Latest welding torch Tenders | Government welding torch Tenders

State Government

CTN :45621543

29 Jun, 2026 2.73 Lacs

Angamaly - Kerala

Tender For mp-lads-angamaly bp-mp lads 2024-25 honble mp sr. p.p.suneer ( rajyasabha) construction of open gym and installation of equipment at chakkala pongam area of ward -13, thuravoor grama panchayat (infrastructure & purchasc) ernakulam district-general civil work - platform for open gym, 2.32:clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared., 2.8.1:earth work in excavation by mechanical means (hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.all kinds of soil, 4.1.8:providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level:1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources), 4.3.1:centering and shuttering including strutting, propping etc. and removal of form work for:foundations, footings, bases for columns, 4.1.3:providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-iii)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources), od228316/2023-2024:construction of granular sub-base by providing local material, spreading in uniform layers on prepared surface and compacting by ramming to achieve the desired density complete i) using gravel mix/quarry muck, od223449/2023-2024:providing and laying factory made chamfered edge cement concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength,thickness & size/ shape, made by table vibratory method using pu mould, laid in required colour & pattern over 50mm thick compacted bed of stone aggregate, compacting and proper embedding/laying of inter locking paver blocks into the stone aggregate bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of engineer-in-charge.60mm thick cement concrete paver block of m-35 grade with approved colour, design & pattern. modified spec. 16.91.1, od134330/2025-2026:providing and fixing gi pipe hand rail of approved size by welding and all labour charges etc., 5.23:smooth finishing of the exposed surface of rcc work with 6mm thick cement mortar 1:3 ( cement : 3 fine sand)., 13.52.2:finishing with epoxy paint (two or more coats) at all locations prepared and applied as per manufacturers specifications including appropriate priming coat, preparation of surface, etc. complete.on concrete work, 13.52.1:finishing with epoxy paint (two or more coats) at all locations prepared and applied as per manufacturers specifications including appropriate priming coat, preparation of surface, etc. complete.on steel work, od133367/2025-2026:supplying and fixing white stone bench with back rest,2 seater, od139386/2025-2026:providing and laying of interlocking concrete block pavements using80 mm m 40 interlocking paver blocks made by strong vibratory compaction of approvedsize,design @ shape ,laid in required pattern over and including a compacted bed of 6 mm stoneaggregate of 50 mm average thickness etc all complete as per the direction of engineer incharge., od234555/2023-2024:supplying and fixing in place granite name board of slab area less than 0.9sqm includingengraving and painting letters etc complete as per direction of engineer in charge at sitedar spec

Central Government/Public Sector

CTN :45499214

23 Jun, 2026 NA

Haridwar - Uttarakhand

Tender For corrigendum : supply of 1-hw7799992131-contact tip adaptor of mig torch pmt 52w,part no.w004508 oem spare of kemppi, finland , 2-hw7799992026-wire conduit red,l-4.5 meter of mig torch pmt 52w, part no. 4188582 oem spare of ms kemppi, finland dia 0.9-1.2 mm , 3- hw7799992425-contact tip 1.2 dia m8 dhp for stainless steel of mig torch pmt 52w, part no. 9580124ss oem spare of ms kemppi finland , 4- hw7799992409-dl chili teflon liner for al or ss dia. 1.2-1.6, l-3m of mig torch pmt 52w. part no- w005922. oem spare of ms kemppi, finland , 5-hw7799993936- hose clamp of synergic mig or mag welding machine, model- common for msf 57,fastmig and weldforce,part no-9377123 oem spare of ms kemppi, finland , 6-hw7799997320-gun neck for welding torch gx505w, part no-sp012561, oem spare of kemppi, finland , 7-hw7799997346-gas nozzle, for welding torch gx505w,part no-w013931,oem spare of kemppi, finland , 8-hw7799997370-contact tip adaptor, for welding torch gx505w part no- w013203, oem spare of kemppi finland , 9- hw7799997443-wire liner 1,2 al or ss 5, 0 m dl-chili for welding torch gx 505 w part no-w013611, oem spare of kemppi finland , 10-hw7799997451-hose clamp for welding torch gx 505 w part no- sp9377122 oem spare of kemppi finland , 11- hw7799997354-contact tip 1.4 mm m10 std forwelding torch gx505w part no- ct14c2sd001, oem spare of kemppi, finland , 12-hw7799999012-wire liner 1,2 al or ss 5,0 m dl-chili for welding torch gx 505 w part no-w013611, oem spare of kemppi finland , 13-hw7799999020-hose clamp for welding torch gx 505 w part no-sp9377122 oem spare of kemppi finland , 14-hw7799993090-gas nozzle no 4 of water cooled tig torch model no-ttc 250w 4m, part no. 7990766, size-6.5mm, oem spare of kemmpi, finland , 15-hw7799993103-gas nozzle no 5 of water cooled tig torch model no-ttc 250w 4m, part no. -7990770 size-8.0 mm, oem spare of kemppi, finland , 16- hw7799993111-gas nozzle no 6 of water cooled tig torch model no-ttc 250w 4m, part no- 7990771 size- 9.5 mm, oem spare of kemppi, finland , 17- hw7799993073-tighting bush 2.4 of water cooled tig welding torch modelno-ttc 250w 4m, part no. 9876868 oem spare of kemppi finland , 18- hw7799993081-housing for tightening bush of water cooled tig torch model no-ttc 250w 4m, part no.-7990682, oem spare of kemppi, finland , 19- hw7799993120-electrode shield long of watercooled tig welding torch model no.- tx 355 w4m, part no. 7990741, oem spare of kemppi finland

Central Government/Public Sector

CTN :45628480

29 Jun, 2026 1.79 Lacs

Haridwar - Uttarakhand

Tender For hw7799993065 water cooled tig welding torch , o ring of water cooled tig welding torch , hw7799993120 electrode shield long of water cooled tig welding torch , hw8429988394 back cap short l , hw8429960171 water cooled tig torch

CTN :45615600

29 Jun, 2026 NA

Jammu - Jammu And Kashmir

Tender For supply of hex ball point extra long key set , torque screw driver set , tele communication tool set 53 piece , oxygen regulator double gauge , handle arc inverter welding machine , heavy duty wooden table , rotating vice , battery taster li po li lon , spot welding machine , electric screw drive , revit machine , spl tool kit tcm , glue gun stick , vacuum cleaner heavy duty

CTN :45632389

30 Jun, 2026 NA

Jammu - Jammu And Kashmir

Tender For supply of hex ball point extra long key set , torque screw driver set , tele communication tool set 53 piece , oxygen regulator double gauge , handle arc inverter welding machine , heavy duty wooden table , rotating vice , battery taster li po li lon , spot welding machine , electric screw drive , revit machine , spl tool kit tcm , glue gun stick , clamp meter

CTN :45605186

02 Jul, 2026 2.75 Crore

Kondagaon - Chhattisgarh

Tender For supply of furniture and internal fitouts for permanent campus of jnv kondagaon (chhattisgarh) - discription of work, school building, (a) classroom, (i) classroom desk large sizesupply & installation big desk (for two persons)-the overall dimensions of desk will be 1066mm * 930mm * height 760mm, complete as per specifications enclosed and direction of engineer-in- charge having the table top shall be made up of 18.0 mm thick plywood is 303 of mr grade osl (one side shall be laminated, and other side shall have balancer finish). table top dimensions shall be w 900 mm x d 380 mm. edge towards bench shall be post formed with round edge. the remaining three edges must be sealed with 2mmthick pvc edge banding tape. edge band must be trimmed on edges and corners. the desk shall be have low chemical emission of vocs (voltage organic compounds) and carcinogens, contributing to a healthier room environment. seat and back rest shall be made of 18mm thick plywood of mr grade osl (one side shall be laminated, and other side shall have balancer finish) except back rest. back rest shall be have both sides colour lamination.technical details of seat and back rest are mentioned below:seating bench dimensions shall l 930 mm x w 300 mm. front side shall be rounded with post forming. remaining three edges shall sealed with 2mm thick pvc edge banding tape.back rest dimensions shall l 930 x h 200 mm upper side shall be rounded with post forming remaining three edges shall be sealed with 2mm thick pvc edge banding tape. desk shelve shall be made of prime quality 0.8mm thick crca sheet of h150mmxd300mm and side stiffeners of crca tube size 19mmx19mmx1mmthick. one vertical support (partition) of square tube size 25mm square x1.2mm thick must be provided at centre of tray . upper modesty made of prime quality 0.8mm thick crca sheet powder coated should be embossed with dimples in round shape, height will be 150mm, there should be perforated lower modesty made of prime quality 0.8 mm thick crca sheet of size h150mmxd21mm with square perforation, crca tube of size 19x19x1mm thick to be inserted for full length at bottom of jali . bag hook should be provide on both side of piller made of minimum 4mm dia rod side frame structure:- made of prime quality crca pressed form section 165mmx25mmx1mm thick welded to 25mmx50mmx1.2mm thick crca tube , seat and back side frame structure made of prime quality crca pressed form section 165mmx25mmx1mm thick welded to 25.4mm diameter x 1.6mm thick erw-1pipe , there will be 8no. horizontal supports are 25mmx25mmx1.2mm thick crca pipes. .bottom rectangular tube 50x25x 1.2mm thick should be closed with ppcp cap bothside sand pipe dia. 25.4x1.6mm thick should be closed with metal (backside) and other side (undertheseat) ppcp cap, complete as per engineer incharge desk should be in semi knock down form with the help 16 connecting pipes ; 8 pipes on each side : connecting pipe size will be 20x20x1.2mm .all metal pieces shall be welded properly strongly and conformity with regulations with co2 welding shall be used , crca metal shall be coated after being treated with at least three stages and cleaned from oil , grease , dust and other dirt using special thermal control coating for metal furniture to form a layer of base coating of (iron phosphating) (0.4 0.8) gm/m , automatic spray coating shall be applied to be followed by a drying process in a thermal furnace with suitable temperature and time for the process , metal pipe & 7 tank treatment with minimum 45-50 micron powder coating., (ii) classroom desk medium sizesupply & installation medium desk (for two persons)-the overall dimensions of desk will be 900mm w 5 x 890mm d 5 x 688/420mm h 5 , complete as per specifications enclosed and direction of engineer-in- charge having the table top shall be made up of 18.0 mm thick plywood is 303 of mr grade osl (one side shall be laminated, and other side shall have balancer finish). table top dimensions shall be w 870 mm

CTN :45380941

19 Jun, 2026 NA

Dimapur - Nagaland

Tender For bid to ras bid to ras corrigendum : supply of shelter parts constr mtrls elect furniture and toold items for store shelter - shelter parts constr mtrls elect furniture and toold items for store shelter 2654 d d - socket outlet multipurpose 2 in 1 of 6 and 16 amps flush button type isi marked , modular socket outlet multipurpose 2 in 1 16 amps flush button type isi marked , surface mounting modular boxes suit for switches 12 module of size 8 inch into 6 inch , surface mounting modular boxes suit for switches 8 module of size 8 inch into 3 inch , combined cover plate with frame inner and outer of 12 module , combined cover plate with frame inner and outer of 8 module , cealing rose with square box 65 into 50mm 2 to 3 terminals , pvc flexible nibbed pipe 20mm dia , mcb db 06 way spn 240 volt conf to is 13032 , mcb 10 amp sp 240 volt breaking capacity 10 ka conf to iec 60898 , mcb 20 amp sp 240 volt breaking capacity 10 ka conf to iec 60898 , mcb 32 amp sp 240 volt breaking capacity 10 ka conf to iec 60898 , pvc casing caping 38mm wide not less than 2 mm thick , pvc coupler for 38mm casing and caping pipe , pvc tee for 38mm casing caping pipe , pvc sockets for 38mm casing caping pipe , pvc corner bend for 38mm casing and caping pipe , pvc elbow for 38mm casing caping pipe , pvc junction linker 75 into 75mm , house service bracket hook type complete with 3 mtr long gi pipe 40mm dia and ms hooks clamps ans stay , pvc conduct pipe 20mm dia isi marked , pvc coupler for 20mm dia coduict pipe , pvc elbow for 20mm dia conduict pipe , pvc space bar saddles for 20mm dia pvc pipe , insulation tape 19mm width 25mm long , no 8 into 19 csk screw full threaded , no 8 into 32 csk screw full threaded , no 8 into 50 csk screw full threaded , no 8 into 75 bolt and nuts full threaded , store rack as per specification given in appx c of ts , chair writing as per specification given in appx d of ts , writing table as per specification given in appx d of ts , almitrah steel large as per specification given in appx d of ts , hand held trolley as per specification given in appx d of ts , hand held fire extinguisher as per specification given in appx d of ts , smoke alarm as per specification given in appx d of ts , heat alarm as per specification given in appx d of ts , habd held grinder cutter 125 l professional rated input power 1800 w 11500 rpm 125mm disc dia make as per appx ii of ts , bosch grinder cutter blade 125mm dia make as per appx ii of ts , portable welding machine arc 220a built in hot start anti stick and adjustable arc force heavt duty make as per appx ii of ts , plaster 6 inches material wooden heavy duty wooden hand float trowel 10 inch into 6 inch polished wood plastering , plaster 8 inches material wooden heavy duty wooden hand float trowel 10 inch into 6 inch polished wood plastering , hand gloves masonery work flocked liner neoprene over latex coating safety gloves , spirit level 3 feet , spanner set no of spanner 8 size 6mm to 22mm generally conf to is 2028 to 2008 make as per appx ii of ts , plumbob with kanda and 2 mtr thread make as per appx ii of ts , iron tasala 10 kg capacity , iron bucket 15 ltr capacity , nylon rope , sintex 500 ltr thrree layer pvc water tank 500 ltr capacity make as per appx ii of ts , brick hammer weight 5 kg make as per appx ii of ts , ball pane hammer weight 1 point 35 kg make as per appx ii of ts , ms electrical tool kit make as per appx ii of ts , welding rod 60 pcs size 4mm into 450mm in one pkt , double wheel concrete trolley fabricated heavy duty ms sheet and ms frame with 80 to 100 ltr cap constr mtrls with loading cap upto 300 kg make as per appx ii of ts , drilling machine adopter make as per appx ii of ts , screw driver set make as per appx ii of ts , cutting plier make as per appx ii of ts , wire cutter make as per appx ii of ts , tester make as per appx ii of ts , revit //bid details 2 / 58 machine make as per appx ii of ts , revit 500 nos in one pkt , concrete mixer machine 230 ltr with 1 h

Central Government/Public Sector

CTN :45597465

09 Jul, 2026 NA

Amritsar - Punjab

Tender For comprehensive annual maintenance contract of 102 nos kemppi mig welding plants and 147 nos of mig welding torches including consumables for 2 (two) years with oem/ authorised dealer.