Latest air receiver spares Tenders | Government air receiver spares Tenders

CTN :45679372

02 Jul, 2026 20.16 Lacs

Delhi - Delhi

Tender For supply and replacement of defective parts of kirloskar make transformers of 1000/750/500 kva capacity at ugc & cag building, new delhi. - supply and fixing of over current earth fourth relay 24 dc l&t make etc complete as reqd. , supply and fixing of 11 kv indoor single phase resin cast current transformer 300/5amp etc complete as reqd., , supply and fixing of transformer 500 kva 11/0.433 kv wt1 scanner & rtd sencer lead., , supply & installation of suitable rating of 500 kva 11/0.433 kv lv bussing porcelain or epoxy-cast resin comply with is-1180 complete as required, , supply and fixing of suitable rating of 500 kva 11/0.433 kv lv flexible porcelain or epoxy-cast resin comply with is-1180 complete as required., , dismantling /loading and unloading of 500kva, 11kv/433volt, 3phase, 50hz, cast resin dry type kirloskar make indoor transformer hv/lv coil/core etc and repair of crack in hv/lv winding/core and putting cast resin/resin hardener, reassembling all the dismantle parts accessories confirming to is 11171 and iec 60076 etc including all tests i.e voltage ratio, magnetic balancing, vector group, ir magnetizing current, winding resistance etc complete as reqd., , supply & installation of 630a vcb vacuum interrupter etc complete as reqd., , sh-2 (old cag bldg), , supply and replacement of 750- 1000 kva transformer oil gas kit etc complete as reqd., , checking in 750-1000 kva transformer all type of protection etc complete as reqd., , supply and replacement of lv bushing oil seal in 750-1000 transformer etc complete as reqd. no.ryb) (4, , supply and replacement of hv bushing oil seal in 750-1000 transformer etc complete as reqd. (3 no. r,y, b), , supply and replacement of off load tape changer in 750-1000 kva transformer etc complete as reqd., , replacement of transformer oil in oltc top-up of main tank etc complete as reqd., transformer oil filtration and dehydration of 750 kva & 1000 kva transformer using high-vacuum oil filtration plant, including removal of moisture, dissolved gases, sludge and impurities from transformer oil, circulation of oil through filtration machine, achieving required bdv value, testing before and after filtration, manpower, tools & tackles, consumables, complete as required at site., , complete servicing, overhauling, cleaning, contact checking, lubrication, insulation resistance testing, contact resistance testing, functional testing and commissioning of oil circuit breaker (ocb), complete as required at site., , supply & installation of male contact, , supply & installation of female contact, , supply & installation of over current earth fault relay, , supply & installation of 24 volt dc power pack unit etc complete as reqd., , supply and fixing of transformer wti relay etc complete as reqd.., , supply and replacement of transformer oti relay etc complete as reqd.., , providing and fixing following rating and breaking capacity and pole mccb with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, ics=100% icu and operational voltage 690v etc. as required., , (make: schneider electric-nsx /siemens / lk/ abb/hager)

Corporations And Associations And Others

CTN :45651274

29 Jun, 2026 1.99 Lacs

Delhi - Delhi

Tender For procurement t and p items for ward no. 151 (munirka) south zone - supply of telescopic pole pruner:-specification:-pole length including blade: 6.5mblade material: hardened & tempered high carbon steel. the head of the blade shall have a hooked tip useful for cutting twigs saw blade shape: hooked type curved sawblade type & no of cutting teeth: tripple grounded 86 teeth blade length: 15"-16" pole type: light weight telescopic tubular aluminum alloy extendable pole no of positions for pole height adjustment: 10 positions locking mechanism: ergonomicvally designed two way locking mechanismtotal working length: max 219"(6623 mm), mln 103" (3103mm) branch cuttingcapacity: 200mm max, petrol operated brush cutterengine: single cylinder, 2 stroke, aircooled onlyengine displacement: 40.2ccpower output: 2kw/2.7hpmax output shaft speed at cuttingattachment: should be minimum 9000 rpmcarburetor: diaphragm with compensator technology.fuel tank capacity: minimum 600 ml.weight(dry, without cutting attachment & deflector): should not be more than 7.5 kg clutch: centrifugal type, clutch shoe support base & lining metal only. multi function handle: should have acceleration, on/off switch at right handle. brushcutter harness: should be double shoulder harness only. anti vibration system: must have 4- point aniti vibration system. vibration level in m/s2 at right handle: should not be more than 2.5 m/s2 sound pressure level db(a): should not be more than 105 db(a) drive shaft design: must have drive shaft ends square design type only.certification: must have valid en certification, telescopic petrol operatedpole prunerengine: single cylinder, 2 stroke, air cooled onlydisplacement: should be between 25-30 ccpower output: should be minimum 1.2 hpweight (dry without cutting attachment & fuel): should not be more than 7.5 kgfuel tank capacity (ml): should be minimum 400mlchain oil capacity (ml): must have minimum 200 ml.clutch: clutch shoe linining should be metal only.guide bar length: minimum 30cmguide bar and chain: should have same manufacture onlychain type: every drive link need groove & small oil holes for better lubrication. saw chain pitch should be 1/4" or 3/8picco only and drive link thickness must have 1.1 mm or 1,3 mm.max. output shaft speed (rpm): should be minimum 8000 rpm at chain sprocket.equipment total length with guide bar and chain (cm): should be minimum 220 cm - compressed & total length of equipment -minimum 350 cm - extended.sound pressure level (db/a): should not be more than 95 db(a)vibration measurement m/s2 at control handle extended position: should not be more than 5.5 m/s2certification: must have tuv certification with test standard en iso 11680, petrol operated chain sawengine : single cylinder, 2stroke, aircooled onlydisplacement: 45.4cc poweroutput: 2.3kw. 3.0 hpmax. engine speed (with guide bar & chain): at least 12500 rpmcarburetor: diaphragm type compensator technology.fuel tank capacity: should be minimum 450 ml.dry weight(without cutting attachment):should not be more than 5.0 kgclutch: clutch shoe linining metal only.guide bar design: should be rollomatic type.guide bar length: guide bar length must have 50 cm/20" inch.guide bar and chain: should have same manufacture only.chain type: every drive link require groove & small oil receiver hole for better lubrication. 0.325 inch pitch & 1.6 mm thickness only. chain lubrication system: fully automatic speed controlled rotary oil pumpchain oil tank capacity: should be minimum 200 ml.oil pump drive: should have direct drive from crankshaft & oil pump flow adjustable.master lever control: must have all operation in one hand, chock, throttle, acceleration, switch off.guaranteed sound power level: should not be more than115 db(a). maximum chain velocity to iso 11681: should be minimum 28 m/s. certification: product should have valid dplf certificate with test standard en iso 11681, supply pvc pipe 1" dia made up of 1st grade

CTN :45512591

26 Jun, 2026 4.00 Lacs

Jalandhar - Punjab

Tender For corrigendum : fan belt yee bidded , sensor water temparature , pressure switch , clamp hose , solenoid , hose plain , plug pipe , shutt off valve , pressure control valve , cartridge fuel fitter , seal dust , gauge oil , element lubrication oil filter , spacer fan , gas kit , stud , nut , hose , clamp , thermo stat , plug , nipple , ben 20 , copper washer , top tank cap , radiatior top hose , flexible hose clip , radiator bottom hose , fuel stainer , return line hose , bend hose , air cleaner hose , hose air cooler , air filter element inner , air filter element outer , filter cap , fuel sensor unit , throttle cable , stack pipe , pipe exhaust , mounting bracket , rubber hose , connector , intake line hose

Corporations And Associations And Others

CTN :45651270

29 Jun, 2026 1.99 Lacs

Delhi - Delhi

Tender For supply of t and p items for ward no. 155 (mehrauli) south zone - supply of telescopic pole pruner:-specification:-pole length including blade: 6.5mblade material: hardened & tempered high carbon steel. the head of the blade shall have a hooked tip useful for cutting twigs saw blade shape: hooked type curved sawblade type & no of cutting teeth: tripple grounded 86 teeth blade length: 15"-16" pole type: light weight telescopic tubular aluminum alloy extendable pole no of positions for pole height adjustment: 10 positions locking mechanism: ergonomicvally designed two way locking mechanismtotal working length: max 219"(6623 mm), mln 103" (3103mm) branch cuttingcapacity: 200mm max, petrol operated brush cutterengine: single cylinder, 2 stroke, aircooled onlyengine displacement: 40.2ccpower output: 2kw/2.7hpmax output shaft speed at cuttingattachment: should be minimum 9000 rpmcarburetor: diaphragm with compensator technology.fuel tank capacity: minimum 600 ml.weight(dry, without cutting attachment & deflector): should not be more than 7.5 kg clutch: centrifugal type, clutch shoe support base & lining metal only. multi function handle: should have acceleration, on/off switch at right handle. brushcutter harness: should be double shoulder harness only. anti vibration system: must have 4- point aniti vibration system. vibration level in m/s2 at right handle: should not be more than 2.5 m/s2 sound pressure level db(a): should not be more than 105 db(a) drive shaft design: must have drive shaft ends square design type only.certification: must have valid en certification, petrol operated chain sawengine : single cylinder, 2stroke, aircooled onlydisplacement: 45.4cc poweroutput: 2.3kw. 3.0 hpmax. engine speed (with guide bar & chain): at least 12500 rpmcarburetor: diaphragm type compensator technology.fuel tank capacity: should be minimum 450 ml.dry weight(without cutting attachment):should not be more than 5.0 kgclutch: clutch shoe linining metal only.guide bar design: should be rollomatic type.guide bar length: guide bar length must have 50 cm/20" inch.guide bar and chain: should have same manufacture only.chain type: every drive link require groove & small oil receiver hole for better lubrication. 0.325 inch pitch & 1.6 mm thickness only. chain lubrication system: fully automatic speed controlled rotary oil pumpchain oil tank capacity: should be minimum 200 ml.oil pump drive: should have direct drive from crankshaft & oil pump flow adjustable.master lever control: must have all operation in one hand, chock, throttle, acceleration, switch off.guaranteed sound power level: should not be more than115 db(a). maximum chain velocity to iso 11681: should be minimum 28 m/s. certification: product should have valid dplf certificate with test standard en iso 11681, supply of lawn mower:-specification:- type of machine walk behind lawn mowers power sourcepetrol engine engine displacement 224ccstart type recoil / pull start, speed control variable speeddrive type all wheel drivel blade style rotary typeblade engagement electromagnetic, cut width (mm) 525 to 549, minimum cut height 20 millimetermaximum cut height 80 millimeter, blades hardened steelnumber of blades 1, number of positions for cut height adjustment 6, number of levers for cut heightadjustment: single lever, number of wheels 4front wheel size 203 millimeter, rear wheel size 250 millimeter, wheel tyres pneumaticif yes, grass catcher / collector / bag volume 70 liter, "engine power rating (watt)" 4000 to 4999, engine fuel tank capacity 1.4 ltr., supply pvc pipe 1" dia made up of 1st grade pvcspecification:- braiding with material of braiding: polyesterinner diameter(id) (mm) 25 length of pipe in a coil (in mtr.):30 wall thickness(in mm):3 color: transparent, bamboo broom with wooden handle and iron ring, supply of hessian cloth as per officer in charge

Corporations And Associations And Others

CTN :45651272

29 Jun, 2026 1.99 Lacs

Delhi - Delhi

Tender For supply of t and p items for ward no. 156 (vasant kunj) south zone - supply of telescopic pole pruner:-specification:-pole length including blade: 6.5mblade material: hardened & tempered high carbon steel. the head of the blade shall have a hooked tip useful for cutting twigs saw blade shape: hooked type curved sawblade type & no of cutting teeth: tripple grounded 86 teeth blade length: 15"-16" pole type: light weight telescopic tubular aluminum alloy extendable pole no of positions for pole height adjustment: 10 positions locking mechanism: ergonomicvally designed two way locking mechanismtotal working length: max 219"(6623 mm), mln 103" (3103mm) branch cutting, capacity: 200mm max, supply of lawn mower:-specification:- type of machine walk behind lawn mowers power sourcepetrol engine engine displacement 224ccstart type recoil / pull start, speed control variable speeddrive type all wheel drivel blade style rotary typeblade engagement electromagnetic, cut width (mm) 525 to 549, minimum cut height 20 millimetermaximum cut height 80 millimeter, blades hardened steelnumber of blades 1, number of positions for cut height adjustment 6, number of levers for cut heightadjustment: single lever, number of wheels 4front wheel size 203 millimeter, rear wheel size 250 millimeter, wheel tyres pneumaticif yes, grass catcher / collector / bag volume 70 liter, "engine power rating (watt)" 4000 to 4999, engine fuel tank capacity 1.4 ltr., petrol operated chain sawengine : single cylinder, 2stroke, aircooled onlydisplacement: 45.4cc poweroutput: 2.3kw. 3.0 hpmax. engine speed (with guide bar & chain): at least 12500 rpmcarburetor: diaphragm type compensator technology.fuel tank capacity: should be minimum 450 ml.dry weight(without cutting attachment):should not be more than 5.0 kgclutch: clutch shoe linining metal only.guide bar design: should be rollomatic type.guide bar length: guide bar length must have 50 cm/20" inch.guide bar and chain: should have same manufacture only.chain type: every drive link require groove & small oil receiver hole for better lubrication. 0.325 inch pitch & 1.6 mm thickness only. chain lubrication system: fully automatic speed controlled rotary oil pumpchain oil tank capacity: should be minimum 200 ml.oil pump drive: should have direct drive from crankshaft & oil pump flow adjustable.master lever control: must have all operation in one hand, chock, throttle, acceleration, switch off.guaranteed sound power level: should not be more than115 db(a). maximum chain velocity to iso 11681: should be minimum 28 m/s. certification: product should have valid dplf certificate with test standard en iso 11681, supply pvc pipe 1" dia made up of 1st grade pvcspecification:- braiding with material of braiding: polyesterinner diameter(id) (mm) 25 length of pipe in a coil (in mtr.):30 wall thickness(in mm):3 color: transparent, bamboo broom with wooden handle and iron ring, supply of hessian cloth as per officer in charge

State Government

CTN :45607005

02 Jul, 2026 7.50 Lacs

Jummu - Jammu And Kashmir

Tender For providing and laying of 100 mm dia g.i pipe from sump tank at cps to intake-iii for lubrication of vt pump sets along with allied works at sitlee under jmc capex (new works) 2026-27

Central Government/Public Sector

CTN :45550700

30 Jun, 2026 NA

Uttara Kannada - Karnataka

Tender For supply of carbide tipped blade chain saw - conforming standards for the item - en/din/us/equivalent standards, type of engine- 2 stroke petrol driven air cooled, displacement-79 cc, output power - 5.5 hp, engine speed at no load - 10500 rpm, type of fuel - petrol, fuel tank capacity - 0.7l, ignition system should be electronic with preferably one button start up, fully automatic and adjustable chain lubrication system, automatic chain brake system for quick stoppage when required, air filteration system for petrol engine, type of blade - carbide tipped blade, length of guard bar- 16 inch (one piece construction), adjustable depth of cut ? 6 inch, full blade guard with adjustable depth limiter in inches - 8 (minimum 1 cm adjustment), chain speed- 25 meter per second, adjustable depth of cut - 06 inch, weight of carbide tipped chain saw- 6.3 kg, cutting chain detail- carbide tipped chain with 3/8 pitch with heavy duty tie straps and tempered rivets, protective carry case should be supplied with the machine, copies of test certificates and certifications as applicable to be furnished to buyer on demand at time of supplies, demonstration of equipment and training to be provided after completing supplies,make: makita-ea7900p45e/ hikoki/ dewalt, warranty- 03 years (oem). ]

CTN :45506365

01 Jul, 2026 NA

Mumbai - Maharashtra

Tender For tender for supply of spares of helo traversing system afas ibs and machinary control and monitoring system 25blec001 c - grease nipple , hooter , mechanical lock pin limit switch , lubrication unit , pump element lub unit , spring feed lubricator , ram cylinder seal kit , o ring for straight male stud coupling 1 14 bspx30 mm od , return line case drain filter element , pressure reducing valve 1 14 nb 7 bar to 1.5 bar , replenishing low pressure inline filter element , power fuse sf94939ooo rating 160a , sea water pressure switch , aux contactor 240v 2no 2nc , bush for turret hinge , hose 07 id 12 7 x 1 5 mts lg , suction hose id- 38 1x 1 10 mts , ls hose id-7 9x 0 7 mts lg , delivery hose id 31 8 0 5 mts , return line filter , qdc p line female , qdc p line and tank line male , qdc ls and drain female , qdc ls and drain male , indication lamp green 110v ac , ss hexagon head nut grade ss316 nut size m12 , ss spring washer diameter 12 mm , mcb 2p 32a , 63a mccb 3p , mccb 160a , mccb 25a , mo0 4no contactor , mo 0 2no 2nc contactor , aux cont bl mnx 95 550 contr 2nd right , vme 10 channel serial isolator card aitech c106 , hydraulic hose pipe , pressure gague sta , 1 change over 24v dc slim relay make- finder , exhaust fan , cat 6 cable patch chord , smps for mfc processor 110 220v ac to 5vdc 4a 12v dc 1a , exhaust fan size 80x80x25 mm , pressure transmitter 0 10 bar mbs33m , pressure transmitter 0 10 bar emp 2 , dc power supply , push button , lamp , lamp , lamp , lamp , lamp , lamp , dl 100 mccb 25a , mcb hager 3p 2a c curve type ncn 302n , selector switch22.5mm type no m22 wrk4 , pressure sensor level transmitter hyd , mini terminal block 29 x 27mm ref cat no cmt4 , cont trafo 380 240v 1 5 kva bur 1500va bur ins class f frq 50hz , overload relay l t backup fuse up to 25a contactor mountin , gland packing 1 set 1x10 m , shock mounts y 450 , high tensile hex boltm20x80l , m20 spring washer , pressure gauge 100 mm dial 0 250 bar , distance tube , spacer , m20 hex nut 2 , grease nipple g1 4 , deliver hose with dko fitt both side bsp 2 id 50x5000l , lubrication unit , shock mount x 70 , male stud coupling 1 4 bsp x 10mm od , straight coupling 10 mm odx 10mm od , equal union 1 4 bsp x 1 4 bsp 60 degree cone angle , straight bulkhead coupling 10 mm odx10mm od , 1 4 bore 1 4 bsp both ends str female swivel nut len 500 mm , clamp for 10 mm od tube , bonded seal 3 8 bsp , bonded seal 3 4 bsp , bonded seal 1 1 4 bsp , bonded seal 1 1 2 bsp , bonded seal 2 bsp , 14 tp 20 atc x fe insulated cores lfh outer layer 250v , 3 core x 2 5 mm2 abc hf xlpe insulated shf2 , 24vdc omron relay socket pyf08a , plc relay 24v single contact 2 pdt 6a , 2tp x 0 5 mm2 atc hf xlpe insulated shf2 , 100a terminal block , qdc suction female , qdc suction male , axial piston pump , axial piston pump , panel pc

CTN :45384476

17 Jun, 2026 NA

Dharmapuri - Tamil Nadu

Tender For corrigendum : purchase of equipments for mechanical department - purchase of equipments for mechanical department, tail stock assembly medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, working model of fuel supply system - petrol mpfi type petrol multi point fuel injection (mpfi) system for dismantling and assembly practice system type: non-working / cut-section model for study of internal construction construction: actual automotive components or equivalent training model mounted on frame includes throttle body (sectioned), fuel injectors, fuel rail, intake manifold includes fuel pump, fuel tank (dummy), fuel filter, pressure regulator includes ignition system components: ignition coil, spark plug, distributor (if applicable) ecu module (dummy/display type) with wiring layout representation all components cut-open, painted, and clearly labelled provision for manual demonstration of flow path and component interaction mounted on rigid ms powder-coated frame designed for repeated dismantling, assembly, and component identification, hydraulic cylinderbore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply: mounted on training base suitable for dismantling and inspection, hydraulic operated directional control valves (dcv) type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study, bearing with shaft assembly type: dismantling and assembly teaching unit shaft diameter: 30 mm shaft material: en8 steel bearings: deep groove ball bearing (6205 / 6206) housing: cast iron locking arrangement: circlips end covers mounting: bench-mounted / frame mounted unit, coupling unit using driving and driven shafts using plummer block bearing unit the plummer block housing material: cast iron (grade fg 200 or equivalent). type: sng or snl series (split-type housing). sealing: felt seals or v-ring seals (to demonstrate lubrication retention). lubrication: provided with a grease nipple at the top center for manual lubrication practice. the bearing type: self-aligning ball bearing (1200 series) or spherical roller bearing (22200 series). bore diameter: standard 25mm or 30 mm. shafting and coupling shaft material: ground carbon steel (en8 or en9) for high surface finish. coupling type: flexible coupling: to demonstrate the bearings ability to handle slight misalignment. rigid flange coupling: to demonstrate traditional direct connection. driving/driven setup: one shaft connected to a small electric motor (driving) and the other to a brake drum or load (driven)., 3d printing machine build volume(wxdxh) 256 x 256 x 256 mm shell enclosed (plastic & glass) hot end all-metal nozzle 0.4 mm stainless steel included max hot end temperature 300 nozzle diameter 0.4 mm (included) 0.2 mm, 0.6 mm, 0.8 mm build plate compatibility textured pei plate, cool plate, engineering plate, high temperature plate max build plate temperature 100 max speed of tool head 500 mm/s max acceleration of tool head 20 m/s supported filament pla, petg, tpu, pva, pet, abs, asa chamber monitoring camera low rate camera 1280 x 720/0.5fps time lapse supported filament run out sensor :yes control board fan closed loop control auxiliary part cooling fan closed loop control air filter activated carbon filter

CTN :45430790

18 Jun, 2026 NA

Ariyalur - Tamil Nadu

Tender For supply of mechanical engineering lab materials - mechanical engineering lab materials, serve motor drive kitinterface l293d motor driver ic with arduino to control direction of rotation of two dc motors), bldc motor kitbldc motor 1 nobldc motor drive -1noinbuilt volt and ammeter and rpm meterinbuilt power supplyinput 230v ac, lvdt trainer kit complete educational trainer for linear variable differential transformer (lvdt) displacement measurement. built-in ac excitation source and signal conditioning circuitry for lvdt operation. micrometer assembly for precise linear movement of the lvdt core. displacement range ~10 mm with clear front-panel adjustments for zero & calibration. digital display (typically 3 -digit) for direct readout of conditioned output/displacement values. test points and banana sockets for signal observation on external instruments. self-contained unit in a durable enclosure with labeled controls and educational layout. includes user manual and patch cords for experiments. operates on 230 v ac, 50 hz mains supply., multi-cylinder petrolphase : single phase load: mechanical load with ropenumber of cylinders : 4displacement : rope brakepower : 65hp,4000 rpm,1396 ccbrand material : mild steelengine type : 4 stroke self startfrequency : 15hzfuel consumption : petrolfuel tank capacity : 5 letermorh s test rig, tail stock assemblyheavy-duty lathe tailstock assembly for training; cast iron body with base, barrel (quill) ~50 75 mm stroke, hand wheel feed, dead centre mt2/mt3, set over screws for taper turning, spindle clamp, complete with all internal parts for dismantling and reassembly; suitable for 300 400 mm centre height training lathe., dc motorvoltage 220-440 v dcpower - 180 w speed - 200 rpm, hydraulic cylinderdouble acting hydraulic cylinder, bore 40 50 mm, stroke 200 300 mm, working pressure up to 100 160 bar, steel tube with honed bore, hard chromed piston rod, front & rear end caps, piston with seals and wear rings. supplied as standalone unit with suitable mounting for dismantling, inspection and reassembly., hydraulic opreated directional control valve (dcv)manually operated 3/2 or 4/2 way spool type hydraulic directional control valve, nominal size ng06 (cetop 3) or equivalent, rated pressure 210 bar, flow 20 40 lpm; valve body with hardened and ground spool, centering springs, ports p a b t clearly marked. supplied on small mounting plate for dismantling, inspection and assembly practice., bearing with shaft assemblyteaching unit with shaft 25 35 mm dia mounted in housing with deep groove ball bearings (6205 / 6206 class) at both ends; includes locking arrangements (circlips, lock nuts, covers). designed for repeated removal, cleaning, lubrication and refitting of bearings, with provision to mount on bench or test rig., coupling unit using driving and driven shaft plumber block bearing unit1. the plummer block housingmaterial: cast iron (grade fg 200 or equivalent). type: sng or snl series (split-type housing).sealing: felt seals or v-ring seals (to demonstrate lubrication retention).lubrication: provided with a grease nipple at the top center for manual lubrication practice.2. the bearingtype: self-aligning ball bearing (1200 series) or spherical roller bearing (22200 series).bore diameter: standard 25mm or 30 mm (ideal for lab scale).mounting: adapter sleeve mounting (h-series) to teach students how to lock a bearing onto a smooth shaft.3. shafting and couplingshaft material: ground carbon steel (en8 or en9) for high surface finish.coupling type: * flexible coupling: to demonstrate the bearings ability to handle slight misalignment.rigid flange coupling: to demonstrate traditional direct connection.driving/driven setup: one shaft connected to a small electric motor (driving) and the other to a brake drum or load (driven)., spring test machine load & displacement sensing load cel * capacity: 0 10 kno accuracy: 1% fs (better if 0.5% fs) displacement sensor * lvdt / digital encodero accur

Air Receiver Spares Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Corporations And Associations And Others

Corporations And Associations And Others

Corporations And Associations And Others

State Government

Central Government/Public Sector