Tender For supply of armature , field coil , pinion , brush carrier , bush set , solenoid switch , sr 60 , regulator alternator , relay starting 24v , head lamp relay , head lamp bulb , fog lamp bulb 24v 70w , tail lamp bulb , assy magnetic valve 24v , real wheel bearing 32213 , axial roller bearing , fan belt , clutch master cyl , clutch cyl r kit , slave cyl new model , gear lever rep kit , rear hub seal , front hub seal , gear box oil seal , transfer case oil seal , frnt and rear axle seal , spidle bearing inner lock and outer lock , knuckle post , accelerator cable rotery , speedo cable 4300 mm
Tender For supply of places , replacing wornout runner base and installing a new runner base of cane carrier and baggage elevator and r b c , replacing wornout runner with new one of cane carrier and baggage elevator and r b c , removing wornout angle iron and t iron of the cane carrier and reinstalling it by straightening the crooked part , removing the wornout part of the suit from different places and fitting it with new one , chevron grooving of new rollers of the mill , chevron grooving of old rollers of the mill , remove the wornout partition plates of the juice box above and below the juice heater by 10 or 12 mm ms plate and install it , installing ribs at the top and bottom partitions of the juice heater , repairing save all of qurdbody , removing old wornout gutters installed at various places and installing it with new gutters , remove the old wornout save all from pan and quard and install it with new one , reinstalling the new umbrella fitted inside the pan by making a new one and removing the old one , replacement ribbon arm of the mascute receiving crystallizer , making new separator of a centrifugal machine , removing the wornout truff of the hopper and installing it with new one , making and installing new separators for continuous centrifugal machines , removing the tubes of quad juice heater and dynamic juice heater and expanding them by installing new tubes and giving their hydraulic testing satisfactory of size 42 mm , removing the tubes of pan installing new tubes and expanding them and giving hydraulic tesing with satisfactory trial of size 96 mm , removing the wornout flue gas ducting of both the boilers and installing it with newone making from new or old plates , removing the wornout front and roof plate at boiler number 1 and 2 and installing with a new plate , removing the damaged boiler damper and installing a new one , making bagasse suit and installing. , replacement of juice over flow box of clarifier , making and installing bed of motor and pumps at various places as per requirement , replacement 6 inch dia cooling pipe of sulfur furnace , removing the monitor casing of a machine from old machine and installing it and giving its a trial , making amd replacing manholes at various places , making and replacing the enternals of cather of the pan. , making and replacing the new hood of cane cutter , removing the old bottom plate of the lowest compartment of the clarifier and placing a new plate on it after placing an angle trap as per the instructions and giving a satisfactory water trial , reinstalling the stirrer of the clarifier and giving a satisfactory trial , removing the shaft of a pug mill and replacing the old bushes on both sides and fitting new ones , removing and refitting the shaft of a brown sugar magma mixer and installing with new bush , reinstalling the trufff of connecting rod of the hopper , making and installing new catcher strainer , removing the old rail line of the trolley of the unloader and fitting the new rail line satisfactorily and doing water level , reinstalling the old rail line of the unloader s bridge and fitting it and checking water level etc , removal of old and weak channels of 3 inches to 10 inches diameter installed at various places and installation of new ones as per requirement , cutting and straightening old plates installed at various places as per requirement , removal of old and wornout scrubber installed on sulfur furnace and making and replacing with 8 or 10 mm plate and making all the connections , removing the trufff plate including support corroded shell and top cover plate of the top chamber of the clarifier and fitting the new plate and giving it s a water proof trial , re-installation alignment and //bid details 2 / 47 trial of hopper driving end , making and installing the top cover of the centrifugal machine , making an arm and installing it on the shaft of pug mill , making and installing scrubber and bottle jackets of sulfur furnace , making and install
Tender For repairing of battery box, support of carrier roller, grease plate, operator cabin gates, its mountings, fan pulley, both side 54nos. sprocket holes, tilt cylinder steel pipe and its guard, trunnion back guards, both side track frame of d355 dozer d19
Tender For supply of iron safe 03 locker make-godrej or similar configuration safe deposit box / cabinet - for safe keeping of paper / cash / documents type an individually secured container for paper / cash / documents constructions double cabinet type ? cabinet inside cabinet comprising of an external cabinet and internal cabinet for body as well as door number of drawers n.a assembly of components by combination of bolting , welding and riveting or screwing elding by annual rate contract welding conforming to is 816/latest number of shelves 2 main locking arrangement no secondary locking no snap shut mechanism on door no annular sealing gasket between inner body and door n.a fire seal no key retention mechanism in drawers n.a sensor to detect attack on safe using tools (power hammer, power drill or similar) na alarm transmission from inside of safe (safe is in locked condition) n.a alarm transmission n.a minimum battery life n.a time bound health monitoring n.a encrypted communication between safe and alarm panel (at least aes-128 bit) n.a distance of alarm panel from safe n.a method to arm / disarm n.a alarm panel alerts for burglary attempt no alarm panel alerts for panel tempering no wireless sensor communication usinge unlicensed band carrier frequencies n.a number of telephone numbers that can be programmed to receive alarm alerts in the form ofvoice and / or sms n.a anti fishing mechanism for coin slot no snap shut mechanism for drawer no bolt detent mechanism for main door no material for internal cabinet steel material for external cabinet steel door material steel shelves material steel handle material zinc base alloy type of main lock 6 lever dual control type of secondary lock no secondary lock number of locks no lock depository drawer lock n.a inside height of safe 10mm 560 mm inside width of safe 10mm 362 mm m inside depth of safe 10mm 355 mm external height of safe 10mm 764 mm external width of safe 10mm 505 mm external depth of safe 10mm 540 mm inside height of top drawer n.a packing corrugated sheet packing marking n.a marking of key n.a surface finishing n.a warranty periods 1-year [ warranty period: 30 months after the date of delivery ]