Tender For corrigendum : work contract for overhauling and repair/refurbishment of boiler feed pump cartridge (model fk6d30 weir make) along with supply of spares for bfp of 210 mw unit atps chachai. - impeller wear ring (eye) (1 set = 1+5 nos.) , ring section wear ring (1 set = 1+5 nos.) , impeller wear ring (neck) (1 set = 5 nos.) , diffuser wear ring (eye) (1 set = 5 nos) , thrust pads (1 set = 16 nos.) , balance drum , balance drum nut , balance drum lock washer , journal bearing glacier type de (1 set = 2 halves) , journal bearing glacier type nde (1 set = 2 halves) , o rings & back up ring , balance drum restriction bush size - 194mm , locking screws , thrust collar nut & washer , oil guard (1 set = 3 nos.) of & you , oil thrower (1 set = 3 nos.) the & then , mechanical seal complete for de & nde (make-flowserve) , copper coated gasket , set of fasteners , air breather (1set= 2 nos) , coupling nut , spring disc , thrust bearing split oil seal , thrust collar , stellite bush , dowell pin , impeller abutment ring (1 set = 5 nos.) , impeller (1 set=6 impellers) , thrust pad carrier ring for de & nde , diffuser (1 set 6 diffusers) , ring section (1set=5nos) , pump shaft keys & nuts , inboard bearing housing , outboard bearing housing , water jacket for the & you (1set=2 pcs) , suction guide seal housing with plugs de & nde (1set=2
Tender For corrigendum : procurement of spares of pembril make fluid coupling model 23scr25b of ash slurry pump for ph- ii and model 41scr 24x for ph i and ii at sgtps, birsinghpur - spares for pembril make fluid coupling (model-23scr25b) of ash slurry pump for ph-ii, input shaft, scoop housing bracket, shaft, bearing cover, bearing nut, bearing liner, set bolt, locking washer, shaft ring, if fitted, self locking nut, casing plug for cover plate, oil retaining ring, locking washer part no.56, locking washer part no. 60, scoop housing shroud, counter sunk screw, self locking nut, key woodruff, circlip, end cover, circlip external, circlip internal, scoop housing assembly, impeller, joint collector ring impeller, bonded seal part no. 196, bonded seal part no. 182f, vent tube, connecting tube, leak of nozzel, joint scoop housing bracket, feed tube, pillow block, runner baffle, set bolt, self alinging bearing, spring if (fitted), scoop pin, dowel, runner, end cover, bearing liner, spares of pembril make fluid coupling (model: 41scr-24x) for ph-i&ii, operating rod, operating lever, joint centre spigot, control lever, woodruff key, bearing liner(23124), bearing liner (nu 228), scoop housing assembly, scoop tube assembly, feed tube, leak of nozzle set, centre spigot, shaft, bearing nut, bolt for multi disc unit, self locking nut, vent tube, locking washer/star washer, allen screw for liner, .
Tender For corrigendum : supply of rotating assy for rkb,4 stage part no. ra150x34k , diffuser with guide vanes part no. 129 , enclosed impeller part no.151 , shaft sleeve s side part no. rkb15034k310 , shaft sleeve d side part no. rkb15034k311 , wear ring suc side part no. rkb15034k190 , wear ring del side part no. rkb15034k191 , suction casing part no. 113 , delivery casing part no. 111 , cooling chamber part no. 252 , bearing housing nde part no. 2401 , compression spring part no. 483 , thrust bearing adaptor part no. 272ms , bearing cartridge nde part no. bcrkb150x34
Tender For straightening of s.s. shafts, cutting and removing of worn out sleeves, removing of muff couplings and dynamic balancing of impeller of vertical turbine pump no.22 at m-3a pumping station, pisebid no.: 2026_mcgm_1306255
Tender For straightening of ss shafts cutting n removing of worn out sleeves removing of muff couplings and dynamic balancing of impeller of vertical turbine pump no 24 at m-3a pumping station pise - straightening of s.s. shafts, cutting & removing of worn out sleeves, removing of muff couplings and dynamic balancing of impeller of vertical turbine pump no.24 at m-3a pumping station, pise.
Tender For procurement of spares of everllence make lp and hp compressors of process air compressor- lpc journal bearing shoe set, 1 set 04 nos. of shoe pads; sectiona dwg no. 1-2559345.3, identification no. 23-1734-17-110-01-001.1 part no.- 10.17.1 for non driving side and part no.:10.17.2 for drive en side, dimension-type tr4sl140; material-st/tego v738; requirement i 01 set for nde side and one set for de side pads including temperatur sensors, hpc journal bearing shoe set, 1 set 04 nos. of shoe pads; sectiona dwg no. 1-25593464, identification no. 23-1736-17-110-01-001.1 part no. 10.17.1 for non-drive end and 10.17.2 for drive enc dimension-type tr4sl100; material-st/tego v738; requirement is 0 set for nde side and one set for de side including temperature sensor, impeller seal third stage; doc. no- 1-25593464; identification no. 23 1736-13-130-03-803; part no- 10.13.14; pos/tag no: hp-k3421