Tender For ridf xxviii - lift irrigation projects in various padashekharams of wayanad district- procurement of submersible pumpsets, fittings, accessories, and related electrical works - procurement, installation, erection, testing, and commissioning of pumpsets and allied works at punchavayal, manikkuni, kolembetta, valiyavattam, and padiyeri pumphouses. - procurement, installation, erection, testing, and commissioning of pumpsets and allied works at punchavayal, manikkuni, kolembetta, valiyavattam, and padiyeri pumphouses., supply, installation, erection, testing, commissioning and fitting charges for all accessories of horizontally mounted submerged centrifugal non clog pump set of compact unitary mono-block submerged single/multi stage,volute type casing with suitable radial type impellers on common shaft for pump and motor ,anti friction bearing with life time greasing, protection features with sensors to monitor temperature,mechanical seal leakage ,etc.(the pump should be confirming to his/is standards).the moc of pump,casing-cast iron,impeller -ss cf8m,shaft-ss-316,suction strainer -ss and other as per is standard.the motor should be suitable for 3 phase,415v /-10%,50hz /5%,ac supply submersible motor having class f /h insulation, air filled and ip-68protection confirming to is 325 or latest standards suitable for day night operation.the pump discharge capacity of 230 cubic metre /hour against duty point head of 42 mtrs, working head range 18 - 47m, discharge range 136 - 57 lps ,speed 1450rpm(n) or nearer ,with 10meters of copper power cable and control cable, railing arrangement. the pump should be painted with three coats of suitable anti corrosive paint over priming coat. the electrical works for the pumpset should be completed as per kseb rules and regulations and the contractor is responsible for arranging premissions and certificates from the electrical inspectorate. the suction side of the pumpset should be provided with an additional iron grill for preventing foreign particles inside the inlet side of the pump casing., supply and erection of 60hp auto transformer starter (ats) with suitable incommer and contactors including 24 kvar capacitor with required indications ,metering and protections for single phasing ,overload, pump monitoring unit to protect from ingress, high temperature level etc enclosed in a closed panel board, supply and laying additional termination cable of 1.1kv 3.5 core 95sqmm aluminium conductor xlpe insulated ;steel armoured ug cable as per relevant is 7098 with support for cable, supply, installation, erection, testing, commissioning and fitting charges for all accessories of horizontzlly mounted submerged centrifugal non clog pump set of compact unitary mono-block submerged single/multi stage,volute type casing with suitable radial type impellers on common shaft for pump and motor ,anti friction bearing with life time greasing, protection features with sensors to monitor temperature,mechanical seal leakage ,etc.(the pump should be confirming to his/is standards).the moc of pump,casing-cast iron,impeller -ss cf8m,shaft-ss-316,suction strainer -ss and other as per is standard.the motor should be suitable for 3 phase,415v /-10%,50hz /5%,ac supply submersible motor having class f /h insulation, air filled and ip-68protection confirming to is 325 or latest standards suitable for day nightoperation.the pump discharge capacity of 188 cubic metre /hour against duty point head of 35 mtrs,working head range 16 - 42m, discharge range 102 - 42 lps ,speed 1450 rpm(n) or nearer ,with 10meters of copper power cable and control cable,railing arrangement. the pump should be painted with three coats of suitable anti corrosive paint over priming coat. the electrical works for the pumpset should be completed as per kseb rules and regulations and the contractor is responsible for arranging premissions and certificates from the electrical inspectorate. the suction side of the pumpset should be provided with an addition
Tender For supply of spares of single screw pumps installed at etp and pt plant unit 3 and 4, ctpp, chhabra - pump model eh-600 (cap.-10 m3/hr, pr.-2.2-2.7 kg/cm2, sr. no. u07276-79/9/12, comm.-111114). (qty.04 nos.) at transformer sump (moc and part no. are as per tender specification), stator, helical rotor, gland, distance bush, radial shaft seal ring, joint ring, cardon joint set (01 set=2 nos.), bearing housing, stuffing box housing, discharge branch, pump model eh-375 (cap.-8 m3/hr, pr.-1.5-2.5 kg/cm2, sr. no. u07273-75/9/12, and u07281-83/9/12, comm.-111114). (qty.06 nos.) at bfp and switchyard sump (moc and part no. are as per tender specification), drive shaft, stator, gland, cardon joint set (01 set=2 nos.), bearing housing, stuffing box housing, pump model eh-1024 (cap.-15 m3/hr, sr. no. u04846-47/3/11, comm.-110225). (qty.02 nos.) at centrifuge feed sump (moc and part no. are as per tender specification), stator, helical rotor, gland, circlip for bore, circlip for shaft, radial shaft seal ring, joint ring, cardon joint set (01 set=2 nos.), stuffing box housing, pump model e2h-164 (cap.-0.4m3/hr, sr. no. u04848-49/3/11, comm.-110225). (qty.02 nos.) at lime dosing (moc and part no. are as per tender specification), stator, helical rotor, joint shaft, drive shaft, bearing housing, circlip for bore, circlip for shaft, radial shaft seal ring, spring ring, spring ring, cardon joint set type-ao (01 set=2 nos.), joint ring, pump model eh-164 (cap.-1m3/hr, sr. no. u07240-41/9/12, comm.-111114). (qty.02 nos.)at chemical house ii (moc and part no. are as per tender specification), stator, helical rotor, joint shaft, drive shaft, circlip for bore, circlip for shaft, radial shaft seal ring, spring ring, spring ring, cardon joint set type-ao (01 set=2 nos.), joint ring
Tender For tender for supply of circlip , woodruff key a10x16 part nopoint05673 , doublepointslpointoil contpointring 80 part nopoint 06369 , valve plate comppointpart nopoint07845 avail as com as kit item 201 , seeger circlip 20x1part nopoint 05569 , o ring diapoint34 59x2 62 part nopoint 05153 , spring washer b12 part nopoint 05666 , front bearing part nopoint04737 availpointas compointaspointkit item 220 , sealing cap 7 16 unf part nopoint 05545 , set front bearing part nopoint 08179 , metaflex coupling for compressor for 82point5 tr ac plant , catch all filter drier filter drier c 032f , vibration eliminator for suction line , mobil eal arctic 68 , synthetic ref oil savsyn2068 , impeller for sw pump , impeller for cw pump , shaft sleeve for sw pump , shaft sleeve for cw pump , mechanical seal for cw pump , open end spanner set , element filter assypoint , piolpointoperpoint solenoid valve sporlan type 180s with 230v ac coi , solenoid valve evra 15 with 220 v ac coil danfoss , coil for pilot operated solenoid valve sporlan type 180s , compressore discharge pressure gauge , pressure gauge 65 dial 1 to 15 kg cm2 for r134a , temperature gauge 100 dial 0 to 100 deg c , hooter apex 230v ac , mccb siemens 3 pole type 3vl 3720 1dc36 0aa0 200a 55 ka , liquid injection solenoid valves , reverse redpointmarine gear box mg 514 ratio 2 1 forsbmno 504500 , discharge thermostat , hose pump to filter , temperature transducer , cover bearing assly e , oil separator , oil heater 150w , discharge shut off valve , motor side bearing , refrigerant suction filter , capacity contorl piston spring , shim set , oil separator sight glass , shaft seal replacement kit part nopoint kxgs127 , actuator piston seal part nopointxr12059 3 , cylinder screw m8x25 part nopoint 06330 , seal ring 27 8x24 2x2 part nopoint 05791 , tapered comprpointring 80x2 chrpoint part nopoint 06367 , oil scraper ring piston 80 part nopoint 06368 , shaft seal cover gasket part no 06004 , seal plug 1 4 nptf part nopoint 05801 , silicon house 4x1 5 mm 250long part nopoint 01333 , set piston connpointrod wpoint3 rings part nopoint 08491 , set oilspointheatpoint140w 110 130v part nopoint 08430 , gasket set for condensor , cathodic bolt , valve globe type 4 1 8 ods , core for filter driev , filter drier , thermostatic expansion valve , thermostatic injection valve , ss needle valve 1 by 4 ods , thermostatic expansion valve , valve angle type 1 2 ntp m x 1 2 flare , drain purge valve for condenser , safety valve 1 2 npt m set pressure 12point5 kg cm2 r134a , safety valve , charging valve , valve globe type 7 8 ods , valve globe type 1 5 8 ods , check valve in discharge line , core for filter drier sporlan rc4864 , vibration eliminator ss301 1 id double braided screwed en , vibration eliminator ss 304 hose 2 id double braided tota , bearing ball , screw lock cap , shaft forward clutch assembly , shaft reverse assembly , pressure transducer , temperature transducer , solenoid vv alco body 240ra9t 7 8 odf con c nopointpcn 043205 , compressor discharge pressure switch , temperature sensor danfoss mbt 5210 000 0200 0231 , coil for evm evra evrs danfoss 220 vac code 018z6801 , water seawater line differential pressure gauge cum switch , seawater differential pressure gauge , differential prepoint gauge switch hirlekar dpg 200 0 1 kg cm2 , control transformer , smps 24vdc 6point2 amp telemecanique abl1rem24062 , power contactor 230vac siemens 3tf32 00 0am0 , analog input card for plc , analog output card for plc , digital output card for plc , kit for micropressor panel , semiconductor fuse , current transformer mcs ct 250 , fuses for indication lamps 2a siemens , ac ammeter ae rishabh 0 300 900 amps 300 5 ctr 96mm sq , juction boxes and control cabling between controls juction , junction boxes and control cabling , lock washer mb 24 , bush oil , 4 3 way valve , press switch clutch oil , circlip external f 280
Tender For corrigendum : - labour charges for dismanting and pulling of one no. 25 mva, 110/33-22 kv vei make power transformer bearing sl.no.vei/25m/89 at tiruporur 110kv ss in chengalpattu edc towards failure replacement of 25mva power transformer at sriperumbudur 110/33-11kv ss.
Tender For construction of of residential complex with stilt parking i/c water supply, sanitary, electrical installations etc for punjab national bank after demolition of the existing two stories load bearing structure on banks own property at palarivattom, kochi, ernakulam. sh. providing fencing for transformer and cable rearrangement works for obtaining electrical service connection work.
Tender For tender for supply of hose -20mm with threaded end connections , sock mount for main frame , jubilee clip 40mm , nut and bolt 12x100mm ss , level switch , hp flexible hose , victualic coupling , kit shaft seal , prefilter - filter pump shaft seal , filter pump , motor for 30tpd filter / prefilter pump , impeller 30.6id x 73 od x 9h , kit gaskets , cm 3-5 chamber complete p-4d , cm 3-5 pump shaft p-51 , cm 3-5 staybolt m8 p-181 , cm 3-5 kit gaskets , ring-circlips p-931 , casing p-1 , bearing lock out p-22 , bearing lock washer p-69 , cover gasket p-73 , constant level oiler p-77 , bolts p-171d , foot bolt p-171g , coupling , valve kit , seal.oil crankshaft , lockwasher , cap oil filler , gauge oil bubble w-gasket , o-ring crankcase cover , crank case , pin crosshead , seal oil crankcase , slinger barrier , retainer seal 2 pc , spacer lo-pressure seal , adapter male , springs coil , spacer w-coil springs , spacer v-packing , plug for priming , manifold discaharge , protector shaft wh screws , seal kit , o ring over hauling kit , victualing fitting , swash plate set , valve plate set , pulsation damper 0.16 lts. , o ring for head distriutor , sand filter , cartridge filter housing , lip seal dt module , membrane cushion , membrane cushion , pvc-u 2way solenoid vv d20 type160 nc , abs solvent cement , abs ball valve 2 way 25 mm , flow transmitter , o ring union 20 mm , o ring union 32 mm , o ring ball valve 25 mm 3-2 way pvc , connector 1 1-4 bsp m x 1 1-4 vivt , pu 4 hose , coupler for vict. coup.2.5 , pipe clamp 32 mm 2 bolt , elbow pu push in 1-4 mxpu4 qsl-1-4-6 , elbow pu push in fitting 1-4 fxpu4 , straight connector .1-4 m x pu 4 , solenoide valve , sol v-v 1-2 f230v 50hz ss316 2-way-no , two way ball valve with elec. actu. , control cabinet ro 200 , circuit breaker 1.6-2.5amp , pressure switch , miniature relay base for 2 c-o , servo motor control valve , control transformer 160 va , flow meter assembly , impeller grub screw , spacing pipe , spare kit d32 pvc , ball valve 2 way pvc-u 20 mm , dt module clamp , o-ring oil filler cap , edi module tool kit , oil gauge , hp elbow 1.for smcv , end connection flange brine and permeate , rubber hose 20mm , 325 mm long hose , 1650 mm long hose , pulsation damper , cartridge filter housing , cartridge filter element , lip seal dt module-groove ring gasket flange-sealing , air regulator , servo motor control valve , circuit breaker 1.6-2.5amp , miniature relay 24 vdc phoenix 2966171 , fuse base - 20 amp , pressure maintaining vlave , pressure switch , temperature indicator , circuit breakers 16 - 25 a , o-ring , o-ring , thermometer , 2 way ball valve assembly , 2 way ball valve ptfe d32 , ball valve abs 3 way d20 , pulley for motor , taper bush 1610 bore 24 mm , bearing hp pump , plunger rod , oil seal plunger rod , inlet valve adapter , oil drain kit , hp pump inlet manifold , frp filter type 1354 , head distributor , hp crank case oil , s.s. jubilee clips 22 mm to 30 mm , o ring crank case cover , high pressure hose module outlet , control transformer , emi filter mf 423-3-3d 200a , emi-emc choke mf 423-3-2d 200a , pressure transmitter 0-10 bar , level switch , conductivity sensor , conductivity electrode , flowmeter 40-400lph with magnetic float , lp hose 25mm idx1 bspmx500l ss316 , lp hose 32mm , h.p. flex. hose connecting hp pp and pi60 , hp hose of module in , h.p. hose module 1 to module 2 , hp hose sea water distribution manifold of dt module , lp hose hp pump inlet , hp hose discharge hose to dt manifold spool , taper bush 1615 bore 42mm , taper bush 2517 bore 42 mm , v belt , bearing hp pump motor , av mount for hp pp , av mount akcc 85m , mount for permeate transfer pump/filter pump , av mount akcc 40m , av mount for pk20 , hp pump crank case oil , jubilee clips 00 13mm to 20 mm , jubilee clips for d 25 , ss jubilee clips 2x 45 mm to 60 mm , support gravel 0.75 - 1.5 mm , support gravel 3.0 - 5.0 mm , support gravel1.52 - 3.0 mm , sand sup. fine 0.3 - 0.7mm , dolomite , pr
Tender For tender for supply of oem authorised spare part replacement for vrf system at ig hall of residence : : - bearing , eleexpnvalve-efm-25ygmisz-6m-amdv36g , remote controller , room temperature sensor , ductable temperature sensor , cross fan blower , display board vdv-d71/80/90g/n1-s , pipe temperature sensor , stepper motor-hw2.0to2.6tr , synmotorykt-50-4-16 , 1ph , idu pcb for mdv-d71g/niy-c , transformer mdvd45gn1-s , motor capacitor for acdcusc30yg , discharge temperature sensor assembly , pressure sensor , pressure switch , compressor electric heater , exv coil , discharge temp. sensor assembly , dcfanzksp-560-8-2lformdvd450wrn1-b , solenoid vlave assembly , fan ipm , main board assembly of outdoor unit , compressor ipm , filter board assembly , main board assembly of outdoor unit , filter board assembly , outdoor power board assembly , current detection board assembly , outdoor power supply board assembly , compressoripm50a , fan ipm , dcfanzksp-560-8-2lformdvd450wrn1-b , axial fan , solenoid valve assembly , pressure switch , pressure sensor , compressor electric heater , exv coil , dcfanzksp-560-8-2lformdvd450wrn1-b , main board assembly of outdoor unit , contactor , outdoor power supply board assembly , compressoripm50a , outdoor power board assembly , fan ipm , main board assembly of outdoor unit , compressoripm50a , labour charges for one time repairing