Universal Joint Cross Tenders

Get complete information related to latest Universal Joint Cross Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Universal Joint Cross Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Universal Joint Cross Tenders .

Filter

Loading....

Get Tender in Email

CTN :43480889

20 Jan, 2026 NA

Bokaro - Jharkhand

Tender For corrigendum : repair works to be under taken for tyre handler sl no 18085 of bokaro ocp i replacement of drive line front universal joint cross and flange assembly and leaked arm cylinder ii repairing of exhaust silencer engine guard transmission guard iii repairi

CTN :43521989

30 Jan, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For supply of supply of hdpe pipe fittings ms and cs flanges with erection and hydrotesting : : - fabricated unequal tees 250 x 63 mm sdr 11 pn 12.5 pe 100 , ms flanges 2 inch x 150 class ansi 16.5 , concentric reducers 125 x 160 mm sdr 11 pn 12.5 pe 100 , eccentric reducers 150 x 200 mm sdr 11 pn 12.5 pe 100 , 90 degree elbow 200 mm butt fusion is 8360 2022 sdr 11 pn 12.5 pe 100 , 90 degree elbow 63 mm butt fusion is 8360 2022 sdr 11 pn 12.5 pe 100 , 45 degree elbow 160 mm butt fusion is 8360 2022 sdr 11 pn 12.5 pe 100 , ms flanges 10 inch x 150 class ansi 16.5 , ms blind flanges 10 inch x 150 class ansi 16.5 , 250 mm hdpe butt joints , 200 mm hdpe butt joints , 160 mm hdpe butt joints , other size joints less than 6 inch size , erection of hdpe piping , hydrotesting of all loops after jointing , cs flanges 6 inch x 150 class ansi 16.5 , cs flanges 8 inch x 150 class ansi 16.5

State Government

CTN :43551095

22 Jan, 2026 3.00 Lacs

Bundi - Rajasthan

Tender For supply of various sizes of cid joints for hdpe pipes under jurisidictrion of phed div bundi.

State Government

CTN :43555806

20 Jan, 2026 1.50 Lacs

Ajmer - Rajasthan

Tender For supply of 110 mm cid joints for hdpe pipe

State Government

CTN :43555845

20 Jan, 2026 1.50 Lacs

Ajmer - Rajasthan

Tender For supply of 75 and 160 mm cid joints for hdpe pipe

State Government

CTN :43555864

20 Jan, 2026 7.00 Lacs

Udaipur - Rajasthan

Tender For supply of cid joints for hdpe pipe

State Government

CTN :43555866

20 Jan, 2026 1.50 Lacs

Rajsamand - Rajasthan

Tender For supply of cid joints for hdpe pipe 90 mm

State Government

CTN :43555926

22 Jan, 2026 1.50 Lacs

Ajmer - Rajasthan

Tender For supply of 90 mm cid joints for hdpe pipe

CTN :43521542

19 Jan, 2026 NA

Gurdaspur - Punjab

Tender For supply of clutch disc assy , pressure plate , d l kit small , d l kit big , gear lever end kit , trim pad lh , isolator switch , universal joint cross , assy rear view mirror

CTN :43463693

21 Jan, 2026 4.64 Lacs

Thiruvananthapuram - Kerala

Tender For one panchayath one playground- thanniyam stadium in kallara grama panchayath in vamanapuram lac, thiruvananthapuram- supply and installation of outdoor gym and sports equipment - outdoor gym equipments, od252260/2025-2026 : horse rider - supply and installation of horse rider having the following specifications:dimensions: (l x w x h) 1140 x 400 x 1400 mm. main frame - 114 mm od b class gi pipe. foundationplate m.s. round plate of 250 mm & 8 mm thick. foundation cover cap - dome shape of pp / nylon /hdpe material. remaining frame is made by 48 mm od ?b? class gi pipe. seat frame ?is made by 48mm od ?b? class gi pipe. seat position must be horizontal to 110 -120 degree. link - made up of 48 mm od ?b? class g.i. pipe. angle between link and ground position is 10-20 degree. handle - 33 mm od ?b? class gi pipe. paddle vertical support - 60 mm od ?b? class gi pipe. handle frame- 42 mm od ?b? class gi pipe dually bending design. foot pipe - 33 mm od ?b? class gi pipe. support frame ? 10 mm thick ms flat is used. seat- dimension 320 x 270 x 100 mm blow moulded wall thickness 4mm material hdpe.bearing bush closing cap ? pp / nylon / hdpe material. foundation stool: made from main pipe 88 mm od m.s pipe and top support of m.s. round plate of 250 mm & 8 mm thickness is welded at top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft.foundation stool is embedded in c.c. stock below ground level. bearing - use is 6005 permanent lubricated reputed brand.bearing bushes - 60mm od seamless pipe. pin ? made of 25 mm m.s. bright bar. grips - high quality rubber 46 mm od. circlips ? a 24 circlips are used for assembly. coating - best quality of powder coating 60 to 70 micron. safety instructions and exercise chart - start &finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be m20 cc and design shall be approved by the engineer-in -charge before installation.), od252261/2025-2026 : back extension - supply and installation of back extension having the following specifications: dimensions: (l x w x h) 1060 x 730 x 990 mm. main frame - made from 88 mm od ?b?class g.i. pipe. foundation plate ? m.s. round plate of 250 mm & 8 mm thick. leg support - 42 mm od ?b? g.i pipe. seat rest pipe ? 42 mm od ?b? class g.i pipe. handle pipe ? 33 mm od ?b? class g.i pipe.footrest - cast iron 124 x 296 x 5 mm thick and m.s plate of 3 mm thick used to support it. footrest pipe ? 42 mm od ?b? class g.i pipe and 80 x 40 mm ms rectangular pipe. closing cap ?pp / nylon / hdpe material. seat ? 360 x 300 x 2 mm thick m.s. seat with corner fillet for safety. grips - high quality rubber 46 mm od. foundation stool: made from main pipe 88 mm od m.s pipe and top support of m.s. round plate of 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be m20 cc and design shall be approved by the engineer-in -charge before installation.), od252262/2025-2026 : cross trainer (double) - supply and installation of double cross trainer having the following specifications: dimensions: (l x w x h) 2280 x 550 x 1650 mm. main frame- made of 88 mm od ?b? class gi pipe dually bending design. foundation plate ? m.s. round plate of 250 mm & 8 mm thick. paddle vertical support - 42 mm od ?b? class gi pipe. handle - 33 mm od ?b?class gi pipe dually bending design. leg movement frame ? 50 mm x 50 mm x 2 mm thick square pipe. footrest - cast iron 124 x296 x 5 mm thick and m.s. plat

Loading, Please wait...

Universal Joint Cross Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

State Government

State Government

State Government

State Government

State Government