Get complete information related to latest Pump Oil Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Pump Oil Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Pump Oil Tenders.
Tender For supply of inhibited mineral insulating oil shall conforming to is:335/2018 and railways requirem e nt as per rdso letter no. ti/ psi/ insoil/ policy/19/01-18 dated 26.07.2019 with additional require ments as under:- 1) lowest cold start energizing temperature - 0 degree c; 2) presence of oxidation i nhibitor (dbpc-2, 6 ditertiary butyl-para-cresol) content range - 0.25%-0.30%, 3) oxidation stability: (a) total acidity (neutralization value after oxidation (max) 0.2mg koh/gm (b) total sludge after oxid ation (max) 0.05% by mass. packing:- pack (a} transformer oil shall be supplied in new non-returna ble quality grade b, type-i mild steel drums of 210 litres nominal capacity conforming to is:1783 (part ii/88 with amdt no.1. the drums shall be got pre-inspected before filling.alternatively isi marked drum s will be acceptable without pre-inspection. drg/specification:-spec. no is:335(2018) railways require ment as per rdso letter no. ti/psi/insoil/policy/19 dt-26.07.2019 [ warranty period: 30 months af ter the date of delivery ]
Tender For supply of diffusion pumpoil hivac , high alumina hearth support insulator , moly grooved strip heater , high alumina female insulator for heater support , high alumina male insulator for heater support , moly washer , copper feedthrough insulators , nylon spacer , nylon insulator , moly connecting rod for copper feedthrough , molybdenum heater connecting square block , molybdenum heater connecting holding block , copper feedthrough for feed through assembly , 8mm viton o ring , 10 hp kdi water circulation pump , 7 point 5 hp kdi water circulation pump , programming temperature controller , pressure transmitter , water pressure switch type ip 100 , 1 by 2 inch non return valve for gas manifold , 1 by 2 inch ball valve for gas manifold , complete set of viton o rings except for vacuum pumps , 1 inch carbon free hose pipe-10 mtr long , 3 by 4 inch carbon free hose pipe-10 mtr long , qsv-1 inch manually operated butterfly valve ss with both side kf 25 clamp and viton o ring , gas manifold 2 stage gas regulators , final line regulator flr , kf fittings and accessories , hhv make right angle valve model rpv-25 , rigid r type thermocouple , molybdenum plate , digital panel voltmeter 12 24 v dc , digital panel ammeter dc 10amps 20amps , on - off switch , 1 by 4 inch speed control mufflers , rotary pumpoil md 504 , pneumatics pipelines with accessories , water pipe lines withaccessories , heat exchanger fixing , r type flexible thermocouple 0 point 5 dia 1.5 mtrs long
Tender For corrigendum : supply of drive end for drive end assembly of ammonia or hydrazine dosing pump , retainer for drive end assembly of ammonia or hydrazine dosing pump , stroke length controller for drive end assembly of ammonia or hydrazine dosing pump , control housing for drive end assembly of ammonia or hydrazine dosing pump , stroke length adjuster for drive end assembly of ammonia or hydrazine dosing pump , lock retainer for drive end assembly of ammonia or hydrazine dosing pump , lock nut for retainer for drive end assembly of ammonia or hydrazine dosing pump , digit counter assembly for drive end assembly of ammonia or hydrazine dosing pump , hex hd screw m6 x 16 for drive end assembly of ammonia or hydrazine dosing pump , hex hd screw m6 x 25 for drive end assembly of ammonia or hydrazine dosing pump , hex hd screw m8 x 20 for drive end assembly of ammonia or hydrazine dosing pump , hex hd screw m8 x 25 for drive end assembly of ammonia or hydrazine dosing pump , hex hd screw m10 x 30 for drive end assembly of ammonia or hydrazine dosing pump , cap screw m5 x 10 for drive end assembly of ammonia or hydrazine dosing pump , cap screw m5 x 16 for drive end assembly of ammonia or hydrazine dosing pump , cap screw m10 x 16 for drive end assembly of ammonia or hydrazine dosing pump , grub screw m5 x 10 for drive end assembly of ammonia or hydrazine dosing pump , lock nut m6 for drive end assembly of ammonia or hydrazine dosing pump , oil filler 0.25 inch bsp for drive end assembly of ammonia or hydrazine dosing pump , drain plug 0.25 inch bsp for drive end assembly of ammonia or hydrazine dosing pump , spring dowel pin for drive end assembly of ammonia or hydrazine dosing pump , internal circlip b38 for drive end assembly of ammonia or hydrazine dosing pump , external circlip a10 for drive end assembly of ammonia or hydrazine dosing pump , oil seal 38 x 19 x 10 for drive end assembly of ammonia or hydrazine dosing pump , oil seal 50 x 34 x 9 for drive end assembly of ammonia or hydrazine dosing pump , washer spring and punched m6 for drive end assembly of ammonia or hydrazine dosing pump , washer spring and punched m8 for drive end assembly of ammonia or hydrazine dosing pump , washer spring and punched m10 for drive end assembly of ammonia or hydrazine dosing pump , m5 copper washer for drive end assembly of ammonia or hydrazine dosing pump , parallel key 5 x 5 x 32 for drive end assembly of ammonia or hydrazine dosing pump , o ring 50.49 x 2.62 for drive end assembly of ammonia or hydrazine dosing pump , o ring 47.35 x 1.78 for drive end assembly of ammonia or hydrazine dosing pump , o ring 47.22 x 3.53 for drive end assembly of ammonia or hydrazine dosing pump , oil level indicator for drive end assembly of ammonia or hydrazine dosing pump , coupling set for drive end assembly of ammonia or hydrazine dosing pump , gasket set for liquid end assembly of ammonia or hydrazine dosing pump , sandwich ring for liquid end assembly of ammonia or hydrazine dosing pump , vacuum system for liquid end assembly of ammonia or hydrazine dosing pump , prv and air bleed assembly for liquid end assembly of ammonia or hydrazine dosing pump , refill system for liquid end assembly of ammonia or hydrazine dosing pump , actuator body for liquid end assembly of ammonia or hydrazine dosing pump , hyd chember for liquid end assembly of ammonia or hydrazine dosing pump , plunger //bid details 2 / 79 guide for liquid end assembly of ammonia or hydrazine dosing pump , cover for oil chember for liquid end assembly of ammonia or hydrazine dosing pump , plunger for liquid end assembly of ammonia or hydrazine dosing pump , diaphragm head for liquid end assembly of ammonia or hydrazine dosing pump , air bleed nipple for liquid end assembly of ammonia or hydrazine dosing pump , imported diaphragm set for liquid end assembly of ammonia or hydrazine dosing pump , valve cage for liquid end assembly of ammonia or hydrazine dosing pump , valve seat for liquid end as
Tender For requirement of safety, rescue & security items for ssctps fy 2025-26,suratgarh - head up light with alkaline batteries with adjustable cloth stripper for head and rubber strap , gum boots with steel toe cap moulded pvc to protect against oil acid and alkalie resistance confirming to is 15298 part - ii (size-8/9/10 inch) , barrication tape (6 inch) 250 mtr roll made out of pe/pp film with work in progress printed on both sides as per ansi z53 5.5 , chemical goggles with indirect ventilation made of pvc frame and fitted with polycarbonate lengths and non allergic elestic band confirming to en 160 , acid/ alkali proof gloves having size of 18 inch with palm m , normal dangari (size-l) with having an is-11612 are made of various fabrics like treated cotton , fire proof dangari (size-l) having is-11612 are made of inherent fire retardent fabrics , safety helmet made up of thermoplastic polymer with inside eight point textle/nylon harness with sliding adjustment with chin strap and rachet confirm to is-2925:1984 colour :- white , safety helmet made up of thermoplastic polymer with inside eight point textle/ nylon harness with sliding adjustment with chin strap and rachet confirm to is-2925:1984 colour :- green , impregnated granular activated carbon multi gas filter cartridge having is- 15323 :2003 , foot operated eye and face washer combination units are made of powder coated anti corossive gi pipes as per is 10592 , carry sheet (stretcher) l x b: 212 x 75 cm with self weight 1 kg, load limit 159 kg, lift type: horizontal , wind indicator made of light weight pu coated nylon material. double stitch at all joints. , plastic eyelets gives anticorrosion proper-ties. the complete wind sock comes with a polymer packing. 2" dia and 6 ft length along with wind indicator stand is made of good quality non corrosive galvanized iron (gi) pipe. , ear plugs corded epsav-570 , nose/ dust mask rpsav-p2 , flash light distance 243 mtr. run time:2 hr. 15 min. compliance: none, lumens. 164 , vapour respirator with head stripes to accommodate twin cartridges with exhalation valve , safety net consisting of pp rope dia: 4mm, mesh size: 100 mm, outer rope dia: 12mm supported by an additional nylon net (fish net), rope breaking strenght report should be as per is size 5mtr x 10 mtr , ear muffs, ce marked, made from impact proof polypropylene with multi position soft polymer head band. foldable compact size for storage. approved from en 352-2, snr 27 db(a) , heat shield hand gloves made of normal and tannedsplit leather of reddish-brown colour. , insulating thermalbarrier as inner layer gives heat protection upto 250 degrees. thumb re-inforcement enhances usage life. best for weldingtand general heat applications size 10 length 12.5", approved from en407-423x4x, en388-4344 , insulated hand gloves with working voltage of 17000 volts and proof voltage 25000 volts length of 14 inch, confirm to erda 4770:1991 , electrical hand gloves, for 2000 volts dc, coating material natural rubber latex, liner material non flocked, cuff style rolled beaded/gauntlet, grip design smeeth finish, confirm to erda 4770:1991 , hot oil splash suit, a five layer garment made of csm material, meta aramid, inherent cotton, aramid felt & inherent fr. the fabric withstanding pressure caacity is 50kg/cm2 and steam strength is up to 350c temperature.it should be atira tested for 250c splash, tested to iso 5025,9151,6942,9185 and en 1875-3 , chemical splash goggles with indirect ventilation, protect against splash and a hard-coated polycarbonate lens that reduces uvb and uva radiation from natural sunlight by 99%, approved from ansi z.87.1.2003 , chemical handling gloves, protect from acid alkali, sulfuric acid, size 18" as per en 374:2003 , elecrical shock proof helmet, material should be hdpe, weight should not be more than 325 gms design should be aerodynamic size is 520 to 600 mm, confirm to is 2925:1984 for head protection 30 kv , chemiflex latex gloves, length-300 mm, en si
Tender For supply of hydraulic jack 50ton cen 76mm 700bar,hydraulic jack 30ton cen 64mm 700bar,hydraulic hand pumpoil 1.2 280 48,hydraulic hand pumpoil 4.1 700 66