Get complete information related to latest Swivel Bearing Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Swivel Bearing Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Swivel Bearing Tenders.
Tender For supply of procurement of acs and sgci rolling mill work rolls d d -2003655 , 2003690 , 2003708 , 2003717 , 2003733 , 2003734 , 2003736 , 2003737 , 2003738 , 2114152 roll material alloy cast steel hardness 40-45 shore c drawing reference 1-d22939,rev-c tensile strength 85 to 100 kgf/mm stand no billet mill 1 & 2 size 850 x 1200 mm barrel hardness 40-45 shc roll approximate unit weight 7. 35 tons uts 85-100 kgf/sq. mm neck hardness 40-45 shc neck runout 0. 04 mm roll coating anti-corrosive ring hardness 600-700 hv3 test certificate required yes ring drawing no mec/1/22938/rev c ---------------------------------------- special instructions: ---------------------------------------- 1) ultrasonic,uts & elongation tests shall be done and certified. 2) flat wobblers to be strictly concentric with roll neck journals. 3) rolls to be suitably packed and numbered for identity. 4) the microstructure should be free from continuous network of carbides along the grain boundaries. 5) t. c. to be given along with micro-structure photograph. a seperate copy to be sent to d. g. m(rs&rs) at the time of delivery. 6) the rolls shall be guaranteed against manufacturing defects such as blow holes, cavity, non-metallic inclusions, pipe segregation,cracks,hard spots, flakes etc which may adversely affect their service life. 7) should any roll fail prematurely or give sub-standard performance due to the above defects, the suppliers shall rectify the defects at their cost wherever possible to the entire satisfaction of vsp or make prorata compensation or make full replacement if the roll has been rejected before use. 8) the rolls are also to be guaranteed for the roll life as mentioned or 5 ) /bid number: gem/2026/b/7117383 * /dated: 23-01-2026 & & / bid document1 / 23years from the date of supply to vsp which ever is earlier. this guarantee clause superseeds, guarantee mentioned elsewhere in the po(a/t), in this regard. 9) hardness test of end ring shall be done and certified. 10) these rolls are used in roughing stands of hot rolling mill. , roll material sg cast iron (accicular) hardness 70-75 shore c drawing reference 1/4012885,rev-e stand no bar mill 19 & 21 size 360 x 600 mm barrel hardness 70-75 shc roll approximate unit weight 0. 70 tons neck hardness 38-45 shc neck run out 0. 04 mm roll coating anti-corrosive coating drop in hardness 1 shc per 10mm on barrel depth -----------------------------------special instructions: ------------------------------------ 1) flat wobblers to be strictly concentric with roll neck journals. 2) rolls to be suitably packed and numbered for identity. 3) t. c. to be given along with micro-structure photograph. a seperate copy to be sent to d. g. m(rs&rs) at the time of delivery. 4) the rolls shall be guaranteed against manufacturing defects such as blow holes, cavity, non-metallic inclusions, pipe segregation,cracks,hard spots, flakes etc which may adversely affect their service life. 5) should any roll fail prematurely or give sub-standard performance due to the above defects, the suppliers shall rectify the defects at their cost wherever possible to the entire satisfaction of vsp or make prorata compensation or make full replacement if the roll has been rejected before use. 6) the rolls are also to be guaranteed for the roll life as mentioned or 5 years from the date of supply to vsp which ever is earlier. this guarantee clause superseeds, guarantee mentioned elsewhere in the a/t, in this regard. these rolls are used in hot rolling mill, roll material sg cast iron (accicular) hardness 70-75 shore c drawing reference 1-4012884,rev-d stand no bar mill 20 & 22 size 360 x 600 mm barrel hardness 70-75 shc roll approximate unit weight 0. 70 tons neck hardness 38-45 shc neck run out between centres 0. 04 mm roll coating anti-corrosive coating drop in hardness 1 shc per 10mm on barrel depth ------------------------------------ special instructions: ------------------------------------ 1) fla
Tender For supply of , counter balance valve seal kit , teflon boom pulleys thickness 10mm , pulley pin bush 04 nos x 02 nos of cranes , pulley pin 01 nos x 01 nos of cranes , teflon packing plates 02 nos x 02 nos of cranes , teflon elbow plates 02 nos x 02 nos of cranes , teflon sq plates 02 nos x 02 nos of cranes , telescopic cylinder seals 01 st x 02 nos of cranes , shaft wiper seal 01 nos x 02 nos of cranes , mechanical or penalty brake seal kit 01 nos x 02 nos of cranes , hydraulic motor pressure plate 01 set x 02 nos of cranes , hydraulic motor seal set 01 nos x 02 nos of cranes , boom counter balance valve seal kit 02 nos , cylinder seals 01 set x 02 nos of cranes , pressure plate of motor 01 nos x 02 nos of cranes , hydraulic motor seal kit 01 nos x 02 nos of cranes , pressure plate 01 nos x 02 nos of cranes , seal kit set 01 nos x 02 nos of cranes , hook safety lock 9 point 5 tons 01 nos x 02 nos of cranes , wire rope guide pin 01 nos x 02 nos of cranes , winch seal kit 01 nos x 02 nos of cranes , planetary gear box roller pin 180 nos x 02 nos of cranes , gear box seal kit 01 nos x 02 nos of cranes , mechanical clutch plates set 01 nos x 02 nos of cranes , shaft seal 04 nos x 02 nos of cranes , return line filter 01 nos x 02 nos of cranes , hydraulic hose pipe alongwith end connector with 90 deg bend and benjo e , hydraulic hose pipe wp 275 bar alongwith both end st connector , hydraulic hose pipe wp 270 bar alongwith both end st connector , hydraulic hose pipe wp 270 bar alongwith end connector with 90 deg ben , oil breather size 2 and half inch , oil indicator 10 inch , pressure gauge range 0 to 400 bar , hydraulic hose pipe alongwith end connector with 120 deg bend and st , hydraulic hose pipe alongwith end connector with 90 deg bend and st , hydraulic hose pipe alongwith both end st connector , hydraulic hose pipe alongwith end connector with 90 deg and st , hydraulic hose pipe alongwith both end st connector , hydraulic hose pipe alongwith end connector with st and benjo eye 3 by 4 inch , hydraulic hose pipe alongwith end connector with benjo eye and st , pulley bearing 04 nos x 02 nos of cranes , winch shaft bearing , hydraulic motor bearing 02 nos x 02 nos of cranes , swivelbearings 02 nos x 02 nos of cranes , bearings 02 nos x 02 nos of cranes , hook pulley bearings 02 nos x 02 nos of cranes , drive gear shaft bearing 03 nos x 02 nos of cranes , universal coupling bearing 08 nos x 02 nos of cranes , 2nd stage bearings 06 nos x 02 nos of cranes , clutch plate bearing 02 nos x 02 nos of cranes , swing motor shaft bearing 02 nos x 02 nos of cranes , bearing shaft 02 nos x 02 nos of cranes , wire rope , accumulator cylinder relief seal kit , load jumping cylinder counter balance valve seal kit , wire rope cylinder counter balance valve seal kit , wire rope pulley jumping cylinder seal kit , load jumping cylinder seal kit , main boom mounting cylinder teflon bush , seal kit for the hydraulic cylinder main boom , winch wiper seal , return line filter 1and 1 by 4 inch , winch seal kit , winch hydraulic motor seal kit , 10 mmx 10 mm x 1100 mm st x 90 high pressure hose pipe , 10 mm x 10 mm x 700 mm st x 90 high pressure hose pipe , 16 mm x 16 mm x 800 mm st x 90 high pressure hose pipe , 16 mm x 16 mm x 600 mm st x 90 high pressure hose pipe , 16 mm x 16 mm x 1000 mm st x st high pressure hose pipe , 20 mm x 20 mm x 1000 mm st x st high pressure hose pipe , suction hose pipe 2and half inch x 1500 mm length , 10 mmx 10 mm x 1500 mm st x st high pressure hose pipe , 20 mm x 20 mm x 1000 mm st x st high pressure hose pipe , 10 mm x 10 mm x 1000 mm st x 90 high pressure hose pipe , 10 mm //bid details 2 / 123 x 10 mm x 1400 mm st x 90 high pressure hose pipe , 10 mm x 10 mm x 500 mm st x st high pressure hose pipe , 1by4 x 10 mm x 900 mm st x st high pressure hose pipe , seal kit of relief and flow control valve of pump , emergency hand pump seal kit , oil level indicator , pressure gauge 6000 psi , wire rope pulley pin 600 mm x 60
Tender For supply of hydraulic cyl hm 110 qty d d - tube as per sample_drg with oparation of turning inner dia_ grinding and horning steel tube 60_3 mm od x 48 mm id st 52 _din 2391_ , steel round 36 mm dia is _ 1570 c20 _7_2 mtrs_ , steel round 65 mm dia is _ 1570 c40 _10 mtrs_ , piston rod 25 mm dia x 558 mm long turning_ hard thread cutting_ hard chrome plating and grinding as per drg steel round 25 mm dia ck 45 _din 17200_ , steel round 50 mm dia bright turning and nickel plating as per drg is _ 1570 c40 , steel round 62 mm dia is _ 1570 c40 _3_6 mtrs_ , steel round 60 mm dia bright turning milling and nickel plating as per drgis _ 1570 c40 , swivelbearing ge 25_es40 , nitrile rubber _o_ ring 44_04 mm id x 3_53 mm dia to be moulded with die , wear guide 30 mm od x 25 mm id x 9_7 mm thk as per sample_drg moulding with flame_retardant polymeric rubber , rod seal 33 mm od x 25 mm id x 5_7 mm thk as per sample_drg moulding with polyurethane rubber compound , wiper seal 33 mm od x 25 mm id x 5 mm thk as per sample_drg moulding with polyurethane rubber compound , piston seal 50 mm od x 39 mm id x 4_2 mm thk ptfe with nitrile rubber as per sample_drg to be moulded with die , wear guide 50 mm od x 45 mm id x 5_5 mm thk as per sample_drg bronze bush with ptfe coating inner surface , nitrile rubber _o_ ring 19 mm id x 3_0 mm dia to be moulded with die , steel nylock nut m16 x 1_5 mm is _ 7002_2005 , welding rod 3_15 mm dia x 350 mm long , paint primer redoxide ) /bid number : gem/2025/b/6987012 * /dated: 24-01-2026 & & / bid document 1 / 19
Tender For corrigendum : supply of various valves and their spare at dm plant and cpu regeneration for 500 mw unit no.6, utps.(bmd-6 et-6171) - ball valve size:15 mm,150 screwed end to npt f full bore 2 piece const lever operated, ss-316, astm a 351 gr. cf8m, ball valve, size: 25mm, 3 piece design, full bore, renewable teflon seat & seal, fitted with ss316 internal working parts, flanged ends, asa- 150 class., ball valve size:65 mm,150 raised flanged drilled to ansi b16.5 full bore 2 piece const lever operated, ball valve size:80 mm,150 raised flanged drilled to ansi b16.5 full bore 2 piece const lever operated, butterfly valve 50 nb, lever operated, ss body, used for caustic/acidic line at dm plant of unit6-utps., butterfly valve, nb 65, lever operated, ss body, used for caustic/acidic line at dm plant of unit6-utps., butterfly valve 100 nb, lever operated, ss body, used for caustic/acidic line at dm plant of unit6-utps., butterfly valve nb 125, lever operated, ss body, used for caustic/acidic line at dm plant of unit6-utps., butterfly valve 150 nb lever operated, ss body, used for caustic/acidic line at dm plant of unit6-utps., butterfly valve 50 nb (double acting), air operated, ss body, used for caustic/acidic line at dm plant of unit6-utps., butterfly valve, nb 65 (double acting), air operated, ss body, used for caustic/acidic line at dm plant of unit6-utps., butterfly valve nb 80 (double acting), air operated, ss body, used for caustic/acidic line at dm plant of unit6-utps., butterfly valve nb 100 (double acting), air operated, ss body, used for caustic/acidic line at dm plant of unit6-utps., butterfly valve, nb 200 (double acting), air operated, ss body, used for caustic/acidic line at dm plant of unit6-utps., diaphragm valve size 25 nb metal: cast iron., rubber lined diaphragm valve size 40 mm, rubber lined diaphragm valve size 50 mm (2), novel make, metal: cast iron., rubber lined diaphragm valve size 65 mm (2 ) novel make, metal cast iron., diapharm valve 80mm, rubber lined diaphragm valve size 100 mm (4), novel make, metal: cast iron., 40 nb double acting pneumatic diaphragm valve with flange end,actuator model 1018d/a,moc cirl,pn-10, 50 nb double acting pneumatic diaphragm valve with flange end,actuator model 1018d/a,moc cirl,pn-10, 65 nb double acting pneumatic diaphragm valve with flange end,actuator model 1035d/a,moc cirl,pn-10, 80 nb double acting pneumatic diaphragm valve with flange end,actuator model 1001d/a,moc cirl,pn-10, 100 nb double acting pneumatic diaphragm valve with flange end,actuator model 1002d/a,moc cirl,pn-10, 25 nb ball valve with flange end ,actuator model b52da, cl150, moc cf8m/ss316, 100 nb ball valve with flange end,actuaor model b125da,pn10,moc-cf8m/ss316, seal kit for 50 nb bfv consist of seat in epdm,o ring in viton and bearing ptfe, seal kit for 80 nb bfv consist of seat in epdm,o ring in viton and bearing ptfe, seal kit for 100 nb bfv consist of seat in epdm,o ring in viton and bearing ptfe, seal kit for 150 nb bfv consist of seat in epdm,o ring in viton and bearing ptfe, seal kit for actuator b52da consist of o ring,guide bands,bushes,circlips and washer, seal kit for actuator b83da consist of o ring,guide bands,bushes,circlips and washer, seal kit for actuator b83sr consist of o ring,guide bands,bushes,circlips and washer, seal kit for actuator b125da consist of o ring,guide bands,bushes,circlips and washer, seal kit for actuator b140da consist of o ring,guide bands,bushes,circlips and washer, complete valve assembly for 65 nb globe valve, cs globe valve class-150,80 nb (3"), ci check valve size 65 mm (nrv), ccs swing check non return valve 150,80 nb (nrv), non return valve (nrv) 100 mm 150