Tender For corrigendum : supply of spares for cw pumps of unit. no. 3 & 4 at sikka tps. - coupling support of bhel make cw pump model no cw1q, moc bs 970 316 s16, abutment ring of bhel make cw pump model no- cw1q, moc bs 970 316 s16, muff coupling of bhel make cw pump model no- cw1q, moc bs 970 316 s16, bearing housing of cw pump type-cw1q, moc ss316, impeller nut of bhel make cw pump model no cw1q, moc bs 970 316 s16
Tender For supply of clamp washer minus ce minus d011 , clamp bolt minus 1nut minus ce minus d012m , bearing assy point dam 005 m , backliner stud thin self locknut minus cef144m , bowl seal ce minus eg6124 , clamp ring ce minus e6135 , discharge flange clamp bolt ce minus dg4270m , dischargre flange 2piece ce minus d4221 , discharge joint ring ce minus e4132 , adjusting screw minus 3nuts 2 washer ce minus d001m , base frame cyclone feed pump , adaptor plate stud minus 1 nut ce minus dg039m , shaft sleeve o minus ring 6 by 4 ddah pump d109 , shaft sleeve , adaptor plate ce minus dg4032m , seal ring for pump 6 by 4 dah e122 , back liner ce minus dg4041m , clamp ring bolt minus nut ce minus e129m minus , impeller 3 minus vane choke less , bowl ce minus dg4131 , intake flange clamp bolt minus 1 nut minus cedg4270m , intake flange 2 piece ce minus e6130 , intake joint ring ce minus f6132 , gland 2piece ce minus d044 , seal guard ce minus dg4186 , support bracket ce minus dg4186a , support screw ce minus m10h2 minus 30sn , packing 6 by 4 ddah pump d111 , lantern ring ball mill discharge pump160 , neck ring ball mill discharge pump d067 , stuffing box ce minus dam078 , plug ce minus wp43p1 minus e , gland bolt minus 1nut minus 1 washer ce minus d045m , shaft spacer 6 by 4 ddah pump , impeller o minus ring ce minus d109 ) /bid number : gem/2025/b/6932826 * /dated: 27-11-2025 & & / bid document 1 / 34
Tender For bid to ras bid to ras supply of x2-misc-mg-7-00-014-00 gasket for silencer exhaust pipe assy , x3-mg-19-dynaf-8-47-008-07 bearing rod end , x3- mg19-dynaf-6-10-976 switch oil pressure , x3-mg19- dynaf-n-902-415-01 allen key head bolt m6 x 10 set 1 set of 4 pcs , x3-mg19-dynaf-700-135-07 support engine front , x3-mg19-dynaf-7-00-088-00 coupling tee , x3-mg19- dynaf-7-19-001-07 hose clamp 22-25 , x3-mg19-dynaf-n- 011-184-9 hexagon nut self locking , x2-misc- 457945461989 current sens ta 400 oblique 02a hole 25mm 50 oblique 60 , z3-mg19-dynaf-6-97-003-07 lube oil
Tender For supply of mechanical spares of l&t make wagon tippler and side arm charger installed at chp, csctpp, chhabra - 1 drive pinion dia 395.99 x 669 x 15 teeth, 2 spacer dia 218, 3 labyrinth ring dia 300 with fasteners, 4 bearing housing dia 380, 5 end cover dia 290 with fasteners, 6 end cover dia 290 for topmost drive pinion for limit switch, 7 round(shaft extension piece) dia 173 mm, 8 drive rack segment with pilot hole dia 20 including fasteners, 9 clamp arm cylinder rod spacer dia110, 10 pivot shaft inner spacer dia 175, 11 end cap seal for 175 dia shaft, 12 clamp pivot arm bush dia 110, 13 side beam link bracket, 14 ring feeder dia 280, 15 end cap dia 380, 16 spacer dia380, 17 roller dia 240 for end frame roller assembly, 18 roller bush dia 170 for end frame roller assembly, 19 guide roller spacer dia 180, 20 guide roller dia 250, 21 platform hook pin and bush, 22 inner gripper spacer bush dia 45, 23 outer gripper spacer bush dia 40, 24 gripper pad 30thk x 4000, 25 sprocket (150 teeth) od 458 mm for cam switch, 26 chain 2100 mm length for cam switch, 27 sprocket (38 teeth) od 120 mm for cam switch, 1 cushioning pad (full pad) dia 286 x 39.7, 2 cushioning pad (end pad) dia 286 x 23.8, 3 cushioning pads (full pad) dia 225 x 41, 4 cushioning pads (end pad) dia 225 x 23.5, 5 thrust plate dia 280, 6 coupler, 7 forward housing dia 203 x 110 with fasteners, 8 rear housing plate dia 390 with fasteners, 9 spacer tube dia 150, 10 flanged bush dia 90, 11 buffer arm head pivot pin dia 100, 12 buffer arm tail pivot bush dia 100, 13 arm pivot pin dia 170, 14 thrust washer dia 180, 15 compression spring dia 135, 16 axle dia 110, 17 spacer dia 225 / 210, 18 pivot shaft dia 80 for sprung support roller, 19 bush dia 120 for pivot shaft, 20 upper bearing retainer plate dia 310 with fastners, 21 lower bearing retainer plate dia 350 with fastners, 22 upper spacer dia 190, 23 lower spacer dia 162, 24 drive shaft dia 150, 25 upper spacer dia 160 / 140, 26 lower spacer dia 160 / 130, 27 labyrinth seal dia 415
Tender For supply of bearing support(front) (hw-062. 03) - fully m/cd & assembled item as per drg. 21203701050 rev. 01 with , bracket (hw-062. 37) -- fully m/cd item as per drg. 11205501010 rev. 00 with matl. as per cbom 1120550 , support block (hw-064. 06) -- fully m/cd item as per drg. 21201901210 rev. 03 with matl. as per cbom 2 , support ring (hw-062. 13) -- fully m/cd item as per drg. 11203724020 rev. 01 with matl. as per cbom 11