Latest structural angle Tenders | Government structural angle Tenders

State Government

CTN :43467490

13 Jan, 2026 NA

Delhi - Delhi

Tender For s/i/t/c of e/m equipments and allied works for newly re-bored tube well at okhla vihar near majar in okhla constituency ac-54. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 15 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point: 200-125-75 lpm on 89-124-133 mtr. head.having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved. , supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted. a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no. b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 no c) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no. e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable banking g) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos.complete wiring &installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated and pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs. make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., supply of ms nut bolts off size as per requirement., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 1x1 made out from 6mm thick m.s. sheet in 2 halves and a circular hole in centre 3-1/2 dia. with locking arrangement by nuts and bolt. , earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.

corporations/Associations/Others

CTN :43521829

20 Jan, 2026 NA

Multi City - Multi State

Tender For supply of m6x20mm counter sunk machine screw flat head ss bolt , angle cock for health faucet ss , m s cut off wheel 5 inch size of bosch or yuri make , grinding wheel 4 inch dia bosch make , abrasive flap disc of size 100mmx16mm , 4mm hss straight shank jobber drill bit , gi wire 18 gauge galvanised iron , hss drill bit of 3 mm dia of bosch make , s s hinges of size 3 inch

Central Government/Public Sector

CTN :43521633

19 Jan, 2026 NA

Multi City - Multi State

Tender For supply of angle 50 x 50 x 6 mm, e250 gr-a, is2062 , angle 65 x 65 x 6 mm, e250 gr-a, is2062 , angle 65 x 65 x 8 mm, e250 gr-a, is2062 , angle 75x75x6, e250 gr-a, is2062 , angle 130x130x12, e250 gr-a, is2062 , angle 90x90x6, e250 gr-a, is2062 , angle 90x90x8 mm, e250 gr-a, is2062 , angle 110x110x12 mm, e250 gr-a, is2062 , ismc 75 x 40 mm, e250 gr-a, is2062 , ismc 100 x 50 mm, e250 gr-a, is2062 , m s flat 50x6, is2062 , ismc 125 x 65 mm, e250 gr-a, is2062 , ismc 150 x 75 mm, e250 gr-a, is2062 , ismc 200 x 75 mm, e250 gr-a, is2062 , ismc 250 x 82 mm, e250 gr-a, is2062 , ismc 300 x 90 mm, e250 gr-a, is2062 , ismb 125 x 70 mm, e 250 gr-a, is2062 , ismb 200 x 100 mm, e250 gr-a, is2062 , ismb 250 x 125 mm, e250 gr-a, is2062 , ismb 300 x 140 mm, e250 gr-a, is2062 , ismb 350 x 140 mm, e250 gr-a, is2062 , npb 400x180x66.3 is 2062 e250 gr-a , npb 450x190x92.4 is 2062 e250 gr-a , npb 500x200x90.7 is 2062 e250 gr-a , cq pl 6 mm is 3502 6 x 1250x6300 as per tdc 6 386 , pl 8 mm is 2062 e250 br k tdc 6 386, width 2500mm, length 12000mm 8 x 2500 x 12000 , pl 10 mm is 2062 e250 br k tdc 6 386, width 2500mm, length 12000mm 8 x 2500 x 12000 , pl 10 mm is 2062 e350b0 k tdc 6 386, width 2500mm, length 10000mm 10 x 2500 x 10000 , pl 12 mm is 2062 e350b0 k tdc 6 386, width 2500mm, length 12000mm 12 x 2500 x 12000 , pl 16 mm is 2062 e350b0 k tdc 6 386, width 2500mm, length 12000mm 16 x 2500 x 12000 , pl 20 mm is 2062 e350b0 k tdc 6 386, width 2500mm, length 12000mm 20 x 2500 x 12000

State Government

CTN :42900968

12 Jan, 2026 NA

Haldwani - Uttarakhand

Tender For bid to ras corrigendum : supply of steel rule,try square,caliper inside spring type,caliper hermaphrodite spring type,caliper outside spring type,divider spring type,scriber,centre punch,screw driver,chisel cold flat,hammer ball peen with handle,hammer ball peen with handle,file flat second cut,file flat smooth,file half round second cut,hacksaw frame fixed type,safety goggles,dot punch,steel rule graduated both in metric and english unit,straight edge steel,spirit level metal,stud extractor ezy out,combination set,micrometer outside,micrometer outside,micrometer outside,micrometer inside with extension rods,vernier caliper,vernier height gauges,vernier bevel protractor,screw pitch gauge metric,wire gauge metric standard,surface plate granite with stand and cover,marking table mild steel,universal scribing block,v block pair with clamps,angle plate,punch letter set,punch number set,portable hand drill electric,drill twist straight shank,drill twist taper shank,taps and dies complete in box,taps and dies complete,file knife edge smooth,file fea

State Government

CTN :43496843

16 Jan, 2026 21.23 Lacs

Bengaluru - Karnataka

Tender For tender for the procurement of irdm & mechanical sector toolkits for sc & st trainees - tlk-safety helmet , tlk-safety apron, tlk-tool kit box , tlk-triangular file 2nd cut, tlk-multiple slip joint plier, tlk-hammer ball peen , tlk-hacksaw frame , tlk-lineman plier, tlk-tlk-file flat 2nd cut, tlk-file flat bastard, tlk-file flat smooth, tlk-file half round 2nd cut, tlk-center punch , tlk-chisel cold flat, tlk-c clamp, tlk-digital multimeter, tlk-double ended spanner, tlk-engineer try square, straight shank twist drill bit set, tlk-auto-darkening welding glasses, tlk-adjustable spanner, tlk-angle grinder, electrician screw driver , hand drilling machine electric portable , hexagonal allen key set , needle files , neon tester , tlk-combination plier, tlk-file square 2nd cut, tlk-steel rule , tlk-welding hand gloves, heavy duty screw driver

Co-operative

CTN :43429122

13 Jan, 2026 2.57 Lacs

Dakshina Kannada - Karnataka

Tender For corrigendum : supply of s.s materials to mangalore dairy - s. s 304, angle, 50mm x 50mm x 6mm, s. s 304, angle, 40mm x 40mm x 6mm, s. s 304, angle, 25mm x 25mm x 6mm, s. s square tube, 40mm x 40mm x 1.5mm, s. s square tube, 50mm x 50mm x 1.5mm, s. s 304 solid round rod, 32mm, s. s 304 solid round rod, 20mm, s. s 304, washer, 8mm, s. s 304, bolt nut, 40mm x 8mm, s. s 304 pipe, sch10, 25mm, s. s 304 pipe, sch40, 20mm, s. s 304 pipe, sch10, 15mm, flat s. s 304, 40mm x 6mm, flat s. s 304, 40mm x 4mm

CTN :43206566

12 Jan, 2026 NA

Ferozepur - Punjab

Tender For corrigendum : material and labour for construction of 3800 mtr x chain link fence in ferozepur - s&f structural steel post of angle iron 65x65x6mm, 4.50 mtr long, weight as per is 2062-1984 including fabrication of 0.60 mtr both side long top portion swan neck v type at 30 degree to vertical, including making six round holes of 15 mm dia on vertical posts and for fixing of nuts and bolts and three nos of 15 mm dia holes for fixing strut and five nos notches on the swan neck and welding of two nos of 16 mm ms rod each of 0.23 mtr length to bottom end of picket for anchorage including one coat of red oxide primer and two coat of synthetic enamel paint for exposed surface of angle above gl complete and two coat of bituminous paint embedded portion of angle 0.45mtr. make : jindal/ sail/ tata/equivalent isi marked complete all as specified and directed by engineer-in-charge, s&f structural steel post of angle iron 65x65x6mm, 3.30 mtr long, weight as per is 2065- 1984+b12, including fabrication for strut post bending at top portion, including making three nos holes of 15 mm dia on vertical posts for fixing of nuts and bolts and three nos of 15 mm dia including 0.23 mtr 16 mm dia ms rod two piece to be welded at bottom for anchoring purpose including one coat of red oxide primer and two coat of synthetic enamel paint for exposed surface of angle above gl complete and two coat of bituminous paint for stud 0.45mtr below gl for one side of the post complete all as specified and directed by engineer-in-charge. make : jindal/ sail/ tata/equivalent isi marked, s&f galvanised two or three strand steel barbed wire (line wire) of 2.24mm diameter of wire, barbs at 75mm spacing. the barbs are (point wire) 02mm thick wire shall be isi marked as per is:278 of 1978 (third revision) with amdt no 1 to 4. the points of barbs shall be sharp. the line and point wires shall be circular in section free from scales and point wires shall be circular in section free from scales and defects and shall be uniformity galvalium. the barbed wire shall be manufactured as per clause 11.2.1 and 11.2.2 respectively of is specification cited above read with is 4826/79 (first revision).make:sail/tata/ aplapollo/rinl/jsw complete all as specified and directed by engineer-in-charge, s&f galvanised steel chain link fence fabric of mesh size 125mm x 125mm (+/-) 4mm of 4.00mm nominal diameter. the size of chain link fence fabric shall be 2.7 mtr x 15 mtr mesh wire. galvalium chain link shall be manufactured as per is 4823 complete all as specified and directed by engineer-in-charge. make : tata/jsw/rinl/ jindal/sail., s&f ms plat of 40x3 mm, 2.70 mtr long with 6 holes of 15 mm dia, including one coat of red oxide primer and two coats of synthetic enamel paint. 3.02 kg per flat. make of steel: jindal/ sail/ tata/equivalent isi marked complete all as specified and directed by engineer-in-charge., s&f mild steel bolts with hexagonal head at one end and screwed the other end fitted with one nut and two washers. the bolts shall be 12mm dia and 50mm long. strong long lasting, resistant to corrosion and 100% recyclable complete all as specified and directed by engineer-in-charge. make: jindal / sail/ tata/ apl apollo/ jsw/ rinl, s&f ms round bars 10mm dia with hook on both sides made to shape including two coats of synthetic enamel paint over a coat of red oxide primer. make: jindal/ sail/ tata/ apl appolo/ jsw/ rinl complete all as specified and directed by engineer-in-charge., s&f ms round bars 16mm dia with hook on both sides made to shape including two coats of synthetic enamel paint over a coat of red oxide primer make: jindal/sail/tata/apl apollo/jsw/rinl complete all as specified and directed by engineer-in-charge., material and labour for excavating in soft and dense soil trenches, exc 1.5 m wide and exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and exc 1.5 m in dept

CTN :43502583

19 Jan, 2026 NA

Wardha - Maharashtra

Tender For supply of steel bar carbon hot rolled squre 16mm , steel bar carbon hot rolled flat 50 x 6 , leaded brass rod round 16mm , angle ms long 6ft , post fence metal angle

CTN :43502930

19 Jan, 2026 NA

Gandhinagar - Gujarat

Tender For supply of windows handles 150mm left hand , oil putty , peg set 300 mm for ms , ptmtjet spray with 1 mtr tube , pvc ball cock float valve 50mm complete , pvc swr pipe 75mm dia , pvc bath cabinate 350 x 450 mm , pvc bathroom water shower 100mm , pvc connection 15x450mm long complete with nut bolt and washer , pvc connection 15x600mm long complete with nut bolt and washer , pvc cover suitable for all water storage tank 500 ltr complete , pvc flushing cistern 10 ltr cap , pvc grating 100mm , pvc grating 75mm , pvc swr pipe 110mm dia , pvc tee equal 110mm , pvc washer suitable 15mm bore bib tap , pvc waste coupling 40mm , pvc waste pipe corrugated 32 x 900 mm long , ss curtain bracket 25 mm dia , steel screw 25mm x 8g , steel screw wood 45mm x 8g , steel ms hinges butt 75 mm , urinal flat back 450 x 350 x300mm , whb 550x450x440mm , cp overhead shower , pvc water storage tank with lid 1000 ltr , bell joint repair clamp for di pipe 100 mm , gi plug 40mm , gi plug 50mm , di pipe k7 100 mm both end flange , di pipe k7 fitting tee 100 mm both end flange , bell joint repair clamp for ci pipe 100 mm , bell joint repair clamp for ci pipe 150 mm , bell joint repair clamp for ci pipe 200 mm , bell joint repair clamp for di pipe 150 mm , bell joint repair clamp for di pipe 200 mm , gate valve gun metal 50mm , gi socket screwed 50mm , copper sulphate , gate valve gun metal 15mm , eco clean 2300 herbal reagent 1 ltr , gate valve 25mm , gi bend 90 deg 20mm , gate valve gun metal 40mm , cpvc coupler 20mm , cpvc elbows 40mm , cpvc male thraded 20mm , gate valve gun metal 20mm , gi elbow 15 mm , gi socket 15mm , gi union 15mm , bleaching powder , cpvc elbows 20mm , cpvc female thraded 20mm , cpvc female thraded 32mm , cpvc female thraded 40mm , cpvc male thraded 32mm , cpvc male thraded 40mm , cpvc tee 20mm , cpvc tee 40mm , cpvc union 20mm , cpvc union 32mm , cpvc union 40mm , gate valve gun metal 25mm , gi socket 25mm , gi socket 20mm , gi union 20mm , cpvc valve 32 mm , cpvc valve 25 mm , cpvc coupler 32mm , cpvc male thraded 25mm , cpvc reducer socket 32x25mm , round up herbisite 1 ltr , m seal 150 gm , gi union 25mm , liquid defoaming agent , sodium hypoclorite solution , alum ferric solution , calcium hypochlorite , astronomical time switch based on lux level , bell ding dong call bell , cable copper flexible 3 core x2 point 5 sqmm , cable lugs alumn 120 sqmm , cable lugs alumn 150 sqmm , cable lugs alumn 185 sqmm , cable lugs alumn 240 sqmm , cable lugs alumn 25 sqmm , cable lugs alumn 300 sqmm , cable lugs alumn 35 sqmm , cable lugs alumn 50 sqmm , cable lugs alumn 70 sqmm , cable lugs alumn 95 sqmm , cable lugs ring type 100 sqm , cable lugs ring type 120 sqm , cable lugs ring type 150 sqm , cable lugs ring type 240 sqm , cable lugs ring type 25 sqm , cable lugs ring type 300 sqm , cable lugs ring type 35 sqm , cable lugs ring type 40 sqm , cable lugs ring type 50 sqm , cable lugs ring type 70 sqm , cable lugs ring type 95 sqm , cable lugs u type 10 sqmm , cable lugs u type 16 sqmm , capacitor 2 point 5 mfd , engine oil , batton holder , angle holder lamp batten bakelite , ht do fuse 10 amp , ht tape element 11 kv voltage grade insulation , led 9 watt bulb 6500k , led bulb 12 w , led street light 60 w , led street light 70w , led 2x 2 36watt led fitting , ht11 kv cold shrink indoor type cable end joint 95 sqmm , ht11 kv cold shrink outdoor type cable end joint 95 sqmm , ht 11 kv cold shrink straight through joint 95 sqmm , pvc tape roll 40 mm , spn db box 4 way , brass mortice lock four lever //bid details 2 / 125 vertical type , lock 6 lever 100 mm brass , paint se black 1 ltr pack , paint brush 25 mm , paint brush 50 mm , paint brush 75 mm , paint synthetic enamel og in 1 ltr pack , paint white 1 ltr pack , soft broom with grass , tarpentine

CTN :43521730

30 Jan, 2026 NA

Multi City - Multi State

Tender For supply of n1 1015001999 guard , n1 5340135266 clamp lower , n1 4010000915 chain welded , n1 5365010085 ring retaining , n1 5365010140 ring retaining , n1 5360007205 spring helical compression , n1 5340014956 block locating , n1 5307001295 stud saddle , n1 5365010651 ring externally threaded , n1 ifl7959 shaft , n1 5310001510 nut adjusting , n1 1015000451 segment bevel wheel , n1 5340004285 fork end , n1 5340015504 plunger detent , n1 5340003359 clamp , n1 5360007181 spring leaf , n1 5365001654 spacer ring , n1 5310001502 washer , n1 5365010555 bushing machine thread , n1 1015000231 shaft actuating breech block , n1 3110002901 race lower , n1 5330002288 ring expanding u packing , n1 4010000914 chain welded , n1 5340175282 grip handle , n1 5310001647 washer spring conical , n1 5310237190 washer flat , n1 6680000480 dip stick liquid quantity , n1 4010000916 chain welded , n1 1015000477 ring wheel assy , n1 5340014793 bracket angle , n1 1015000337 cap retainging guide gush upper , n1 1015000477 brake packing , n1 5340014793 cap , n1 1015000337 washer , n1 1015000389 hinge , n1 5310001484 washer lock , n1 5970002854 insulation sleeving electrical , n1 3120104751 bearing sleeve , n1 5330002289 ring , n1 5340015631 bracket angle , n1 5305007851 screw socket head , n1 5330023702 gasket , n1 5305007849 screw machine , n1 5305003151 thumb screw , n1 5340015629 cover protective dust moisture seal , n1 1015002034 stub axle right axle assy , n1 5360007197 spring helical compression , n1 4030000493 shakle , n1 1015000652y bush , n1 ina0369cn gear wheel n13020002796 and gear bevel n13020002789 , n1 ifl7992 soacer , n1 5330024796 packing preformed , n1 5305003164 screw externally relieved body , n1 5340016902 cover protective dust and moisture seal , n1 3040003337 shaft straight , n1 5306030064 bolt machine , n1 5330024789 packing preformed , n1 5315000975 pin , n1 5365010558 bushing rubber , n1 1015000367 bracket , n1 4730006971 adapter st right pipe to hose coupling , n1 5307001296 stud stay gun , n1 2530004729 adjuster slak brake , n1 5120003115 spanner 43a , n1 2530001013 hose , n1 5310001535 washer lock , n1 5360007188 spring helical compression , n1 5310002391 washer recessed , n1 4933000318 plane setting cutoff gear //bid details 2 / 53

Structural Angle Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

corporations/Associations/Others

Central Government/Public Sector

State Government

State Government

Co-operative