Get complete information related to latest Ring Plate Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Ring Plate Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Ring Plate Tenders.
Tender For s/i/t/c of e/m equipments and allied works for newly re-bored tube well at okhla vihar near majar in okhla constituency ac-54. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 15 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point: 200-125-75 lpm on 89-124-133 mtr. head.having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved. , supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted. a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no. b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 no c) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no. e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable banking g) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos.complete wiring &installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated and pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs. make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., supply of ms nut bolts off size as per requirement., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 1x1 made out from 6mm thick m.s. sheet in 2 halves and a circular hole in centre 3-1/2 dia. with locking arrangement by nuts and bolt. , earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.
Tender For corrigendum : tender for supply of earth work in excavation by mechanical means , filling by brought out excavated earth , providing and laying in position specified grade of reinforced cement concrete , supplying and filling in plinth with sand floors , providing and laying in position specified grade of reinforced cement concrete , shuttering in foundations , shuttering in superstructure columns , steel reinforcement for rcc , applying priming coats with primer , wall painting with acrylic emulsion paint , structural steel work riveted , brick work with common fly ash bricks , half brick masonry with non modular fly ash bricks , 15 mm cement plaster with mix , providing frosted glass panes 4 mm thick , neat cement punning. , painting with synthetic enamel paint , finishing walls with acrylic smooth exterior paint , providing and laying ceramic glazed floor tiles , providing and laying 60mm thick factory made cement concrete paver block , 6 mm cement plaster of mix , providing and fixing on wall face unplasticised rigid pvc rain water pipes , grading roof for water proofing treatment , making soak pit , providing and fixing gi , do gi pipe 20m dia , do gi pipe 25m dia , do gi pipe 40m dia , providing and fixing white vitreous china pedestal type , providing and fixing white vitreous china wash basin , providing and fixing precoated galvanised steel sheet roofing accessories , supplying and applying two coats of white wash , providing and placing on terrace polyethylene water storage tank , providing and fixing ptmt pillar cock , providing and fixing on wall face un plasticised rigid pvc swr , providing and fixing brass bibcock , providing and fixing mirror of superior glass , providing and fixing cp brass shower rose , providing and fixing cp brass shower valve rose , clearing jungle , 30 mm thick factory made polyvinyl chloride , supplying chemical emulsion , providing and applying white cement based putty , laying of one number pvc , supplying and fixing cable route marker , supplying and making end termination , supplying and fixing of following ways surface , supplying and fixing following rating , supplying and fixing dp sheet steel enclosure , supply of exhaust fan , installation of exhaust fan , supply of ceiling fan , installation testing and commissioning of ceiling fan , supply of ceiling fan regulators , supplying of led lights 20w , supplying of led lights 36w , supply of amps switch piano switch , supply of socket , supply of switch , supply of socket outlet , supplying and fixing 3 pin required. , supplying and fixing suitable size gi box , wiring for circuit submain wiring , wiring for circuit/ submain wiring alongwith earth wire , installation testing commissioning of wall bracket , providing and fixing danger notice plate , supplying and fixing metal box , supplying and fixing metal box , providing & fixing fixing metal box , earthing with copper earth plate , providing and fixing 25 gi , providing and fixing of lightning conductor finial , providing and fixing , providing and fixing gi , providing and fixing gi
Tender For supply of 2 cond. terminal block - gray colour of m/s wago part no. 260-301 or eqv. part of following makes m/ , end plate gray colour of m/s wago part no. 260-361 or eqv. part of following makes m/s phoenix, m/s
Tender For tender for supply of supply of bi pin halogen lamp 200w , 6.6a suitable for mirl/hirl fitting complete as per site requirement. make- osram cat no.64386 or equivalent as per preferred make of aai. , supply of halogen lamp wih inbuilt holder of 105w , 6.6a , suitable for ocem make (p/n - slre-s-cpc-1p-200-o , code - 007.6255) inset type runway edge light fitting. model-64339 a 105-6.6 , make-osram or equivalent as per preferred make of aai. , supply of halogen lamp wih inbuilt holder of 105w , 6.6a , suitable for ocem make (p/n - slre-s-cpc-1p-200-o , code - 007.6255) inset type runway edge light fitting. model-64339 c 105-6.6 , make-osram or equivalent as per preferred make of aai. , supply of runway lamp holder suitable for 200 w bi pin halogen lamp complete as required as per site requirement. , supply of led strip for led based airfield signages suitable to be operated on input source of 2.5 amp to 6.6 amp constant current , 20v-25 v dc supply compatible for signboards complete as per site requirement. 1.2 mtr strip , supply of led strip for led based airfield signages suitable to be operated on input source of 2.5 amp to 6.6 amp constant current , 20v-25 v dc supply compatible for signboards complete as per site requirement. 0.7 mtr strip , supply of bi-directional elevated high intensity halogen type runway edge light fitting complete with prefocus lamp holder , upto 200 watt 6.6 a halogen lamp , clear outer prismatic dome , clear inner prismatic lens , 180 degree yellow filter/lens , 180 degree clear filter/lense , lense holding mechanisam , ball joint for easy leveling , breakable coupling , central column mounting assembly , gaskets , two pin secondary lead plug suitable for connection , base plate with 6 nos. m-10 stainless steel bolts , spring and plain washers and other accessories etc. and confirming to particular specification with lens including lamp etc. as required to meet latest icao requirement. make- as per aai approved make. , supply of 180 degree yellow filter lense suitable for 200 w ama make elevated type runway fitting as per site requirement. , supply of 180 degree yellow filter lense suitable for 200 w vardhman make elevated type runway fitting as per site requirement. , supply of 180 degree red filter lense suitable for 200 w vardhman make elevated type runway fitting as per site requirement. , supply of green spreader lense/glass suitable for elevated type runway threshold light fittings of make - thorn. , supply of green spreader lense/glass suitable for elevated type runway threshold light fittings of make - ama. , supply of clear spreader glass/lens suitable for elevated type simple approach light fitting of make - ama. , supply of red spreader lense suitable for elevated end light fitting of make - ama. , supply of red spreader lense suitable for elevated end light fitting of make - thorn , supply of reflectors suitable for elevated type thresold light fittings of make - thorn. , supply of reflectors suitable for elevated type simple approach light fittings of make - ama. , supply of 180 degree clear filter lense suitable for 200 w ama make elevated type runway fitting as per site requirement. , supply of isolating transformers of 200w , 20/6.6 amp rating of 5 kv grade , 50hz , series type , encapsulated in polyester resin finally moulded with neoprene rubber with primary and secondary connections as specified in particular specifications , complete as required. , supply of ss earth bolts of m10 x 25 mm suitable for fixing the housing box/msas per site requirement. , supply of 9 watts led bulb , 230v , 50hz , ac supply suitable for normal holder. , supply of red filter with holder (complete replacable kit) suitable for runway edge light inset fitting of ocem make (p/n - slre-s-cpc-1p-200-o , code - 007.6255) as per site requirement. , supply of yellow filter with holder (complete replacable kit) suitable for runway edge light inset fitting of ocem make (p/n - slre-s-cpc-1p-200-o , code - 007.625
Tender For supply of routine and breakdown maintenance works of aph -replacement of heating element.when the elements strips are to be dismantled and cleaned with wire brush. , servicing and minor repairing of flue gas primary air and secondary air inlet, outlet and inter connecting dampers of aph. flue gas dampers. , servicing and minor repairing of flue gas primary air and secondary air inlet, outlet and inter connecting dampers of aph.primary air damper , servicing and minor repairing of flue gas primary air and secondary air inlet, outlet and inter connecting dampers of aph.secondary air damper , servicing of flue gas primary air and secondary air inlet, outlet and inter connecting dampers of aph flue gas dampers. , servicing of flue gas primary air and secondary air inlet, outlet and inter connecting dampers of aph primary air damper , servicing of flue gas primary air and secondary air inlet, outlet and inter connecting dampers of aph secondary air damper , repairing of flue gas, sa, pa inlet and outlet duct manholes cover. , repairing flue gas dampers flaps. , repairing of pa damper flaps. , repairing of sa damper flaps. , repairing of semi circular baffle. , repairing of distance pieces in fg duct. , repairing expansion joints before and after air pre heater. , cleaning of cooling water line of lubricating oil pumps of aph by cutting and welding. , repairing of hangers of sector plate. , decoupling and re-coupling of electrical motor for replacement of electric plate and fluid coupling etc. , fabrication of bracket 1 set equal to one no. in board and one no. in outboard bracket. , replacement of brackets. , leveling of rotor. , water washing and cleaning of flue gas duct sa duct. , providing sealing cover on expansion joints. , repairing of t-bars. , replacement and repairing of fg duct by cutting and welding. , adjustment of axial seal plate. , complete replacement of the static seal of aph , re- visioning or repairing of air seal housing of guide bearing of aph. , alignment of electric motor and air motor with reduction gear box of air pre-heater. , replacement of gear box of air pre heater. , cleaning of water washing nozzle, elbow and socket. , repairing of oil or water valve lube oil system of size 25mm. to 40mm. , replacement of oil or water valve lube oil system of size 25mm. to 40mm. , servicing or overhauling of over running clutch system of aph. , checking of gear box of aph. , cleaning or servicing of support bearing and their housing. , repairing and reconditioning of centre section surface beneath guide bearing and casting the refractory. , leveling of sector plates of hot end or cold end. , replacement or reversal of he ie ce basket aph. , hot washing of air pre heater. , cleaning of air pre heater through nozzle. , round the clock checking and routine maintenance of air pre heaters of unit no 12 and 13 btps, obra , round the clock checking and routine maintenance of air pre heaters of unit no 9,10,11 btps, obra
Tender For supply of clutch disc assy , pressure plate , d l kit small , d l kit big , gear lever end kit , trim pad lh , isolator switch , universal joint cross , assy rear view mirror
Tender For supply of pre-fabricated steel tubular ffl 2 oblic 1 structure of size 2.40 x 2.40m , quick setting compound rapidite make acclerex cico fosroc , aggregate 20mm. stone aggregate to be crushed rock or gravel 20mm graded , aggregate 40mm. stone aggregate to be crushed rock or gravel 40mm graded , manufactured sand m sand confirming to is 383 2016 specifications for coarse and fine aggregates. , bricks cement pcc brick of size 230mm x 115mm x 75 mm with sharp corners , non skid ceramic tiles coloured 7 to 8 mm thick in floors , liquid water proofing compound is 2645 2003 , white cement packet 01 kg , pvc ceiling rose 2 obliq 3 terminal with pvc square box complete with screws , led tube light fitting 1 x 12 w 2 feet long complete with all accessories including led tube rod , pvc cable insulated and pvc sheathed 1.50 sq mm twin core with copper conductor , flexible wire pvc insulated twin core twisted of size 23 obliq 0.0076 with copper conductor , modular switch one way 6 amp 1 module , white cover plate with frame 2 module , white cover plate with frame 3 module , metal flush box 2 module , metal flush box 3 module , mcb double pole 230v ac 50 hz 16 amps 10ka confirming to is 8828 1996 , mcb distribution board in sheet metal enclosure two ways with blanks conforming to is 8828 1978 , ms screw 20 mm full threaded per pkt 100 nos conforming to is 723 1972 , tape insulation 2 cm width 10 mtr long isi marked , pvc casing caping 25 mm x 16mm , pvc casing caping square box 4 inch x 4 inch , pvc body exhaust fan 250mm sweep with lowers , vitreous china squatting pan orissa pattern size 580 x 440 mm white with integral foot rests , pvc valve less syphonic action type low level flushing cistern 10 ltrs capacity , 110mm dia upvc pipe 3 mtr long single socketed with cowl , 110mm dia upvc single tee , 110 x 110mm nahani trap with jali , 4 inch dia upvc bend , 15mm brass stop cock conforming to is-8934 1978 , 3 layer of pp r polypropylene random copolymer pipes sdr 7.4 , 20mm elbow suitable for 20mm dia ppr pipe conforming to is 1239 1989 , 20mm socket suitable for 20mm dia ppr pipes conforming to is 1239 1989 , 20mm equal tee suitable for 20mm dia ppr pipe conforming to is 1239 1989 , 20mm union suitable for 20mm ppr pipes conforming to is 12391989 , ppr end plug 20mm conforming to is 1239 1989 , ppr pipe clamp suitable for 20mm piping , bib cock 20 mm with flange conforming to is 8931 1978 , gi reducer socket 15 obliq 20mm , gi reducer elbow 15 obliq 20mm , pre fabricated man hole cover 6 feet x 4 feet made of isa 40x40x6mm frame , rotational moulded polyethylene water storage tank double layer , ppr tank connector 20mm with check nut and washer , white lead safeda , thread cotton ball 100 m long , vitreous china wash hand basin whb white flat back size 550x400 mm , 20mm dia pillar taps of ptmt of any colour high pressure screwed for iron pipe , 110mm dia upvc swr pipe single socketed pipe type a in any length with rubber joint , 600x450mm size looking mirror mounted on pvc with pvc shelf assembly including all fittings all as specified