Tender For supply of adjustable screw , valve spring outer , push rod , v belt a 43 ywa elect st , set of hoses , valve cotter , valve exh , washer red fibre yda 13 32x1116x116 , spring washer air manifold , bolt 516 , nut , hose cumn between cylinder hea , banzo screw , stud ex manifold , hose clip , safety control h tw , water temprature switch , lop switch , joint cyl head , piston ring set , washer , jointcopper washer , pre fuel filter element , set of hose clips , luboilrail , joint 6ydc , hose connection , set of piston ring , set of gasket 4g11t , adjusting screw , valve spring inner , retaining coller , valve sterm seal , stud 3 4 , guide bush , valve inlet , rocker lever exhust , rocker lever inlet , valve exhaust , washer injector , hex bolt intake manifold , screw sump , spring washer , nut for rocker adjusting screw , hexagon nut , hollowscrew , banjo screw , copper washer , lub oil filter , pipe fuel outlet , nozzel , cogged belt , valve stem seal , spring cap , m14 150 bolt cyl head , set screw , con rod bearing top bottom , inlet valve , ex valve 4g11 series , valve collet , hose for bypass , hose , hose dia 50 x 280 , pipe fip to oil supply , fuel pipe filter to fip , leak off pipe , fuel pump pipe
Tender For supply and installation of open gym equipments and construction of epdm flooring under open gym equipment in shahdara south zone, under mplads funds for various locations of parks in municipal corporation of delhi. - supply and installation of open gym equipments and construction of epdm flooring under open gym equipment in shahdara south zone, under mplads funds for various locations of parks in municipal corporation of delhi., seated puller /pull chair made from c class g.i pipe. dimensions: - 1900mm (length) x 740mm (width) x 1920mm. (height). safe area:- 1.2mtr x 3mtr. seated puller equipment made up of c class g.i. pipe of different nb.nb stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. the center pipe is of 100nb made from c class g.i. pipe. bottom support is of m.s. round plate of dia 250 mm & 10mm thickness welded. all linkages are made up of 25nb c class g.i. pipe. the handle frame is of 32nb c class g.i. pipe. the seat frame is of 32nb c class g.i. pipe. to build structure bushes are used which are made from seamless pipe of 60mm o.d. and 5mm thickness as well as 60mm diameter solid bar bush used. the foundation used for fixing is a structure and made from center pipe of g.i. of 80 nb c class. welded with m.s. round plate of dia 250 mm & 10mm thick. main pipe supported with 25 mm x 25mm m.s. angles of 3 mm thickness and 20mm x 40mm crc square pipes of 3mm thickness. foundation cover closing cap is made from injection moulded plastic lldpe / hdpe. the seats and back rests are fitted on the outer frames are made up of m.s. sheet of size 330 mm x 300 mmx2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.closing caps are made up of from injection moulded plastic lldpe / hdpe.pins used of diameter 25mm and 17mm are made up from sae 8620 bright material. the bearings used are of 6205 2rs1 and 6203 2rs1 permanent lubricated sealed bearing of reputed brand.high tensile steel with galvanized nuts & bolts are used for assembly.thecirclips used for assembly are of a16. the gym equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based powder coating with polyster powder coating of at least 60 to 70 micron thickness using exonobel / berger make paints or its equivalent paints. the holding down/fixing of gym equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)., cross trainer /elliptical exerciser dimensions: - 1320mm (length) x 600mm (width) x 1750mm. (height). safe area: - 1.77 x 1.2mtr. cross trainer equipment made from c class g.i. pipe of different nb.nb stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. the main frame pipes are of 80nb c class g.i. pipe with single bend pipe with 250mm radius. the bottom support of m.s. round plate of dia 250 mm & 10mm thick. the handle frame is made up of 25nb c class g.i. pipe. the foundation used for fixing is a structure and made from center pipe of g.i. of 80 nb c class welded with m.s. round plate of dia 250 mm & 10mm thick. main pipe supported with 25 mm x 25mm m.s. angles of 3 mm thickness and 20mm x 40mm crc square pipes of 3mm thickness. to build structure bushes are used which are made from m.s. seamless pipe of 60mm od with 5 mm thickness. the footrests are made from injection moulded plastic lldpe / hdpe. closing caps are made up of injection moulded plastic lldpe / hdpe. pins used of diameter 35mm, 25mm, and 17mm are made up from sae 8620 bright .the bearings used are of 6007 2rs1 62052rs1 and 62032rs1 permanent lubricated sealed bearing of reputed brand. high tensile steel with galvanized nuts and bolts are used for assembly. the gym equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based powder coating with polyster powder coating of at least 60 to 70 micron thickness using exonobel
Tender For bid to ras supply of tata safari and sml bus engine ouerhauling spares e e -, anabond tube tata safari storme model2018 , hose set cooling system tata safari storme model2018 , old cotton dhoti for cleaning engine , engine componant and parts cleaner , wheel bearing front lh rh wheel tata safari storme model2018 , wheel bearing rear lh rh wheel tata safari storme model2018 , inlet exhaust valve sml bus t3500 , valve guide inlet exhaust sml bus t3500 , valve seal inlet exhaust sml bus t3500 , piston with pin and lock std sml bus t3500 , cylinder liner std sml bus t3500 , piston rings sml bus t3500 , con rod bushsml bus t3500 , main bearing 10 sml bus t3500 , big end bearing 10 sml bus t3500 , thrust washer std sml bus t3500 , water pump sml bus t3500 , main oil filter sml bus t3500 , sobp oil filter sml bus t3500 , eng. overhauling gasket kit sml bus t3500 , timing oil seal sml bus t3500 , main oil seal sml bus t3500 , diesel filter 01 ltr sml bus t3500 , diesel filter set 500ml sml bus t3500 , oil sending unit sml bus t3500 , temp sending unit sml bus t3500 , nozzle return pipe with clip sml bus t3500 , fan belt set complete sml bus t3500 , fly wheel assy sml bus t3500 , fly wheel ring sml bus t3500 , clutch and pressure plate with r brg sml bus t3500 , clutch lower cylinder sml bus t3500 , clutch master cylinder sml bus t3500 , gear shifting cables 2 nos sml bus t3500 , pedal rubber boot clutch brake sml bus t3500 , gear lever dust boot sml bus t3500 , complete bushing set front rear sml bus t3500 , cap raidator sml bus t3500 , flasher unit sml bus t3500 , combination switcn assy sml bus t3500 , air filter sml bus t3500 , shaft nut bolt sml bus t3500 , tail lighy assy lh and rh sml bus t3500 , hardner tube for 1 kg putty , window glass with beading rear lhs sml bus t3500 , tie rod end set sml bus t3500 , drag link end set sml bus t3500 , side mirror lh and rh sml bus t3500 , hub oil seal rear inner and outer sml bus t3500 , hub oil seal front inner and outer sml bus t3500 , meter pannel cover sml bus t3500 , universal joint uj cross sml bus t3500 , accelerator cable sml bus t3500 , body solder putty , nc putty fine grey , fevi quick 10ml , m seal , fix bond adhesive tube small , thermostate valve sml bus t3500 , shackle suspension bush kit sml bus t3500 , lower clutch push rod sml bus t3500 , rubber beading set for doors sml bus t3500 , brake master cylinder with booster sml bus t3500 , oil cooler assy with packing sml bus t3500 , oil pump sml bus t3500 , fuel feed pump with packing sml bus t3500 , fip packing sml bus t3500 , by pass housing packing sml bus t3500 , hose pipe set sml bus t3500 , door trim pad rhs sml bus t3500 , engine mounting sml bus t3500 , radiator mounting sml bus t3500 , wheel cylinder assy sml bus t3500 , wheel brg front inner outer sml bus t3500 piston set std tata safari storme model2018 , sleeve cylinder set tata safari storme model2018 , piston ring set tata safari storme model2018 , main bearing set 10 tata safari storme model2018 , big end bearing set 10 tata safari storme model2018 , c r bush set tata safari storme model2018 , valve set inlet and exhaust tata safari storme model2018 , thrust washer set tata safari storme model2018 , valve seal inlet exhaust tata safari storme model2018 , engine oh kit complete tata safari //bid details2 / 71
Tender For supply of premium heavy-duty 22218 sphericalrollerbearing (taper bore k, c3 clearance) of make:- fag 22218-e1-xl-k / skf 22218 ek/c3 / rexnord-link-belt 22218lbkc0; [ warranty period:30 months after the date of delivery ]
Tender For supply of double row sphericalrollerbearing no. with rib 22214cc w33 c3(70*125*31) withc3 clearance, size: inner diameter 70mm x outer diameter 125mm x width 31mm, cage: steel cage with rib, detail as per annexure make: fag/skf/nbc/ntn/arb or equivalent as per given specification. gem consignee- sh harish katare (sse/mcc/cmlr) [ warranty period: 30 months after the date of delivery ]