Latest aerial branch cable Tenders | Government aerial branch cable Tenders

CTN :45415548

18 Jun, 2026 NA

Coimbatore - Tamil Nadu

Tender For purchase of chemicals - purchase of chemicals, co sensor:0 5000 ppm range, (50 ppm + 3%) accuracy, uart/i c interface, 3.6 5.5 v dc, 10 c to +60 c, combo sensor (temp, humidity, barometric pressure, vocs):digital i c/spi interface, operating range 40 c to +85 c, supply voltage 1.7 3.6 v, rain detection module:analog/digital output, 3.3 5v dc, corrosion-resistant pad, light intensity sensor:400 700 nm range, i c/analog output, measures ambient light in lux, wind speed and direction integrated sensor:360 direction, 0 60 m/s speed range, analog/digital output and suitable for outdoor climatic monitoring, 220v ac power cable, smps (ac to dc power supply, 5v & 12v output):ac to dc power supply, 5v & 12v output, smps (ac to dc power supply, 24v output):ac to dc power supply, 24v output, esp32-wroom-s2 module: wi-fi-enabled mcu, 32-bit lx7 core, 4mb flash, uart/spi/i c interfaces, operating voltage 3.0 3.6 v, led indicators:3mm/5mm, red/green/blue, 2v 3.3v forward voltage, for status indication, lcd display:16x2 characters, hd44780 compatible, i c interface, 5v dc, i/o connectors (2-pin, 3-pin, 4-pin, rmc):2/3/4-pin, rmc type, pitch 2.54 mm, for sensor and power interfacing, real time clock (rtc) module:i c interface, battery backup, accurate timekeeping for data logging, gsm gprs module sms chip:quad-band 850/900/1800/1900 mhz, supports uart interface, sim card slot, 3.4 4.4 v dc input, wires (jumper, power, signal wires combined)rainbow wires - 10 core, red and black wires - 10 core and 5 core, 1.5 sq mm electrical wires, 2 sq mm electrical wires, soldering paste:no-clean flux, sn63/pb37 alloy, for smt component soldering, soldering lead:60/40 alloy with flux core, 0.5 1 mm diameter, universal pcb prototype board double-sided:double-sided fr4, 2.54 mm pitch, tinned pads for soldering, xt60 connectors:high-current (up to 60a) dc connectors, enclosure box (for electronics):weatherproof (ip65/ip66), uv-resistant abs/polycarbonate, wall/pole mountable, suitable for outdoor sensor and control units, zip ties:nylon, self-locking, 100 300 mm length, cooling fan (5v):5v dc, 40mm, brushless, sleeve bearing., switches:(5 amps, 10 amps, 20 amps), lead acid battery (12v):rechargeable, sealed maintenance-free, capacity 7ah 26ah, sunlight ultraviolet ray intensity (uv) sensor:detects uv radiation in 280 400 nm range, outputs uv index (0 11+), analog/digital interface, suitable for outdoor uv monitoring, lead acid charger:12v output, automatic overcharge protection, input 100 240v ac

CTN :45386611

15 Jun, 2026 NA

Tuticorin - Tamil Nadu

Tender For purchase of lab equipments for basic eng dept - purchase of lab equipments for baisc eng dept (physics and chemistry), digital balance itemcode: a001 weight 500g, accuracy 0.01g, top pan. tare function, caliberation- automatic external display type: led., joule s calorimeter itemcode: a005specifications:copper vessel, battery eliminator 3a, (2,4,6,8,10,12 v), tubular rheostat 20-3.3a, one way plug key, analog type dc ammeter (0 2a), voltmeter (0-5v), thermometer (alcohol), stop clock, ic regulated battery eliminator itemcode: a011specifications:ic regulated, input: 230v ac; output: 0-12v dc in steps of 2v; capacity: 1a or 2a., galvanometer itemcode: a012specifications:moving coil type, 30-0-30 scale, unbranded with bhel specification-sensitivitysensitivity, voltmeter itemcode: a013specifications:dc voltmeter; range 0 10 v, analog., ammeter itemcode: a014specifications:dc (0 - 2 amp), decade resistance box itemcode: a016specifications:resistance box 12 month warranty (dial type) -manganin coil- 2 dials, sonometer apparatus itemcode: a017specifications:sonometer with meter scale attached along with knife edge, tuning forks set 256, 384, 512 ranges, hammer, slotted weight - 500 gm each to a total of 3 kg. brass wire (5 m), travelling microscope itemcode: a018specifications:branded travelling microscope 0 200 mm horizontal and 0-150 mm vertical measurement, potentiometeritemcode: a019specifications:it features a 1-meter to 10-meter constantan/manganin wire stretched on a wooden or sunmica baseboard with a millimeter scale. it includes 4mm brass terminals, a pencil jockey for contact, wire options (10 wires), and a typical resistance range of 10-20 ohms, ideal for high-precision voltage measurements., rheostat itemcode: a021specifications:high-grade ceramic tube, oxidized resistance wire, 0.5a 5a, range 10 100 ., deflection magnetometer apparatusitemcode: a022specifications:deflection magnetometer apparatus with compass box and two short bar magnets, digital electronic balance /analytical balanceitemcode: a001/a007specifictions:load capacity: minimum,500 g readability: 0.01 g,linearity: 0.02g,display: lcd/led,tare function: required,top pan typepower supply: 220 240 v,ac, 50 hz, digital tds meter itemcode: a002specifictions:measuring range: 0 9990,ppm resolution: 1 ppm,display: lcdautomatic temperaturecompensation (atc): requiredwaterproof: minimum ip67 protectionpower source: battery, operated (button cell/aaa, digital ph meter benchtop model itemcode: a003specifications:ph type microprocessor/microcontrolle r ph range: 0 14resolution: 0.01 ph,accuracy: 0.05 ph or better combined ph electrode with temperature sensor two or three-point calibrationfacility temperature compensation type automatic display: lcdpower supply: 220 240 v ac, 50 hz warranty minimum 1 year, laboratory heating mantle (knitted glass yarn) itemcode: a004specifications:capacity: 500ml,temperature range: ambient to 350 c energy regulator/control knob:required power supply: 220-240 v ac,50 hz, mortar with pestle itemcode: a006specifications:material: porcelain size: 100 150 mm inner diameter exterior: glazed grinding surface: unglazed, hot plate itemcode: a008specifcations:top plate material: cast iron plate size: minimum 8 inchdiameter power rating: 2000 w temperature range: ambient o 200 c minimum thermostatic temperaturecontrol: required power supply: 220 240 v ac, 50hz., electric bunsen burner itemcode: a009specifications:electrically operated energy regulator/ control knoboperating temperature 800 c body: stainless steel power supply source: corded electric, supplied with a heavy-duty, heat-resistant,earth-grounded, 3-pin power cord (minimum length 1.2 meters). power consumption: between 350 and 500w power supply: 220 -240 v ac, 50 hz, water distillation unit itemcode: a010specifications:output capacity: 4 litres per hour (lph) ph value: 5.5 to 7.0conductivity (raw water distillation):3.0 4.0 s/cm or less glassware material:borosilicate 3.3 glass (pyrex/duran

Central Government And Public Sector

CTN :45400982

09 Jun, 2026 NA

Multi City - Punjab

Tender For auction sale of depot miscellaneous scrap - scrap of old condemned electical fitting consisting various types of tubes, compressor, heaters, meters circuit, switchess, stabilizers pannels, capacitors, flood lights, tube rod, exhaust fans, antenna assly, various types of motors wires, meter boards,various electrical parts and machine, electrical parts of micropreocessor based control, electrical equipments, scrap parts and components of sort and sizes. to pl no.-98414501

Central Government/Public Sector

CTN :45343151

03 Jun, 2026 NA

Multi City - Karnataka

Tender For auction sale of depot miscellaneous scrap - ubl/gsd/b-0022/ electrical/26/b[pl no.98411019] condemned and un-serviceable electrical scrap consisting of reading light fittings, emergency light and fitting, cfl/fl fittings, air fittings, fl box type fittings, tail lamp fittings, sockets, socket control panel boards, tpic/dpic switch boxes, ballast, capacitors, avm, iron box, wooden switch board, suction apparatus with accessories, stabilizers, plb switches, tube light fittings, electrical parts covers, head light resistors, carbon brushes, holder and parts, revdel, head light dim resistor, different types of measuring/checking devices/instruments, tx rx coil, with cables, connection box, fuces, ignitors, hotoor for lc gate, head light switches, cab fans, grass/tree cutter, different types of lights and its fittings, connecting wires, ovpr,dsp, junction boxes, dfb, different types of switches, electrical equipment covers, smps parts, classification cover knife switch covers, plungers, 2*2lsed panel light fittings, terminals board assembly , rotary switches,& other parts, light mast fittings 400w , coolers, grinder, relay jack,timer relay,siemens relay and other realeated parts, street light, limit switches, mcb, pressure switches over voltage relay, wiper blades, ultrasonic flaw detector, gasoline run concrete machine, guard control switches, contactors, bracket holder junction boxes with wire attached, electronics spare parts, pcb board, transformer parts, motor releted parts led driver,door closer armature, alternators and starter parts ,street lights ,defferent types camera and spare parts radiator conteceetor or wing assembly head light , bulb fixing, cab fan, frames & buses and clamp, ivr, fuse alarm unit,solar panel coupler socket, other parts.wiper parts mh choke/copper blast ,ovpr 25k/4.5,and other electrical/electronical parts with or without ms/steel/aluminum/cables attached scrap. available under the custody of cdms/rs ward/gsd/ubl. note: bidder has to physically inspect the lot before bidding. location:- road no 02 block b bin no-022 gsd/ubl. remarks-. delivery should start from one end. no pick and choose allowed

CTN :45322644

01 Jun, 2026 8.70 Lacs

Sawai Madhopur - Rajasthan

Tender For supply, installation, testing and commissioning of phase wire and street light and vairious electrical equipment needed for implementation of budget announcement 2025-26 - providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket/pole. fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing with uv stabilized pc (uv stablization report submitted for uv cover ) /toughened glass cover and secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm/ wt and potted driver & has a unique bis r number with input voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driver efficiency >85% ,thd(i) 70 and cct 5700k +355k. surge protection shall be min 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs. manufactures word mark/name engraved/embossing on die cast housing to allow traceability/authenticity. fixture shall be as per is 10322 complianced.oem must have its own in, led street light fixture with minimum lumen output 5600 lm, sitc of ip-42 and general construction confirming to is:8623 : 1993, wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as specifications and other parameters required as per point (a) ,(b), (c),(d), (e), (f), (g), (h) as below:-(a)thickness of crca sheet shall be 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / without detachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided(b)complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel. the panel having pe foam/ neoprene rubber gasket of not less than 3mm thickness ,required hardware , concealed hinged door with key type locking arrangement for equipment/switchgear earthed with 2.5 sq.mm braided copper wire.[c) interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 63 amp ) and by solid bus bar (>63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only. all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgear is to be paid extra )(d)wiring between components within switchgear and incoming / outgoing cable shall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap-offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram.(e)all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be point to point (no wire splitting or tee connections) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging.(f)floor mounted panel sh

Central Government / Public Sector

CTN :45010670

03 Jun, 2026 NA

Vijayawada - Andhra Pradesh

Tender For supply, erection & installation of 't' shaped modular workstation having two keyboard pullout trays, two cpu trolleys, two storage encase metal pedestals, two ergo footrest and also provided with integrated cable management as per specification details mentioned below. 1) two workstations, each shall be of 5 feet( l) x 5 feet (w) x 4 feet(h) and the total combined 't' shaped modular workstation size: 10 feet(l) x 5 feet(w) x 4 feet(h) = 01 set(which is made up of 25 mm hpl/nfc engineered wood & 1 mm acrylic laminate). 2) all the interconnecting wiring for lan, power supply and telephone wires shall be done inside the cable management system(powder coated aluminium interlocking extrusions) and adequate ports shall be provided on the work surface. 3) standard communication & power accessories :- i) lan rj45 ports : 4 nos ii) telephone rj11 ports : 4 nos iii) power supplies 5 amp. sockets : 6 nos 4) all wires shall be brought out to interface boxes as one for power supply and another for the communication cables. these boxes shall bedesigned to accept connections from the control room circuits. 5) modular workstation material shall confirms to hpl/nfc engineered wood(25mm thickness) or its similar as per epd-ies-0012055 : 002 (s-p-12055) certification or latest if any. note:(1)firm shall quote any one make for the tendered description along with valid authorization, if vendor offers/bids for more than one make or if the firm mentions, 'as per tender' in their bid(s), their offer will be summarily rejected. (2) tenderer must submit technical leaflets/ details of the offered material like make & model no. along with their offer, otherwise such offers are liable for rejection. [ warranty period: 30 months after the date of delivery ]

State Government

CTN :45289480

30 May, 2026 NA

Palamau - Jharkhand

Tender For renovation of electro mechanical items for rural ws scheme, lesliganj - part a (raw water p/plant mali river at sitadih ), cost towards repairing and overhauling of 50 h.p. v.t. pump set multiple stage ball assembly s/f impeller g.m. bush as per sample 5 nos each, s/f housing bush as per sample. replace in spider rubber cutless bush 5 nos, replacing of 25mm dia. 5 feet long s.s. line shaft 4 nos with s.s. socket . transportation charge from site to work shop vice versa including tools tackles and labour charges for lifting & lowering v.t. pump before and after repairing work etc all complete at pumping plant., supplying all labour tools and tackles for complete opening, dismantling , cleaning of its slots of stator by brush & petrol then complete rewinding of 50 h.p. 440 volts, 50 c/s, star delta, 3 phase hollow shaft v.t. motor by supplying super enameled copper wire & binding, tapping varnishing, heating, testing on full load and repairing of stator & rotor, changing of bearings as per sample skf make with including the deduction of cost of burnt copper wires and transportation charges from p/plant to workshop and back to the same . including tools & tackles and labour charges etc all complete at p/plant., cost towards repairing/ replacement of 200 amp motor control panel board consisting of incoming feeder mccb 200 amp 1 no. and outgoing feeder mccb 100 amp 2 nos, timer 1 no., thermal over load release relay 2 nos. supplying and fitting of digital volt meter (0-500v) squared type 2 nos, ammeter (0-125amp) squared type 2 nos and replacement of phase indicator lamp 3 nos. including internal wiring etc all complete., cost towards supplying & fitting 35 mm2 3 core copper conductor 15 mtr panel to motor., cost towards supplying & fitting 60 watt led street light (jsor-m840), part b (clear water lesliganj.), cost towards repairing/ replacement of 200 amp motor control panel board consisting of incoming feeder mccb 200 amp 1 no. and outgoing feeder mccb 100 amp 3 nos, timer 1 no., thermal over load release relay 3 nos. supplying and fitting of digital volt meter (0-500v) squared type 2 nos, ammeter (0-125amp) squared type 2 nos and replacement of phase indicator lamp 3 nos. including internal wiring etc all complete., supplying all labour tools and tackles for complete opening, dismantling , cleaning of its slots of stator by brush & petrol then complete rewinding of 20 h.p. 440 volts, 50 c/s, star delta, 3 phase induction motor by supplying super enameled copper wire & then tapping varnishing, heating & testing on full load and repairing of stator & rotor, changing of bearings as per sample skf make with including the deduction of cost of burnt copper wires and transportation charges from p/plant to workshop and back to the same . including tools & tackles and labour charges etc all complete at p/plant., cost for repairing of 20 h.p. c/f pump with m/s/f s.s. shaft as per sample 1 no. c.i. gland tightner 2 nos, c.i. bearing housing 2 nos, ms. check nut 2 nos, c.i. neckring 2 nos, ball bearing s.k.f. as per sample 2 nos, all labour tools & tackles and materials with loading and unloading transporting charge from site to workshop & vice versa., cost towards varnishing, heating of winding & greasing of both side ball bearing of 25 h.p. induction motor 3 phase, 1440 rpm, volt 410 10% 50 cycle along with supplying & fitting of tyre coupling 2 nos, then testing on full load at site including supply of all labour tools and tackles., cost for repairing of 25 h.p. c/f pump with m/s/f s.s. shaft as per sample 1 no. c.i. gland tightner 2 nos, c.i. bearing housing 2 nos, ms. check nut 2 nos, c.i. neckring 2 nos, ball bearing s.k.f. as per sample 2 nos, all labour tools & tackles and materials with loading and unloading transporting charge from site to workshop & vice versa., supplying all labour tools and tackles for complete opening, dismantling , cleaning of its slots o

CTN :44042113

25 May, 2026 NA

Ernakulam - Kerala

Tender For bid to ras tender for supply of hose-hydraulic , spacer , screw , screw , screw , nut , nut , washer , washer , washer , thrust washer , washer , stud , stud , element-fuel filt , o-ring , clamp , o-ring , driver tool , oil seal , installation tool , sleeve , seal , harness assy , harness , actuator , thermostat , valve-cdr , high performance gear lube , bearing assembly , cable kit , lever-steering , bellows assy , universal joint , repair kit , filter , fuel , sensor , sensor , mount - engine , gasket , pump assembly - injection , anode assy , air cooler , screw , gasket , anode kit , washer , liner-cylinder , air cleaner , filter element , hose , washer , starter 12v , pipe , sensor , belt , key switch kit , voltage gauge-black , fuel gauge , console mount remote control , cable t/s g2 20ft , thermostat valve , switch kit , start/stop - single , o-ring , seal , harness assy , nut , cylinder head , corrosion guard , mercury diesel engine oil , extended life coolant , ring , retaining , ring , retaining , shaft upper , manifold assy , seal , o ring 2 , battery lugs , switch for navigation light , o ring 5 , fuel filter 2 , seal-swivel tube , o ring 2 , o-ring , hose , thermostat , assy-lower mount , ring-retaining , seal kit , fsm , ngk zfr5f 4 , gasket , hose fsm to rail , cable t/s g2 12ft , spark plug wires , gearcase seal kit , o-ring kit , trim , gasket cyl head , ring set , piston , screen fuel fltr , thermostat assy , gasket exh man , bearing-con rod , repair kit-w/p , repair kit - imp , seal-top m brng , pin-cotter , screw , plug shift shaft oil seal , plug kit- drain , connector , nyliner , bushing , bushing , spacer , o ring , o ring , o-ring , o ring , oring , o ring , o-ring , seal , oil seal , seal , gasket , gasket , bearing needle , hose 54 inch , tube exhaust , hose exhaust , hose-hydraulic , hose- breather , hose , hose-trim cylinder(starboard) , hose-trim cylinder(port) , hose-hydraulic-trim cylinder to connector , diesel filters , bell housing assy , seal , seal , hsg assy-gimbal , impeller , ring-retaining , ring-retaining , clamp , belt , bearing ball , str rotary kt 12 , steering cable , battery lugs , bilge pump 500 , std cable tie , bellows , stud , (m8 x 90) , element filter , o-ring , coupling hub , anode kit 2 , monitor assy-lube

Central Government / Public Sector

CTN :45255485

09 Jun, 2026 NA

Secunderabad - Telangana

Tender For supply, installation and commissioning of pre-wired modular workstation consisting of a single control office customized to equip two sads and two daws systems arranged and installed on a t-shaped modular workstation with integrated cable management systems as per specifications. specifications of modular workstation: 1) the workstation shall each be of 5 feet (l) x5 feet (w) the combined size: 10 feet (l) x 5 feet (w) - 1set, made of 25 mm nfc wood and 1 mm acrylic laminate. 2) the sads displays shall be installed such that the bottom edge of the display is at a height of 5' (approximate) from the floor. these shall be installed preferably along the longer edge of the t and facing the operators, 3) the daws system shall be installed such that it is possible to be used sitting at the workstation. 4) all interconnecting wiring for lan, power supply and telephones shall be done inside the cable management system (powder coated aluminium interlocking extrusions) and adequate ports shall be provided on the work surface. communication accessories: i) lan rj45: 4 nos ii)telephone, rj11 : 4 nos iii) power supply, 5 amp sockets: 6 nos 5) all wires shall be brought out to interface boxes one for power supply and another for the communications cables. these boxes shall be designed to accept connections from the control room circuits. note: design, supply, fitment, installation, testing and commissioning shall have to done by the firm confirming to the pre-wired modular t- shaped workstation standards. material shall confirm to hpl/nfc engineered wood (25mm thickness) as per epd-ies-0012055:002 (s-p- 12055) certification. make: godrej interio/tumbi/greeken/moudulartek or its equivalent. [ warranty period: 30 months after the date of delivery ] ]

Central Government And Public Sector

CTN :45114128

26 May, 2026 2.65 Lacs

Ahmedabad - Gujarat

Tender For corrigendum : supply of replacement of compressor for extg 1.5 tr split ac , replacement of indoor unit motor for extg split ac , replacement of outdoor unit motor for extg split ac , replacement of pcb control unit for extg split ac , carrying out aand attending leak test and gas charging for extg split ac units , supply and fixing 0.5 inch cu refrigerent pipe with insulation and wires , supply and fixing 0.25 inch cu refrigerent pipe with insulation and wires

Aerial Branch Cable Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government And Public Sector

Central Government/Public Sector

Central Government / Public Sector

State Government

Central Government / Public Sector

Central Government And Public Sector