Latest air shaft Tenders | Government air shaft Tenders

corporations/Associations/Others

CTN :45732590

20 Jul, 2026 NA

Kolkata - West Bengal

Tender For procurement of: consumables and spares of secondary fully automatic big bag packing machine - vertical jaw complete (heater, sensor, smc connector with pvc pipe) , horizontal rear jaw complete (heater, sensor, smc connector with pvc pipe) , horizontal front jaw complete (heater, sensor, smc connector with pvc pipe) , a0199833898c26c rear jaw for ldpe double band , a0199833908c26b front jaw for ldpe double band , akc0204003zz260 vertical jaw , a019983395eq03a rear c block for oi-5263 , a019983396eq03a front c block for 01-5263 , bfjb01010304000 air shaft for excel 400 plus , a01998326322990-thermocouple , ace02000352299a -thermocouple , a010200011ah998 heater for vertical seal a 3/8, 510l,600w, 230v , a010300014ah998 heater for horizontal seal a 3/8, 418l, 400w, 230v , aaf0300003bk990 knife (3mm thk) , a019983392ab070 locking pin for oi-5263 , a010715010yy02d tension spring for dancer , a030400008bc26a driver pulley for belt draw off , a260400006zz99a timing belt assly , a0413000228c26c driven pulley , bdph01030307600 timing belt 285-l-100 mbl make , a0441000162299a camozzi double acting cyl 61m2p080a0080 , akc0702012zz990 motor pulley , akc2506002bc260 tension pulley , baar07697000006 needle roller bearing hk 1210 , bcpb11411211205 camozzi short stroke single acting , bcp813441121016 camozzi double acting cyl dia 32 x 80 , bcpb41001100030 camozzi-single sol vlv-5/2 way-1/8 , bcpb41002100030 camozzi-single solonoid valve-3/2 way , bcpb41391208220 camozzi solonoid valve-5/2 way-1/4 , bcp853351000000 camozzi sealing ring 2661-1/8 , eatj01112705332 switch selector switch 3 pos

CTN :45678714

11 Jul, 2026 5.50 Lacs

Saharanpur - Uttar Pradesh

Tender For supply of wooden hand wire brush 3 inch x 6 inch , teflontape 3or4inch x 10mtr , rustolene pidilite make 500ml , holdite 500 gm pack pidilite make , grinding wheel ag 4 inch carborandum universal make , grinding wheel ag 7 inch carborandum universal make , brasso liqued in tin of 100 ml , araldite in 1.80 kg , emery cloth in 500 sheet fine carborandum universal make , emery cloth in 500 sheet rough carborandum universal make , emery tape 50 mtr roll size 2 inch fine carborandum universal make , emery tape 50 mtr roll size 2 inch roughcarborandum universal make , cotton waste , m seal 1 kg pack astralorpidiliteor m m make , blue tube 15ml atlas orcamel make , piano wire , graphite powder fine , hacksaw blade double side 1or2inch x 12 inch hss miranda make , hacksaw blade double side 1or2inch x 12 inch low carbon steel , marken cloth cotton , conical grinding wheel 1inch x 2inch , grinding wheel 1.5 inch , buffing wheel 4inch for ag 4 grinder boschor dewalt make , cutting wheel 4inch for ag 4 grinder boschor dewalt make , cutting wheel 14inch boschor dewalt make , silicon brazing rod size 3mm , klinger make b-9 borocilicate gauge glass imported and plane , stainless steel plate grade 304 plain sheet size 4 feet x 8 feet x 3 mm thickness , anabond 112 thread locker 50 ml , loctite 609 retaining compound in 50ml , loctite 641 retaining compound in 50 ml , emery paste rough 400 gm carborandum universal make , emery paste fine 400 gmcarborandum universal make , brass solid round bar extruded quality size 20mm od , brass solid round bar extruded quality size 25mm od , brass solid round bar extruded quality size 50mm od , boiler gauge glass bishop make size 3or4inch x 16.5 inch , boiler gauge glass bishop make size 3or4inch x 22.5 inch , solenoid valve with coil rotex make model no 3012 two way , solenoid valve with coil rotex make model no 3013 one way , stag jointing paste type b red in 1 kg pack , galva coating gcs 73 bright finish make aerotech 500 ml , grinding wheel black for bench grinding machine size 1.5inch x1.5 xinch x12inch , grinding wheel green for bench grinding machine size 1.5inch x1.5 xinch x12inch , usha martin make steel wire rope 3or4inch,6or36 construction hemp core with test certificate 305mtr in one roll , love joy coupling set l-70 , love joy coupling set l-75 , love joy coupling set l-90 , love joy coupling set l-100 , love joy coupling set l-110 , spring washer bbbb make size 3or8 inch 100 piece per pack , spring washer bbbb make size 1or2 inch 100 piece per pack , spring washer bbbb make size 5or8 inch 100 piece per pack , spring washer bbbb make size 18mm 100 piece per pack , split pin champion make size 1or4 inch x 2 inch 100 piece per pack , split pin champion make size 1or4 inch x 2.5 inch 100 piece per pack , split pin champion make size 1or4 inch x 3 inch 100 piece per pack , anabond 666-250ml , leather hand gloves pair ador or asha make , rubber star for coupling set l-70 , rubber star for coupling set l-90 , rubber star for coupling set l-100 , rubber star for coupling set l-110 , paint brush size 2inch , paint brush size 3inch , paint brush size 4 inch , red oxide primer british paint-asian make 20ltr drum , borex powder suhaga , graphite fire crucible 120 kg ,make india super -double kabootar , ss flat grade -305 size -12mm x 65mm , silver rustam brazing flux 500gm , sleeve 3or4 inch nationalorleader make for tubular gauge glass , rubber cone 3or4 inch nationalorleader make for tubular gauge glass , flexible hand grinder for 2 inch wheel sf-2 model alond with shaft raly wolf 10fd accessories , wire rope u clamp heavy duty size 3or4inch , monarch save past tpxt-high temp titanium putty ,working temp 500centi complete kit , needle roller bearing axk4060 with sleeve , needle roller bearing axk7095 with sleeve , needle bearing ba1816 with sleeve , rubber oil seal 65x85x10 spring loaded oskoorsunnyormykoda make , rubber oil seal 42x55x8 spring loaded oskoorsunnyormykoda make , rubber oil seal 42x72x10

Corporations And Associations And Others

CTN :45651274

29 Jun, 2026 1.99 Lacs

Delhi - Delhi

Tender For procurement t and p items for ward no. 151 (munirka) south zone - supply of telescopic pole pruner:-specification:-pole length including blade: 6.5mblade material: hardened & tempered high carbon steel. the head of the blade shall have a hooked tip useful for cutting twigs saw blade shape: hooked type curved sawblade type & no of cutting teeth: tripple grounded 86 teeth blade length: 15"-16" pole type: light weight telescopic tubular aluminum alloy extendable pole no of positions for pole height adjustment: 10 positions locking mechanism: ergonomicvally designed two way locking mechanismtotal working length: max 219"(6623 mm), mln 103" (3103mm) branch cuttingcapacity: 200mm max, petrol operated brush cutterengine: single cylinder, 2 stroke, aircooled onlyengine displacement: 40.2ccpower output: 2kw/2.7hpmax output shaft speed at cuttingattachment: should be minimum 9000 rpmcarburetor: diaphragm with compensator technology.fuel tank capacity: minimum 600 ml.weight(dry, without cutting attachment & deflector): should not be more than 7.5 kg clutch: centrifugal type, clutch shoe support base & lining metal only. multi function handle: should have acceleration, on/off switch at right handle. brushcutter harness: should be double shoulder harness only. anti vibration system: must have 4- point aniti vibration system. vibration level in m/s2 at right handle: should not be more than 2.5 m/s2 sound pressure level db(a): should not be more than 105 db(a) drive shaft design: must have drive shaft ends square design type only.certification: must have valid en certification, telescopic petrol operatedpole prunerengine: single cylinder, 2 stroke, air cooled onlydisplacement: should be between 25-30 ccpower output: should be minimum 1.2 hpweight (dry without cutting attachment & fuel): should not be more than 7.5 kgfuel tank capacity (ml): should be minimum 400mlchain oil capacity (ml): must have minimum 200 ml.clutch: clutch shoe linining should be metal only.guide bar length: minimum 30cmguide bar and chain: should have same manufacture onlychain type: every drive link need groove & small oil holes for better lubrication. saw chain pitch should be 1/4" or 3/8picco only and drive link thickness must have 1.1 mm or 1,3 mm.max. output shaft speed (rpm): should be minimum 8000 rpm at chain sprocket.equipment total length with guide bar and chain (cm): should be minimum 220 cm - compressed & total length of equipment -minimum 350 cm - extended.sound pressure level (db/a): should not be more than 95 db(a)vibration measurement m/s2 at control handle extended position: should not be more than 5.5 m/s2certification: must have tuv certification with test standard en iso 11680, petrol operated chain sawengine : single cylinder, 2stroke, aircooled onlydisplacement: 45.4cc poweroutput: 2.3kw. 3.0 hpmax. engine speed (with guide bar & chain): at least 12500 rpmcarburetor: diaphragm type compensator technology.fuel tank capacity: should be minimum 450 ml.dry weight(without cutting attachment):should not be more than 5.0 kgclutch: clutch shoe linining metal only.guide bar design: should be rollomatic type.guide bar length: guide bar length must have 50 cm/20" inch.guide bar and chain: should have same manufacture only.chain type: every drive link require groove & small oil receiver hole for better lubrication. 0.325 inch pitch & 1.6 mm thickness only. chain lubrication system: fully automatic speed controlled rotary oil pumpchain oil tank capacity: should be minimum 200 ml.oil pump drive: should have direct drive from crankshaft & oil pump flow adjustable.master lever control: must have all operation in one hand, chock, throttle, acceleration, switch off.guaranteed sound power level: should not be more than115 db(a). maximum chain velocity to iso 11681: should be minimum 28 m/s. certification: product should have valid dplf certificate with test standard en iso 11681, supply pvc pipe 1" dia made up of 1st grade

State Government

CTN :45667106

30 Jun, 2026 NA

Multi City - Telangana

Tender For supply of spares of packing machine 2.5 kg 1.2kg - web belt-285l (paper pulling belts), timing belt,width-25mm, type-at10, length-800, item code-dt10149, timing belt-width -50mm, type at10,length-1940mm, item code-dt10113, timing belt-210l (3/8 inchpx56 teethx3/4inch width), item code-dt10047, timing belt-240lx19wx3/8inch p,item code-dt10127, horizontal heaters-3/8x270l 170vx225w drawing no.509sk82848, vertical seal heater 110v 500w 420lg, item code -fh10233, drawing no -5090200006, vibrating fork level sensor, lsv-t1-h0-g4-pb2+nfl-c4-ei-oul200, item code-elv0078, paper mark sensor datasensor make (i-sensor), item code -epm0013, photo electric sensor, model no:bup-30-p, item code -esp0108, thermocouple, item code- fh10011a, drawing no -750200035a, rod type sensor item code -fh10043c, drawing no -4041100013c, proximity sensor-m18 std pnp, diffused ir sensor, m 18/65, pnp, 10, item code -esp0080, encoder, item code - fp10277, camozzi -double acting cyl dia 32, stroke-20, 31f2a032a020, item code - nc10363 for horizontal jaw, camozzi -qn1a32a10 short stroke single acting cyl -dia 32 stroke 10,item code -nc10279 for knife, camozzi - 31m2a025a080 compact double acting cyl. dia 25 stroke x 80, item code - nc10500 for web, camozzi -31m2a032a015 compact double acting cyl magnetic dia.32 stroke 15, item code - nc10476 for break, camozzi - single solonoid valve-5/2 way-1/8 with 24 dc coil-358-015-02-u77, item code - nv10234, camozzi - single solonoid valve-3/2 way-1/8 with 24 dc coil-338l-015-02-u77, item code - nv10236, knife guide item code - cd45505b, drawing no -1010600002b, knife guide plate, item code - cd60108, drawing no -509sk77470, spline shaft (2-dpm 1530+570l thk) item code - cd63442a, drawing no -5090405000a, driving shaft item code - cd53126b, drawing no -4960400011b, worm gear box-vf44v 7 hs b3,item code - fg10060, worm gear box shaft item code - cd32708b, drawing no -316sk56171b, driven bevel gear, item code - cd38690a, drawing no -3661300017a, driving bevel gear item code - cd38689b, drawing no - 3661300016b, worm bonfiglioli gear motor 20:1, 0.18 kw , vf30f1-20p63b5v6 + bn63b4,item code - fg20066, sprocket 19 teeth 1/2 pitch,item code:cs30182, drawing no:260sk23375, sprocket 1/2 inch p x 38 teeth (plate type) item code:cs30049a, drawing no: 06090049a, chain simplex 1/2inch pitch,item code: cc10001, coupling od 27mm x id 19 mm x 40 mm lg, item code - cc20046, spline shaft nut, item code - bl20014, needle roller bearing hk 1612 ntn make, item code -bn10053, deep groove ball bearing 61808 zz skf, item code -bb10227, bearing (skf) 608 zz, item code - bb10058, pivot pin long item code - cd63926, drawing no -509sk80490, spacer for rear jaw 25 lg item code - cd63633a, drawing no -509sk80366a, spacer for front jaw 17 lg, item code - cd63632a, drawing no -509sk80365a, crank drive shaft, item code -cd58348c, drawing no -5091400004c, compression spring, item code -cs40423, drawing no -1010600013, tension spring, item code -cs40428c, drawing no -5040715010c, tension spring for dancer, item code -cs40434a, drawing no -5092203003a, knife, item code -ck20210, drawing no -509sk82125, knife holders (knife guide pin-a),item code:cd45508, drawing no:104sk64104, knife holders (knife guide pin-b),item code:cd60107, drawing no:509sk77473, vigor make, programmable controller,model no.vb-1pg, unison-ssr, 25amp, model 801 zda 48 25 01, output ac voltage 24-480vac., barings and bushes, vertical sealing assembly, videojet tto 6210 printer rubber pads, schneider electric encoder cable-5m, 3x2x0.14 mm2 +2x0.34 mm2 shielded, motor end 12-pin circular connector m23,device end 10-pin connector rj45, order no.vw3m8102r50 for servo drive lxm32cd30n4, schneider make, 3n lug type pneumatic air shaft code no.cm10390, drawing no.5095k76930, temperature controller model no.sr1, shimaden make, auger for 2.5kg item code:-ca32408,drawing no.509sk82247, gear moter bn80b4, kw-0.75, rpm 1400 item code -em40236

Corporations And Associations And Others

CTN :45651270

29 Jun, 2026 1.99 Lacs

Delhi - Delhi

Tender For supply of t and p items for ward no. 155 (mehrauli) south zone - supply of telescopic pole pruner:-specification:-pole length including blade: 6.5mblade material: hardened & tempered high carbon steel. the head of the blade shall have a hooked tip useful for cutting twigs saw blade shape: hooked type curved sawblade type & no of cutting teeth: tripple grounded 86 teeth blade length: 15"-16" pole type: light weight telescopic tubular aluminum alloy extendable pole no of positions for pole height adjustment: 10 positions locking mechanism: ergonomicvally designed two way locking mechanismtotal working length: max 219"(6623 mm), mln 103" (3103mm) branch cuttingcapacity: 200mm max, petrol operated brush cutterengine: single cylinder, 2 stroke, aircooled onlyengine displacement: 40.2ccpower output: 2kw/2.7hpmax output shaft speed at cuttingattachment: should be minimum 9000 rpmcarburetor: diaphragm with compensator technology.fuel tank capacity: minimum 600 ml.weight(dry, without cutting attachment & deflector): should not be more than 7.5 kg clutch: centrifugal type, clutch shoe support base & lining metal only. multi function handle: should have acceleration, on/off switch at right handle. brushcutter harness: should be double shoulder harness only. anti vibration system: must have 4- point aniti vibration system. vibration level in m/s2 at right handle: should not be more than 2.5 m/s2 sound pressure level db(a): should not be more than 105 db(a) drive shaft design: must have drive shaft ends square design type only.certification: must have valid en certification, petrol operated chain sawengine : single cylinder, 2stroke, aircooled onlydisplacement: 45.4cc poweroutput: 2.3kw. 3.0 hpmax. engine speed (with guide bar & chain): at least 12500 rpmcarburetor: diaphragm type compensator technology.fuel tank capacity: should be minimum 450 ml.dry weight(without cutting attachment):should not be more than 5.0 kgclutch: clutch shoe linining metal only.guide bar design: should be rollomatic type.guide bar length: guide bar length must have 50 cm/20" inch.guide bar and chain: should have same manufacture only.chain type: every drive link require groove & small oil receiver hole for better lubrication. 0.325 inch pitch & 1.6 mm thickness only. chain lubrication system: fully automatic speed controlled rotary oil pumpchain oil tank capacity: should be minimum 200 ml.oil pump drive: should have direct drive from crankshaft & oil pump flow adjustable.master lever control: must have all operation in one hand, chock, throttle, acceleration, switch off.guaranteed sound power level: should not be more than115 db(a). maximum chain velocity to iso 11681: should be minimum 28 m/s. certification: product should have valid dplf certificate with test standard en iso 11681, supply of lawn mower:-specification:- type of machine walk behind lawn mowers power sourcepetrol engine engine displacement 224ccstart type recoil / pull start, speed control variable speeddrive type all wheel drivel blade style rotary typeblade engagement electromagnetic, cut width (mm) 525 to 549, minimum cut height 20 millimetermaximum cut height 80 millimeter, blades hardened steelnumber of blades 1, number of positions for cut height adjustment 6, number of levers for cut heightadjustment: single lever, number of wheels 4front wheel size 203 millimeter, rear wheel size 250 millimeter, wheel tyres pneumaticif yes, grass catcher / collector / bag volume 70 liter, "engine power rating (watt)" 4000 to 4999, engine fuel tank capacity 1.4 ltr., supply pvc pipe 1" dia made up of 1st grade pvcspecification:- braiding with material of braiding: polyesterinner diameter(id) (mm) 25 length of pipe in a coil (in mtr.):30 wall thickness(in mm):3 color: transparent, bamboo broom with wooden handle and iron ring, supply of hessian cloth as per officer in charge

CTN :45592377

04 Aug, 2026 NA

Delhi - Delhi

Tender For procurement of spares for m53 p2 aero engine - bush, nut,double hexagon, pin,cotter, socked matched, cap,blanking, washer,flat, coil, electrical, connector,plug,electrical-without contact, connector,plug,electrical, plate, packing, preformed, packing, preformed, ring,lock, braid,tubular,copper,tin-plated, bellows,motor,ps4, bellows assembly, bolt,drilled,hexagon head, bolt,drilled hexagon head, screw,machine, bolt,double,hexagon head, bolt,drilled double hexagon head, nut,hexagon,thin, bracket, stop,spring, cover, washer , flat, coupling, cover, outer liner, screw,countersunk head, cover, access, cover, plate, insert,screw adjusting, plate identification, cover, access, bush, cap, nipple, nipple, spring, plug, valve union,quick-connect, connection, bolt,double hexagon head, cap,blanking, screw,cheese head,flat, strainer, seal, filter,fuel, shaft, long, bolt,drilled double hexagon head, nut hexagon, retainer nut, damper,blade-stages 4 and 5, washer,shouldered, pin, gasket, strip,bonding, plate,blanking, plug, cover, seat,spring, nut, segment, connection,elbow,rear, connection,straight,rear, douille, plug, plate,blanking, spring,helical,compression, end-stop,spring, valve, washer lock, nut plain hexagon, bolt,hexagon head, spring, connector,plug,electrical, connector,plug,electrical-without contact, connector,plug,electrical-without contact, sheath heat shrinkable

CTN :45488935

30 Jun, 2026 41.38 Lacs

Murshidabad - West Bengal

Tender For procurement of esp spares for unit 4 esp overhauling during under ahp-em,stage ii during 2026,sgtpp - procurement of esp spares for unit 4 esp overhauling during under ahp em ,stage ii during 2026,sgtpp, ci bearing,collecting rapping ( plain bearing (ci) for crm & erm system,mat-is-210 gr-20 with 02 nos bolt, id-51 mm and 50 mm thickness. ), ci bearing for erm vertical shaft for esp dia-40mm. ( bush along with outer assembly. ), set ring for bush bearing for esp for 500mw esp, thrust bearing of em vertical rapping shaft ( mat-en-8. ), bottom bearing # of em rapping vertical shaft, major pin wheel big ( mat- pin en-8 with hardness -300-350 bhn, body-is-2062(assly). ), minor pin wheel small ( mat- pin en-8 with hardness -300-350 bhn, body-is-2062(assly). ), heating element for esp hopper for esp for 500mw esp. ( 440vac,for 500mw bhel esp, rating-500w. ), heating element for shaft insulator for esp for 500mw esp. ( for 500mw bhel esp, rating -1.0kw,type- breathing type tubular, 415v. ), heating element for support insulator for esp for 500mw esp., shaft insulator for esp for esp for 500mw esp. ( suitable for 500mw esp,make-m/s. bhel. ), support insulator, type-cylindrical for esp for 500mw esp ( od: 435 + 10 mm; id: 379 + 10 mm; height: 375 + 5 mm,for 500 mw bhel make esp. ), anvil for shock bar assembly #, inner arm for rapping hammer for esp moc-en 8 ( inner arm(ms) for rapping hammer suitable for m/s. bhel make esp ,2x500mw. ), emitting electrode for 500mw esp for esp model faa-9x45m-2x100150-2, hammer assembly,em rapping system # ( outer arm/hammer for eerm of 500 mw bhel make esp ), hammer assembly,col rapping system # ( outer arm/hammer for cerm of 500 mw bhel make esp ), pin insulator for disconnecting switch for esp c.no-71-999, crm horizontal shaft, dia-50mm for esp shaft 1-3 length -4250mmrnshaft 2-3 length -4650mmrnshaft 3-3 length -4790mm ( moc- en8, 400 mm pitch, as per drg. no: 2-79-725-04299 of 500mw bhel unit. section: 02,03 & 04. sleeve tube to be given seperate 04 nos. per set. ), shaft,end,d50xl940mm,en8 w/key&key slot for esp cerm shaft as per bhel drg no: 2-79-725-04299 ( moc: en8 ), shaft,eerm shaft,vertical,dia-40mm for esp 9900mm long,with sleeve,moc-en8 or080m40-bs970 or equivalent ( for 500 mw bhel make esp ), shaft,eerm shaft,horizontal,dia-50mm for esp 9270mm long,with sleeve and set rings,moc-en8 or080m40-bs970 or equivalent ( 03 parts(part-i with key,part-ii & part-iii) with 02 number set ring,02 number sleeve.bhel drawing no.-2-79-716-03812. ), gdrm d-50 shaft moc-en-8 with 19 holes for 500 mw esp serial no-faa-9x45m-2x100150-2 , 3 parts shaft with 19 holes.shaft with sleeve and set rings., big hammer for cerm shaft for 500 mw esp serial no-faa-9x45m-2x100150-2 drg no:2-79-725-04299

Corporations And Associations And Others

CTN :45328794

11 Jun, 2026 19.95 Lacs

Delhi - Delhi

Tender For corrigendum : providing t and p items and garden tools for ward no. 171 (cr park) south zone - providing t & p items and garden tools for ward no. 171 (cr park) south zone., supply of telescopic pole pruner:-specification:-pole length including blade: 6.5mblade material: hardened & tempered high carbon steel. the head of the blade shall have a hooked tip useful for cutting twigssaw blade shape: hooked type curved sawblade type & no of cutting teeth: tripple grounded 86 teeth blade length: 15"-16"pole type: light weight telescopic tubular aluminum alloy extendable poleno of positions for pole heightadjustment: 10 positionslocking mechanism: ergonomicvally designed two way locking mechanismtotal working length: max 219"(6623 mm), mln 103" (3103mm) branch cuttingcapacity: 200mm max, petrol operated brush cutterengine: single cylinder, 2 stroke, aircooled onlyengine displacement: 40.2ccpower output: 2kw/2.7hpmax output shaft speed at cuttingattachment: should be minimum 9000 rpmcarburetor: diaphragm with compensator technology.fuel tank capacity: minimum 600 ml.weight(dry, without cutting attachment & deflector): should not be more than 7.5 kgclutch: centrifugal type, clutch shoe support base & lining metal only.multi function handle: should have acceleration, on/off switch at right handle.brushcutter harness: should be double shoulder harness only.anti vibration system: must have 4- point aniti vibration system.vibration level in m/s2 at right handle: should not be more than 2.5 m/s2sound pressure level db(a): should not be more than 105 db(a)drive shaft design: must have drive shaft ends square design type only.certification: must have valid en certification, telescopic petrol operatedpole prunerengine: single cylinder, 2 stroke, air cooled onlydisplacement: should be between 25-30 ccpower output: should be minimum 1.2 hpweight (dry without cutting attachment & fuel): should not be more than 7.5 kgfuel tank capacity (ml): should be minimum 400mlchain oil capacity (ml): must have minimum 200 ml.clutch: clutch shoe linining should be metal only.guide bar length: minimum 30cmguide bar and chain: should have same manufacture onlychain type: every drive link need groove & small oil holes for better lubrication. saw chain pitch should be 1/4" or 3/8picco only and drive link thickness must have 1.1 mm or 1,3 mm.max. output shaft speed (rpm): should be minimum 8000 rpm at chain sprocket.equipment total length with guide bar and chain (cm): should be minimum 220 cm - compressed & total length of equipment -minimum 350 cm - extended.sound pressure level (db/a): should not be more than 95 db(a)vibration measurement m/s2 at control handle extended position: should not be more than 5.5 m/s2certification: must have tuv certification with test standard en iso 11680, supply of lawn mower:-specification:- type of machine walk behind lawn mowers power sourcepetrol engine engine displacement 224ccstart type recoil / pull startspeed control variable speeddrive type all wheel driveblade style rotary typeblade engagement electromagneticcut width (mm) 525 to 549minimum cut height 20 millimetermaximum cut height 80 millimeterblades hardened steelnumber of blades 1number of positions for cut height adjustment 6number of levers for cut heightadjustment: single levernumber of wheels 4front wheel size 203 millimeterrear wheel size 250 millimeterwheel tyres pneumaticif yes, grass catcher / collector / bag volume 70 liter"engine power rating (watt)" 4000 to 4999engine fuel tank capacity 1.4 ltr., supply of synthetic enamel paint in all shades as per required and direction of officer-in-charge., petrol operated chain sawengine : single cylinder, 2stroke, aircooled onlydisplacement: 45.4cc poweroutput: 2.3kw. 3.0 hpmax. engine speed (with guide bar & chain): at least 12500 rpmcarburetor: diaphragm type compensator technology.fuel tank capacity: should be minimum 450 ml.dry weight(without cutting attachment):should not be mor

Central Government/Public Sector

CTN :45002291

05 Jun, 2026 NA

Bhopal - Madhya Pradesh

Tender For bid to ras corrigendum : supply of # 01-tubular shaft assembly complete with fabrication and machining as per annexure-i , # 02- top oil retainer assy complete with fabrication and machining as per annexure-i

CTN :45044595

29 May, 2026 NA

Pune - Maharashtra

Tender For bid to ras supply of mt spare d d - pipe union pressure regulator union , 10333358 lv7 zil 130 3430139 intermediate cover sealing ring , 10333359 lv7 zil 130 3430012 steering booster control valve set assy , 10333608 lv7 zil 130 6104011 left hand window raiser assy , 10333642 lv7 zil 130 5206054 sealing strip lock , 10333664 lv7 zil 130 6105029 left hand latch assy , 10333667 lv7 zil 130 6105013a left hand lock assy , 10334008 lv7 zil 131 1804040 lever transfer case control lever , 10334083 lv7 zil 131 1804173 shackle , 10334086 lv7 zil 131 1804316 hose assy from tfr case control valve , 10334087 lv7 zil 131 1804319 tfr case control valve connecting hose , 10334825 lv7 zil 306647 p main shaft front roller bearing , 10335468 lv7 zil 131 1800010 transfer case parking brake assy , 10335728 lv7 zil 130 6105081 a left hand door lock control linkage assy , 10336719 lv7 zil 131 4501046 gasket , 10336932 lv7 zil 255128 p tubular round head , 10337265 lv7 zil 130 5001364 b cab middle support lower pad assy , 10337269 lv7 zil 262514 p plug , 10338104 lv7 zil 164 6104055 window regulator brk mech spring head , 10338339 lv7 zil 130 8401305 radiator grill sealing strip seal , 10338438 lv7 zil 130 8402530 rh hood mounting linkage assy , 10338458 lv7 zil 130 8402531 lh hood mounting linkage assy , 10340615 lv7 zil 421174 p brake valve elbow 3 8 , 10341084 lv7 zil 130 1701086 bush , 10341103 lv7 zil 130 1602126 fork sealing ring bushing assy flange , 10341108 lv7 zil 131 3801010 instrument pannel for lot 1 , 10341223 lv7 zil 130 1701127 gear second speed secondery shaft , 10341389 lv7 zil 131 3733010 electromagnetic assy rs 326 , 10341490 lv7 zil 130 1701059 bushing , 10341619 lv7 zil 130 1701021 hatch cover gasket , 10343551 lv7 zil 131 5130037 power take off lever hatch sealing , 10343619 lv7 zil 157u 3802046 bushing , 10344427 lv7 zil 307291 p oil seal outer cup , 10344542 lv7 zil 307743 p locking ring rear bearing lock ring , 10345173 lv7 zil 300275 p8 through union , 10346127 lv7 zil 131 3713230 b instrument pannel illumination lamp , 10346145 lv7 zil 130t 3801010 b instrument pannel type kp 204 assy , 10346197 lv7 zil 130v 6105030 rh striker assy , 10346224 lv7 zil 200376 p8 shackle to floor attachment bolt , 10347301 lv7 zil 305000 p plug , 10367772 lv7 zil 122 2104136 yoke threaded high and low ranges contr , 10543367 lv7 zil 130 5206010 wind shield right hand glass , 10544428 lv7 zil 258257 p2 1 lock wire wire catter pin , 10559703 lv7 zil 131 4202010b single speed pto assy no 01 , 10565024 lv7 zil 131 1702220 b2 gear shift lever assy , 10565027 lv7 zil 131 4202375 chamber diaphragm , 10321065 lv7 zil 131 2919011 a rear suspensing torque rod with pin , 10339426 lv7 zil 130 6804010 mechanism rh assy , 10336979 lv7 zil 130 3003056 steering tie rod right hand end assy , 10339445 lv7 zil 130 6804011 mechanism lh assy lv7/zil fg73711300g moulding ring external assy, lv7/zil fg122-3711300-b head lamp mounting, lv7/zil pd20-3803000-d(zil) turn indicator pilot lamp type pd20d, lv7/zil 301375-p8 bolt, lv7/zil 130-6103680 vent window shut sealing strip, lv7/zil 130-6103645 vent window glass gasket 2.0mm thick, lv7/zil 130- 6103254 drop window sealing strip assy, lv7/zil 131- 3105819-b right hand hoist nut, lv7/zil 131-3105841 //bid details 2 / 63

Air Shaft Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

corporations/Associations/Others

Corporations And Associations And Others

State Government

Corporations And Associations And Others

Corporations And Associations And Others

Central Government/Public Sector