded in black nylon. option of sliding seat mechanism: seat can beslide horizontally as per user convenience. stroke of seat slide is 5 cm. thisoption is available for revolving pedestal type of chair. overall dimensions ofchair seat height - min 45.0 to max 55.0cm. height - min 102.0 to max 119.0cm. width & depth of chair as measured from p

CTN :45404122

19 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For corrigendum : supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using

Central Government/Public Sector

CTN :45401041

09 Jun, 2026 NA

Multi City - Tamil Nadu

Tender For auction sale of depot ferrous scrap - pl no.98097027 condemned and unserviceable ferrous c.i.scrap consisting of released p.way and signal materials such as sej chair,signal point machine body , signal aspect, offset bracket,ct box,e/hp type locks, signal post base, signal lever frame arrangements, control terminal boxes (ctb), cylindrical weight, gate boom weight, l.c gate support,boom lock ground lever,heel block, a base,c i beam,pulleys,trestle and released under ground water pipes - broken into small pieces and dismantled weigh machines with/without parts and fittings and c.i bearing plates, cst 9 plate, slide chair, c.i. pots, c.i. blocks, distant blocks, d bracket, and other similar items of c.i. in nature.all the above items are of sorts and sizes, full/part, damaged/broken, with/without m.s attachments. note: (1) crane loading permitted (2) n.f. attachments,if any, should be removed and handed over to the rlys.

Public Opinion Service Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

State Government

State Government

Central Government/Public Sector

Central Government/Public Sector

State Government

Central Government/Public Sector