Tender For bid to ras supply of repair maintenance of ewbb roller plain roller rocking and jack hydraulic 15 ton c c - repair oblice maintenance of ewbb roller plain 10 nos roller rocking 09 nos and jack hydraluic 15 ton 10 nos at ge ep jodhpur , taking out to contractor work shop for repair oblice maintenance and brought back to ge ep , repair oblice maintenance removing old loose paint roller plain 10 nos and roller rocking 09 nos as per rate analysis s no 2 , repair oblice maintenance jack hydraulic 15 ton 10 nos as per rate analysis s no 3 , dismantilling and re assembling jack hydraulic , complete oiling and greasing jack hydraulic , dismantilling and re assembling roller plain and roller rocking , s and f en series steel bush as per sample , s and f pin cotter 25 mm long as per sample , s and f pin cotter 50 mm long as per sample , s and f special sliding pin 63 mm cir as per sample , s and f grease filling lid as per sample , s and f en series steel shaft as per sample , s and f mild steel handle as per sample , s and f nut bolt washer and spring washer as required , s and f special roller as per sample , s and f side oblice middle main bush plate as per sample , applying grease to each bush and shaft 0 point 25 kg per 450 per kg 112 point 50 , main body alignment center lining measuring and adjusting angles etc on special cnc machine , roller alignment center lining measuring and adjusting angles etc on special cnc machine , re threading oblice strengthening old threads , re welding broken welds and strengthen welding after proper grinding oblice cleaning , requirement of redoxidemetalprimer , requirement of steel wire brush , requirement of cotton waste , requirement of turpentine oil oblice thinner , requirement of olive green metal paint , applying 03 coats of paint , numbering and naming of part with white metal paint ) /bid number : gem/2025/b/6830628 * /dated: 01-11-2025 & & / bid document 1 / 21
Tender For bid to ras supply of repair oblice maintenance of bb oblice ewbb jack lifting 15 ton 25 nos at ge ep jodhpur , taking out to contractor work shop for repair oblice maintenance and brought back to ge ep , repair oblice maintenance cleaning of all moveable ends bush shaft etc by petrol oblice kerosene as per rate analysis s no 2 , dismantilling and re assembling after servicing , complete oiling and greasing , s and f pin cotter as per sample , s and f en series steel bush as per sample , s and f special sliding pin as per sample , s and f nut bolt washer and spring washer as required , s and f mild rubber packing set , s and f steel shoe as per sample , s and f en series steel shaft as per sample , s and f grease filling lid as per sample , requirement of redoxidemetalprimer , requirement of steel wire brush , requirement of cotton waste , requirement of turpentine oil , requirement of olive green metal paint , applying 03 coats of paint , numbering and naming of part with white metal paint labour only , requirement of first quality ultra white glossy finish synthetic enamel paint for writing part name oblice number 40 ml nos , main body alignment center lining measuring and adjusting angles etc on special cnc machine , shaft alignment center lining measuring and adjusting angles etc on special cnc machine , welding broken welds and strengthen welding after proper grinding oblice cleaning , re threading oblice strengthening old threads
Tender For corrigendum : procurement of security related items/systems as per directions of security agencies like 04 no. integrated tyre burster with boom barrier etc. - steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. (for further details refer sbd) , solid plastic tyre on steel rim minimum dia. 4 inch (for further details refer sbd), painting with synthetic enamel paint of approved brand and manufacture to give an even shade. two or more coats on new work (for further details refer sbd), lettering with black japan paint of approved brand and manufacture. (for further details refer sbd), carriage of material by means of mt for steel for 50 kms (mt)
Tender For providing and fixing of fire equipment - dry chemical powder fire extinguisher ( store pressure type) capacity 4 kg duly isi marked conforming to is:15683:2006 with map abc powder complete with squeeze grip release valve, discharge pip, locking arrangement pressure gauge operating manual and bracket. operating temperature:- 10 c to +55 c, co2 type fire extinguisher isi marked conforming to is:15683 capacity 4.5kg complete with delivery hose horn, wheel type release valve locking arrangement operation manual and bracket operating temperature 30 +55 c, co2 wheeled fire extinguisher isi marked conforming to is:16018 capacity 22.5kg complete with trolley with handle & wheel operation manual wheel type release valve locking arrangement and shut off valve fitted with delivery hose horn. operation temperature 5 cto +55 c, dry chemical powder (dcp) type fire extinguisher 9.0 kg is: 15683 operating temperature 0 c to 55 c for class 4a type of fire complete with squeeze type lever, and hose filled with isi mark power is:4308 complete in all respect. (ma,e omex/life guard/cease fire/minimax/ex-flame, fire bucket with round bottom having two handle, one at the top and other at one side of the bucket for throwing sand/water. the bucket should be painted outside with one coat of anti corrosive redoxideprimer and two coats of red enamel paint and inside the bucket shall be painted with one coat of redoxideprimer and two coats of white enamel paint. the bucket should be written in the words "fire". the water capacity of the bucket shall be 9 ltrs., fire becket stand ( suitable for 8 nos. buckets in each stand) made of ms angle of size 50x50x6 mm buckets should be hanged on suitable hooks made of ms round bar along with shade duly painted with po red enamel paint word "fire" written in it., construction of hut of size 12 feet x 10 feet x 7 feet for protection against direct sunlight and rains of fire extinguishers and fire buckets to avoid mal operation of above equipment by grouting of ms angle/ pipe of suitable size (to be provided by the department) with cement concrete with cement, coarse sand and 20mm stone ballast in ratio of 1"2:4, providing & fixing of asbestos cement sheet ( minimum 6mm thickness) at roof top, making steel frame for hut with help of ms angle/ pipe of suitable size including fabrication, erection & fixing of asbestos cement sheet with j-hooks of hut & frame and then painting of ms angle/pipe and sheet with two coat of standard make red synthetic enamel paint of first quality after cleaning of rust, dust and oily surface including cost of all material labour and t&p as per technical specifications
Tender For bid to ras supply of repair oblice maintenance of bailey bridge roller rocking mk ii 55 nos at ge ep jodhpur , taking out to contractor work shop for repair oblice maintenance and brought back to ge ep , repair oblice maintenance oblice overhauling removing old loose paint grease salt scratching with steel wire brushes cleaning of all moveable bush shaft etc by petrol oblice kerosene , dismantilling and re assembling , s and f steel bush as per sample , s and f pin cotter 25 mm long as per sample , s and f pin cotter 50 mm long as per sample , s and f special sliding pin 63 mm cir as per sample , s and f nut bolt washer and spring washer as required , s and f mild steel chain with accessories , s and f mild steel shoe 50 mm dia as per sample , s and f en series steel shaft as per sample , s and f grease filling lid as per sample , requirement of redoxidemetalprimer , requirement of steel wire brush , requirement of cotton waste , requirement of turpentine oil , requirement of olive green metal paint , applying 03 coats of paint , numbering and naming of part with white metal paint
Tender For bid to ras supply of repair oblice maintenance of bb roller plain 50 nos at ge ep jodhpur , taking out to contractor work shop for repair oblice maintenance and brought back to ge ep , repair oblice maintenance moveable ends bush shaft etc by petrol o0blice kerosene as per rate anaysis s no 2 , dismantilling and re assembling complete and arranging on ground , s and f en series steel bush as per sample , s andf grease filling lid as per sample , s and f en series steel shaft as per sample , s and f mild steel handle as per sample , s and f nut bolt washer and spring washer as required , s and f special roller as per sample , s and f side oblice middle main bush plate as per sample , applying grease to each bush and shaft 0 point 25 kg per 450 per kg 112 point 50 , main body alignment center lining measuring and adjusting angles etc on special cnc machine , roller alignment center lining measuring and adjusting angles etc on special cnc machine , re threading oblice strengthening old threads , welding broken welds and strengthen welding after proper grinding and cleaning , requirement of redoxidemetalprimer , requirement of steel wire brush , requirement of cotton waste , requirement of turpentine oil oblice thinner , requirement of olive green metal paint , labour for appling paint , numbering and naming of part with white metal paint , requirement of first quality ultra white glossy finish synthetic enamel paint for writing part name oblice number 40 ml nos , requirement of sand paper 02 nos per roller plain
Tender For supply of purveying upkeeping of detachable frames 12 nos : : - purveying oblice upkeeping of detachable frames at ge ep jodhpur , required hollow tail section 50 x 30 mm , required hollow tail section 20 x20 mm , required cold rolled mild steel wrinkle free prickled sheet 0 ponit 8mm thick , required other mild steel items , requiredredoxidemetalprimer , required og metal paint , required thinner , fabrication of detachable frame complete with welding rods and labour , complete paints with paints tools and labour