Get complete information related to latest Release Spring Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Release Spring Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Release Spring Tenders.
Tender For supply of repair maintenance of eicher vehicle at af stn memaura -complete vehicle servicing with replacement of following spares , fuel filter , oil filter , bypass filter , air filter , engine oil make castrol servo hp , fan belt , gear oil make castrol gulf bosch , grease make servo , labour charge for servicing , servicing and cleaning of radiator complete with acid wash and brazing the leakage points , coolant , expansion tank , labour charge , complete repair replacement by dismantling rear spring leaf both sides left and right from vehicle carefully reassembling and refitting on vehicle after replacement of the following spares , rear left and right side main leaf , bushes , pad , clamps , center bolt , labour charges , checking repair to electrical system with complete inspection and rectify fault if any by replacement of following spares , distill water , complete clutch overhauling with repair replacement by dismantling unserviceable items from vehicle carefully reassembling and refitting on vehicle after replacement of the following spares , clutch plate , clutch pressure plate , clutch release bearing , complete repair of brake system by dismantling unserviceable items from vehicle carefully reassembling and refitting on vehicle after replacement of the following spares , brake oil make bosch tvs waxpol , brake shoe , brake master cylinder , complete wheel balancing , labour charge including tyre rotaion
Tender For supply of spring assy front,clutch release bearing,relay starter solenoid,relay assy,coolant pump assy,hand brake cable,s a water pump b 7016007,master cyl power,cover assy 1 75 inch spline,assy 310 dia clutch disc
Tender For tender for supply of 01.size clear opening diameter 800 mm 02.color green on both sides.the handles to be marked with photo luminescent tapes. 03.opening mechanism-escape scuttles are to be spring assisted and provided with a wheel assembly on the inside and a slot with a detachable operating handle from outside for opening and closing of the scuttles.the operating handle should be supplied with associated bulkhead-mountable press-fit clamps to enable securing the operating handle onto the bulkhead. 04.material- as per class requirement 05.all ees are to be flush type spring assisted with auto retention clip and operable from above and below by one person.they are to be provided with an opening arrangement from above with detachable operating handle and press-fit clamps for securing the handle on to the nearest bulkhead. 06.ees are required to operable from both sides and tested up to 1.2 bar pressure or as per class requirement 07.marking- each scuttle should have punch mark with oem name date of fabrication month and year .marking symbols should be prominent legible and i.a.w. with nes118 and nes119. 08.rubber beading-rubber beading of silicone as per ncd 5910 are to be used for the ees , on board spares for ess consisting of the following -1.ss nuts and bolt sets- 10 nos -2.ss screws-10 nos -3.brass washers-10 nos -4.split pins-04 nos -5.silicon rubber beading-04 mtrs -6.adjustable spanner-01 nos , documentation -1.class approved drawings- 01 nos. -2.technical -operating-installation-testing and maintenance manual-01 nos. -3.inspection release note-inspection reports of inspection agency-certified test reports-materialtest reports-certificate for dimensional accuracy weight certificates with position of c.g etc-01 nos. -4.soft copy of all above documents in cd or pen drive-01 nos. , 01.size clear opening diameter 800 mm 02.color green on both sides.the handles to be marked with photo luminescent tapes. 03.opening mechanism-escape scuttles are to be spring assisted and provided with a wheel assembly on the inside and a slot with a detachable operating handle from outside for opening and closing of the scuttles.the operating handle should be supplied with associated bulkhead-mountable press-fit clamps to enable securing the operating handle onto the bulkhead. 04.material- as per class requirement 05.all ees are to be flush type spring assisted with auto retention clip and operable from above and below by one person.they are to be provided with an opening arrangement from above with detachable operating handle and press-fit clamps for securing the handle on to the nearest bulkhead. 06.ees are required to operable from both sides and tested up to 1.2 bar pressure or as per class requirement 07.marking- each scuttle should have punch mark with oem name date of fabrication month and year .marking symbols should be prominent legible and i.a.w. with nes118 and nes119. 08.rubber beading-rubber beading of silicone as per ncd 5910 are to be used for the ees , on board spares for ess consisting of the following -1.ss nuts and bolt sets- 10 nos -2.ss screws-10 nos -3.brass washers-10 nos -4.split pins-04 nos -5.silicon rubber beading-04 mtrs -6.adjustable spanner-01 nos , documentation -1.class approved drawings- 01 nos. -2.technical -operating-installation-testing and maintenance manual-01 nos. -3.inspection release note-inspection reports of inspection agency-certified test reports-materialtest reports-certificate for dimensional accuracy weight certificates with position of c.g etc-01 nos. -4.soft copy of all above documents in cd or pen drive-01 nos. , 01.size clear opening diameter 800 mm 02.color green on both sides.the handles to be marked with photo luminescent tapes. 03.opening mechanism-escape scuttles are to be spring assisted and provided with a wheel assembly on the inside and a slot with a detachable operating handle from outside for opening and closing of the scuttles.the operating handle should be supplied with associate