Get complete information related to latest Spool Valve Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Spool Valve Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Spool Valve Tenders.
Tender For bid to ras bid to ras supply of compressor block with head and valve , piston and ring of air compressor , connecting rod with bearing , air filter , motor pully , oil seal , starter for three hp motor l andt , power supply board zero four eight seven six three one to eight eighty esab model no tig twenty two hundred i , micro switch for washing unit , protective lens for laser engraving machine f theta lens , protective lens for laser cleaning machine protective window or lens , cutoff switch sixty three amp of sixty three kva generator , copper lug twenty five mm , copper lug sixteen mm , insulation tape sixteen mm twenty five mtr , change over switch hundred amp , contactor aux point two no plus two nc coil voltage two twenty v seventy amp , amp meter zero to hundred ampt with ct , volt meter zero to five hundred volt , electronic timer zero to sixty sec , over load relay zero to forty amp
Tender For supply of set of spares such as 5/2 way single solenoid valve, electrical push button, electronic timer spdt and smps for pressurized flushing system fitted into indian railway lhb coaches as per annexure-a [ warranty period: 30 months after the date of delivery ]
Tender For supply of flushing switch assembly ( 5/2 spoolvalve type ) pneumatic operated sp ecification 1. operating air pressure = 10 bar (maximum) 2. 5/2 spoolvalve type (5 port 2 posi tions) as under (a) - total port = 5 nos. (b) - inlet port = 1 no., depth : 10 mm. to 12 mm., threa d diameter : 1/8 inch or 1/4 inch. (c) - outer post = 2 nos, depth : 10 mm. to 12 mm., thread dia meter : 1/8 inch or i/4 inch (d) - exhaust port = 2 nos., depth : 12 mm. to 15 mm, thread diamete r : 1/8 inch or i/4 inch (e) - total length of flushing switch assembly (without knob plates) is = 130 mm. (approximately). [ warranty period: 30 months after the date of delivery ]
Tender For bid to ras supply of brake pad front change , brake shoe rear change , front caliper assy change , rear brake drum , ignition coil change , spark plug change , realy change , plug wire change , electronic injector repair , seat adjuster , horn assy change , steering assy , the above mentioned parts removing the veh and all reqires portion service and all new parts fitting, engine tuning electrical check and wheel alignment and balancing , rotary pump assy and feed pump removing the veh and taken to the pump house and stripping all parts and cleaning checking. injector nozzle , pump full service and assembles above mentioned burned and damaged change and full packing change nozzle fitting injector , feed pump service with kit vehcile overbeating and produce white smoke. engine required for overhauling , engine liner set change , piston change , main bearing change , bigend bearing change , thrust washer change , piston ring change , valve inlet and exhaust change , valve guide change , head gasket change , gasket kit change , crunk shaft seal change , water pump change , engine mounting pad change , oil filter change , air filter change , fuel filter change , fan belt change , timing belt change , timing tensoner change , clutch plate change , pressure plate change , release bearing change , fly wheel skimming change , fly wheel bearing change , hub seal inner and outlet change , annabond paste , radiator hose set change , front brake pad change , rear brake shoe change , suspension bush kit change , radiator repair and service , self and alternator repair and service. lathe machine works , engine bore boring and new liner fitting and boning and finishing and piston seting , crank shaft main and both bearing setting , cylinder head stripping, cleaning and old valve guide, removing and new guide fitting and valve seat, grinding, vlave fixing and head assy and pressure testing , engine assy removing the veh and stripping and cleaning all parts and engine assy and mounting the veh and self, alternator raditor fitting and veh started testing cooling labou charge , electrical system checking and wheel alignmnet and balancing , timing shain kit change , brake shoe front and change , chain sprocket kit change , kiker change , engine bore reboring, boning and finishing , the above mentioned all parts removing and new parts fitting labour charge , self starter ssy repair service with unservicable parts change, field coil, armature soldering and brush holder and brush change