Latest rod bolt Tenders | Government rod bolt Tenders

corporations/Associations/Others

CTN :38182426

19 Nov, 2024 NA

Multi City - Multi State

Tender For auction sale of dismantled engine scrap -tractor,scrap glass,automotive fabric scrap,scrap plastics - pcb category,rubber scrap -pcb category,chassis scrap,scrap rim- 4w,radiators and condensers scrap,scrap rim - tractor,seat scrap,scrap battery - pcb category,mix steel scrap - i,wiring harness,sheared body scrap l-4w,catcons - wire mesh,catcons - tractor,ms steel scrap - nuts and bolts,e -waste,car -jacks

Central Government/Public Sector

CTN :38005126

18 Nov, 2024 45.72 Lacs

Mundra - Gujarat

Tender For corrigendum : provn of 02 in nos bore wells alongwith associated items at icgs mundra - material and labour for drilling of 02 nos pilot/trial bore by direct rotary rig method including all t&p through any kind of starta (soil, kankar, boulder or soft or hard rock) down up to 150 m depth below ground level by using suitable drill bit according to levering of casing pipe including the cost of mud pit, channels, etc and disposal of soil obtained to a distance not exc. 1 km away complete all as specified. note:- (i) the drilling shall be continued up to specified depth and in case sticky clay occurs in between the drilling must be stopped and hydrologist of gws & sb shall be contacted & eggr-in-charge shall be informed.(ii)cost of this consultant shall be borne by contractor (iii) taking the samples from the bore well cutting for every 3 meter interval and every change in strata if less than 3meter. (iv) preparation of litho logs based on these samples.(v) drill time log to be prepared and prescribed., (vi) aquifer performance tests at constant discharge with draw down and recovery reading.(vii) after completion of pilot bore, the contractor shall have to arrange for electro eater logging test of each bore.(viii) contractor have also produced bore well water test report for drinking water parameters before levering of motor and pump.(note:- if water quality not found fit for domestic purpose use then all other connected items of trial bore will not be executed.) , supply assembling, jointing, lowering and fixing in the bore hole pvc casing pipe of nominal dia 315 mm (medium well) ,10 kg/cm2 working pressure, confirming to is 4985-2000 including providing pea gravel of 8 mm to 4.6mm size for packing around the casing/slotted pipe in bore well all as specified and directed. make: astral/ashirwad/ajay/sfmc, all as per item no 2.00 above but slotted pipe. , supply, assembling, jointing, lowering lead free pvc column pipes of nominal dia 65 mm, od 75 mm (min), non toxic, pressure 16 kg/cm2 with and including top and bottom adaptor (ss) and accessories like epdm ring and double ss stud all as spd and directed by engineer-in-charge. make: astral/ashirwad/ajay/sfmc, development of tube well with compressed air by means of air compressor of suitable capacity not less than 300 cfm and over pumping using suitable capacity pump to make available water free from turbidity complete all as specified and directed by engineer-in-charge., m & l for conducting yield test for the bore well by continuously pumping for 24 hours by using a submersible pump set to determine safe pumping yield and produced water test report of samples which is collect every hour complete as directed by the engineer-in-charge. [ all arrangements for yield test shall be made by contractor and cost for the same borne by contractor ], supply and fix ms reducer, bail plug, top cover made of 3mm thick ms plate for bore well in two half sections having a hole of 75 mm bore in centre to accommodate pvc pipe and submersible cable suitable for fixing to the pvc casing pipe top, electric logging and simple strata box including provision of 2 sets of ms clamps made of 50x6mm ms flat including nuts, bolts, etc. including one coat of epoxy primer and two coats of epoxy paint wherever necessary complete all as specified and directed by engineer-in-charge., supply, install, test and commissioning of submersible pump stainless steel body electric driven with submersible motor, water lubricate, 3 phase, 10.0hp (appx) 415 volts, 50 hz with suitable submersible electric motor suitable for discharge of 2 liters per second against total head of 125m in the bore complete all as specified and directed by the engineer-in-charge. [ note : column pipe, submersible cable and control gear will be measured and paid separately]. [make: kirloskar / crompton / ksb], supply, install, test and commissioning of submersible pump stainless steel body electric driven with submersible motor, wa

Central Government/Public Sector

CTN :38184935

04 Dec, 2024 NA

Visakhapatnam - Andhra Pradesh

Tender For supply of p way material for railway - fish plates , fish bolts , check blocks , ms bolts , ms round washer , fish plate

CTN :38198262

05 Dec, 2024 NA

Dehradune - Uttarakhand

Tender For supply of angle iron 65x65x6mm for fencing post of height 2.85 mtr with angular arm as per specification given in pdf , ms flat 50 x 5mm of 1.80 m height making 05 nos 15mm dia holes at a distance of 400 mm centre to centre as per specification given in pdf , ms flat 50 x 5mm of making 15 mm dia holes at a distance of 3.00 mtr centre to centre as per specification given in pdf , angle iron 50x50x6mm for strut post of height 2.35 mtr making 02 nos 15mm dia holes at a distance of 100mm centre as per specification given in pdf , two strand of barbed wire made out of gi wire of size 2.24mm dia barbed with 2mm dia barbs at 75mm as per specification given in pdf , supply only chain link fence with dia of wire 4 mm and size of mesh 100mm x 100mm make sail rinl jindal tata. , binding wire 0.9mm dia. , 12 mm dia 50mm long bolts with nuts 02 x washers for each set. , cement in polythene bags 50 kgs each grade 43 opc make jk ultra tech jaypee ambuja and cement corporation of india cci , sand coarse confiming to is as per specification given in pdf , crushed stone aggregate 20 mm graded confirming to is 383 970 2nd revision from natural sources , lime , commercial plywood 6 foot x 3 foot x 12 mm as per specification given in pdf , nails all type 1 inch to 6 inch long as per specification given in pdf , primer red oxide as per as per is 8982 as per specification given in pdf , synthetic enamel paint colour black white ist quality as per specification given in pdf , solar security light as per specification given in pdf , cutting plier 160mm long make as per specification given in pdf , leather hand gloves knitted industrial gloves as per specification given in pdf , ring spanner of 16mm x 17mm 14 x 16mm as per specification given in pdf , crowbar hexagonal 1200mm long x 40mm dia , plumb bob steel , bucket steel 15 ltr capacity as per sample , water level pipe 30 mtr length , brick hammer 250 gms with handle , welding rod , hdpe sheet 20 foot x 20 foot , wooden gurmala 6inchx3 inch , steel pan mortar of 18inch dia as per sample , showel gs with wooden handle , phawarah with wooden handle as per sample , paint brush 2 inch size nylon straight smooth bristles bonded properly and best quality

CTN :38198300

05 Dec, 2024 NA

Dehradune - Uttarakhand

Tender For supply of angle iron 65x65x6mm for fencing post of height 2.85 mtr with angular arm as per specification given in pdf , ms flat 50 x 5mm of 1.80 m height making 05 nos 15mm dia holes at a distance of 400 mm centre to centre as per specification given in pdf , ms flat 50 x 5mm of making 15 mm dia holes at a distance of 3.00 mtr centre to centre as per specification given in pdf , angle iron 50x50x6mm for strut post of height 2.35 mtr making 02 nos 15mm dia holes at a distance of 100mm centre as per specification given in pdf , two strand of barbed wire made out of gi wire of size 2.24mm dia barbed with 2mm dia barbs at 75mm as per specification given in pdf , chain link fence with dia of wire 4 mm and size of mesh 100mm x 100mm make sail rinl jindal tata. , binding wire 0.9mm dia. , 12 mm dia 50mm long bolts with nuts 02 x washers for each set. , cement in polythene bags 50 kgs each grade 43 opc make jk ultra tech jaypee ambuja and cement corporation of india cci , sand coarse confiming to is as per specification given in pdf , crushed stone aggregate 20 mm graded confirming to is 383 970 2nd revision from natural sources , lime , commercial plywood 6 foot x 3 foot x 12 mm as per specification given in pdf , nails all type 1 inch to 6 inch long as per specification given in pdf , primer red oxide as per as per is 8982 as per specification given in pdf , synthetic enamel paint colour black white ist quality as per specification given in pdf , solar security light as per specification given in pdf , cutting plier 160mm long make as per specification given in pdf , leather hand gloves knitted industrial gloves as per specification given in pdf , ring spanner of 16mm x 17mm 14 x 16mm as per specification given in pdf , crowbar hexagonal 1200mm long x 40mm dia , plumb bob steel , bucket steel 15 ltr capacity as per sample , water level pipe 30 mtr length , brick hammer 250 gms with handle , welding rod , hdpe sheet 20 foot x 20 foot , wooden gurmala 6inchx3 inch , steel pan mortar of 18inch dia as per sample , showel gs with wooden handle , phawarah with wooden handle as per sample , paint brush 2 inch size nylon straight smooth bristles bonded properly and best quality

CTN :38198355

05 Dec, 2024 NA

Dehradune - Uttarakhand

Tender For supply of angle iron 65x65x6mm for fencing post of height 2.85 mtr with angular arm as per specification given in pdf , ms flat 50 x 5mm of 1.80 m height making 05 nos 15mm dia holes at a distance of 400 mm centre to centre as per specification given in pdf , ms flat 50 x 5mm of making 15 mm dia holes at a distance of 3.00 mtr centre to centre as per specification given in pdf , angle iron 50x50x6mm for strut post of height 2.35 mtr making 02 nos 15mm dia holes at a distance of 100mm centre as per specification given in pdf , two strand of barbed wire made out of gi wire of size 2.24mm dia barbed with 2mm dia barbs at 75mm as per specification given in pdf , supply only chain link fence with dia of wire 4 mm and size of mesh 100mm x 100mm make sail rinl jindal tata. , binding wire 0.9mm dia. , 12 mm dia 50mm long bolts with nuts 02 x washers for each set. , cement in polythene bags 50 kgs each grade 43 opc make jk ultra tech jaypee ambuja and cement corporation of india cci , sand coarse confiming to is as per specification given in pdf , crushed stone aggregate 20 mm graded confirming to is 383 970 2nd revision from natural sources , lime , commercial plywood 6 foot x 3 foot x 12 mm as per specification given in pdf , nails all type 1 inch to 6 inch long as per specification given in pdf , primer red oxide as per as per is 8982 as per specification given in pdf , synthetic enamel paint colour black white ist quality as per specification given in pdf , solar security light as per specification given in pdf , cutting plier 160mm long make as per specification given in pdf , leather hand gloves knitted industrial gloves as per specification given in pdf , ring spanner of 16mm x 17mm 14 x 16mm as per specification given in pdf , crowbar hexagonal 1200mm long x 40mm dia , plumb bob steel , bucket steel 15 ltr capacity as per sample , water level pipe 30 mtr length , brick hammer 250 gms with handle , welding rod , hdpe sheet 20 foot x 20 foot , wooden gurmala 6inchx3 inch , steel pan mortar of 18inch dia as per sample , showel gs with wooden handle , phawarah with wooden handle as per sample , paint brush 2 inch size nylon straight smooth bristles bonded properly and best quality

CTN :38198649

03 Dec, 2024 NA

Bardhaman - West Bengal

Tender For supply of submersible pump 20 hp elect driven 415v suitable for 250mm dia bore well , casing pipe size 300mm , submersible pump 25 hp elect driven 415v suitable for 250mm dia bore well , casing pipe size 300mm for 25 hp , ms erw pipe 100mm dia both side flange ms pipe including nuts and bolts

CTN :38184779

03 Dec, 2024 NA

Chandigarh - Chandigarh

Tender For supply of hardware items - nail 25 mm , nail 50 mm , panel pins wire nails , nail 75 mm , nail 100 mm , aluminium sliding door bolts 250 mm , natural wooden beading patti 75 mm , black screw , star screw 19 mm , star screw 25 mm , star screw 30 mm , star screw 35 mm , door handles 150 mm type c , door handles 200 mm type d , door spring , steel butt hinges 100 mm , steel butt hinges 75 mm , ms wire mesh , pvc gitti 1 inch , door stopper , tower bolt ss 6 inch , tower bolt ss 4 inch , wooden cutting blade , piano hinges , door closer , magnet catcher brass , mortise door lock , brass handle , double acting spring hinges , iron handle , iron tower bolt , aluminium snap bidding length 12 feet , aluminium glass rubber , fevicol 5 litre , silicon clear with gun , silicon sealent , nail 14 number , tile cleaner rauf 5 ltr , murga jali , telescopic channel 16 inch , telescopic channel 18 inch , telescopic channel 20 inch , drawer lock , cupborad lock bid number/ ( ( ) ): gem/2024/b/5595454 dated/* : 12-11-2024 bid document/ 1 1 / 37

CTN :37986608

14 Nov, 2024 NA

Tinsukia - Assam

Tender For corrigendum : supply of pcc blocks bricks , cement , sand , aggregate 20 mm , steel gate 3300x3300mm with frame of ms angle 50x50x5 mm and 2 shutter of ms angle 45x45x5 mm with 2 support 1 mm th ms sheet holdfasts 8 hinges handles aldrop bolt tower bolts and locking cleats , rod , cutting blade 4 inch , red oxide primer , enamel paint og , paint brush , thinner

CTN :37748954

15 Nov, 2024 NA

Purnia - Bihar

Tender For corrigendum : supply of plywood for general purposes as per is 303 (v2) (q3) , hydraulically regulated door closers (q3) , tower bolts (ferrous metals) as per is 204 (q3) , wood screws (q3) , non - ferrous metal butt hinges as per is 205 (q3) , wire nails (q4) , door handles as per is 208 (q4) , hasps and staples as per is 363 (q3) , wire mesh fabric or cloth (v2) as per is 1568 (q3) , stainless steel kitchen plate rack 30 cm into 36 cm into 9 cm , looking mirror 600 into 450 mm , fevicol 1 kg , pvc rawl plug 100 nos pkt , window glass ordinary 3 mm thick 1 point 2m into 1 point 2m , wooden beading of size 20mm into 6mm into 8 inch , wooden beading of size 20mm into 20 inch size 20mm into 6mm into 20 inch , round plug wooden , gi wire binding , bracket for curtain rod , putty 1 kg pkt , aluminum curtain rod 19 mm dia into 12ft lenght , super flush strip 100 mm wide 10 mtr long , pvc float valve 20 mm , gate valve brass 20mm , hack saw blade , gate valve 15 mm , gate valve 25 mm brass , pvc float valve 15mm , pvc float valve 25 mm , pvc stop cock 15mm dia , water storage tank 500 l isi marked , pvc lid for 1000 ltrs capacity , pvc lid for 500 ltrs capacity , m seal 200 gms pkt , brass jumper washer for 15 mm bib tap , hdpe grating 100 mm dia , gi hook for pipeline , gi check nut 20mm , gi check nut 25mm , cp glass self 450 mm long with 4mm glass , ms angle bracket for whb , cement 50 kg , white cement 1 kg , pad lock 6 lever , drill bit for brick hole 4mm 5mm 6mm 8mm and 10mm bid number/ ( ( ) ): gem/2024/b/5442434 dated/* : 02-10-2024 bid document/ 1 1 / 50

Rod Bolt Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

corporations/Associations/Others

Central Government/Public Sector

Central Government/Public Sector