Latest alloy steel tube Tenders | Government alloy steel tube Tenders

State Government

CTN :43467490

13 Jan, 2026 NA

Delhi - Delhi

Tender For s/i/t/c of e/m equipments and allied works for newly re-bored tube well at okhla vihar near majar in okhla constituency ac-54. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 15 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point: 200-125-75 lpm on 89-124-133 mtr. head.having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved. , supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted. a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no. b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 no c) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no. e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable banking g) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos.complete wiring &installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated and pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs. make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., supply of ms nut bolts off size as per requirement., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 1x1 made out from 6mm thick m.s. sheet in 2 halves and a circular hole in centre 3-1/2 dia. with locking arrangement by nuts and bolt. , earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.

Central Government/Public Sector

CTN :43378896

14 Jan, 2026 NA

Guna - Madhya Pradesh

Tender For corrigendum : tender for supply of bearing -cylindrical roller bearing , single row , bearing designation/number-skf nu311 ecj or equivalent , cage material- steel , make- fag/skf/ntn , single row angular contact ball bearing no.7311 bdb c3 or 7311 b-jp-ua or skf 7311 bmp or equivalent (steel/brass cage) , make- skf/ntn/fag , cylindrical roller bearing , single row. bearing designation / number- skf nu207 e/ fag nu207e.tvp2 / ntn nu207e or equivalent make- skf /fag / ntn. cage material- steel , cylindrical roller bearing , nu211 b or equivalent , cage material- steel/brass , make- skf / fag / ntn only , angular contact ball bearing. single row. bearing designation / number , fag 7309 b.tvp.ua / skf 7309 bpg /ntn 7309 b.t2.d2 , make- fag / skf /ntn only , self aligning ball bearing , double row , bearing designation / number- skf 2310 m / ntn 2310 s , or equivalent cage material- steel , make- skf / ntn /fag , cylindrical roller bearing , single row , bearing designation / number- skf nu307.c3 ecp or equivalent , cage material- steel , make ntn/fag/skf only , angular contact ball bearing no. skf 7307bec / fag 7307 b.tvp / ntn 7307c , or equivalent , (steel/brass cage) , make- skf / fag / ntn only , angular contact ball bearing , single row , bearing designation /number- skf 7206 b or equivalent , cage material- ss , make- ntn. , angular contact ball bearing , single row , bearing designation / number- skf 7308becb / fag 7308b.tvp.ua /ntn 7308bdb c3 or equivalent , make- skf / fag / ntn , spherical roller bearing , double row , bearing designation / number- fag 22216 e1.c3 / skf 22216 e.c3/ ntn 22216 b.d1.c3 , make- ntn/skf/fag only , deep groove ball bearing , single row , bearing designation / number- fag 6213 c3 / skf 6213 c3 / ntn 6213 c3 , make- fag / skf / ntn , deep groove ball bearing with pressed steel cage , bearing designation/ number- 6212. c3 of fag , skf or ntn make only , cylindrical roller bearing , single row , bearing designation / number- skf nu308 / fag nu308 / ntn nu308 or equivalent , make- skf /fag / ntn with steel cage. , spherical roller bearing with taper bore , double row , bearing designation/number- skf 22211ek /fag 22211e1k / ntn 22211ek , cage material- steel , make- skf/fag/ntn only , spherical roller bearing with taper bore , double row , bearing designation/number- skf 22209ek /fag 22209e1k / ntn 2209ek , cage material- steel , make- skf/fag/ntn only , adapter sleeve , designation- h-311 suitable for bearing 22211k adapter sleeve (taper sleeve along with lock nut & lock washers) , make- skf /fag/ntn only , adapter sleeve (taper sleeve along with lock nut & 2 lock washers) , designation- h-316 , suitable for bearing 22216k , make- skf/fag/ ntn only , adapter sleeve , designation- h 309 , suitable for bearing 22209k adapter sleeve (taper sleeve along with lock nut & 2 lock washers) , make- skf/fag/ntn only , spherical roller bearing , double row metallic cage , with circular groove & lubricating holes on the outer ring bearing designation/number skf22322 e c3 , fag22322 e1 c3 , ntn22322 bd1 c3 or equivalent , make- skf/ fag/ntn only , single row full complement cylindrical roller bearing , bearing designation/number- skf ncf 3052 cv c3 or fag sl183052 c3 or equivalent , make- skf/fag/ ntn , single row full complement cylindrical roller bearing , bearing designation/number- skf njg 2330 vh c3 or fag sl192330 tb c3 or ntn equivalent , make- skf/fag/ ntn. , single row angular contact ball bearing no.7310 bdb or 7310 b-jp-ua or skf 7310 bmp or equivalent , (steel/brass cage) , make- skf/ntn/fag , tapered roller bearing. bearing designation /number- skf 31310j2/df03 or fag 31310a.k11.a60.100 or equivalent , make- skf/fag/ntn. 1 set of bearings consists of 2 nos. of bearing no.31310a.n11 formerly k11 and 1 nos. of spacer no. a60.100 , for total axial float in assembled condition to be between 60- 100 microns bearing must be purchased as a set only. cage material- steel required for 31-p-

State Government

CTN :43458956

26 Jan, 2026 NA

Ghaziabad - Uttar Pradesh

Tender For supply of point machine and various other items as per boq attached inspection rdso rites consignee. - supply of point machine irs type 220 mm stroke clamp type as per irs s$-24/2002 (amendment 1) or latest.(inspection agency:- rdso), supply of q-series led ecr (universal type i.e.qecx-61), 4f/4b complete with plug board(base plate), connectors, retaining clips etc. and conforming to brs: 941a sts / e / relays / ac lit led signal / 09 - 2002, amdt.-1 or latest and rdso spec.no.irs: s - 34, s- 23 or latest, as applicable. the interlocking code for this unit shall be "abdhk". (inspection by rdso)., contactor unit (qbca1 type), 24 v dc, 2hf / 4b complete with plug board (base plate), connectors, retaining clips etc and conforming to brs- 943 and rdso specn. no. irs : s - 34, s- 23, s - 60 or latest, as applicable. th e interlocking code for this unit shall be "bcejk". (inspection by rdso)., q-series magnetically latched neutral line relay (ql1 type), 11f / 4b, 24v dc complete with plug board (base plate), connectors and retaining clips and con forming to brs-935a and rdso specn. no.irs : s - 34, s - 23 or latest, as applicable. the interlocking code for this unit shall be "abdeg.(inspection by rdso)., supply of basic material to construct unit maintenance free earth as per rdso specs. no. rdso/spn/197 ver. 1.0 or latest to achieve a resistance less than 1 ohm. it consist of following:(a) copper bonded steel electrode of minimum 3.0 meter long, minimum 17.0 mm dia with copper bonding thickness of minimum 250 microns and ul listed and marked = 1 no. (b) earth enhancement material supplied in sealed bags of minimum 10 kg = 3 nos. (c) copper strip of 150x25x6 mm, to terminate earth rod = 1 no. (d) copper strip of 300x25x6 mm (meeb) = 1 no. (e) copper strip of 150x25x6mm (seeb) = 1 no. (ii) supply of 35 sq. mm multi strand single core pvc insulated copper cable as per is: 694 for connecting main earth electrode to meeb in the equipment room in duplicate. (minimum 10 meter.) (iii) supply of 16 sq. mm multi strand single core pvc insulated copper cable as per is: 694 for connecting meeb to seeb and spd to meeb (minimum 10 meter.) (iv) supply of 10 sq. mm multi strand single core pvc insulated copper cable as per is: 694 for connecting various equipments to seeb (v) supply of copper lug sleeve for 3/16 cable.(inspection by consignee)., supply of master telephone with voice logging facility for electronic lc gate telephone system as per specification no: rdso/spn/tc-51/2011 revision 3.0 with amendment no. 1 or latest. (inspection by rites)., electronic lc gate slave telephone system with voice recorder as per rdso specification no. rdso/spn/ tc/51/2021 revision 1.0 (inspection agency:- consignee), supply of centralized power supply system 24 volts dc power pack with 7ah mf battery for electronic lc gate telephone system as per rdso spec:- no. rdso / spn / tc / 51 / 2011 (rev. 3.0) amdt - 1 or latest.(inspection agency:- consignee), supply of optical power meter, type-b, as per tec spec. gr / opm - 01 / 03 feb. 2005 or latest. (make & model khushicom-k280) or similar branded make. (inspection by consignee)., supply and testing of optical laser light source of make- jdsu model- ols-35 or similar branded make.(inspection agency:- rites), supply of optical laser torch of reputed make. (make & model-proskit mt-7530) or similar branded make. (inspection agency: - consignee), supply of automatic fusion splicer for single mode optical fibre cable, along with accessories as per tec spec. tec/gr/tx/osm 001/04/sep-12 or latest of make superior/fujikura or similar. consignee shall approve the supply only after successful demonstration at site. (inspection agency:- rites), supply of otdr suitable for 1310/1550nm fiber with resolution of 60 cm, dynamic range of 314/29 db with all accessories for working on single mode optical fiber as per tec spec. tec/gr/tx/otd 001/05/sep-19 or latest, of reputed make like yokogawa/zdsu/viavi or similar. consi

Central Government/Public Sector

CTN :39971546

10 Jan, 2026 NA

Haridwar - Uttarakhand

Tender For bid to ras supply of seal ring 41350501023 - w96413501650 , scru hex m12 -w97414500063 , seal ring - w96413507080 , washer - w97413900262 , " balancing weight 31360601015, var. 01 - w96413600020 , balancing weight - w96414600024 , balancing strip weight - w96413604492 , balancing strip weight - w96413604506 , balancing strip weight - w96413604514 , " adaptor sleeve (steel) to prod size: 5x12 - w96414300012" , " adaptor sleeve size: 4x16 - w96414300160" , hex socket hd. cap screw - w97413900432 , balancing weight - w96414300195

CTN :43487700

17 Jan, 2026 NA

Bathinda - Punjab

Tender For supply of generator spares d d - electrodes welding steel hard surfacing , plywood general purpose wwr ab 5ply 180c , steel angles 20x20x3mm , bearing set sleeve std size , brg set sleeve 0 25m us , cylinder lines , piston assy standared , set piston ring 0 25mm os , bearing set sleeve std 70mm dia 2 000 1 , transistor 2n5884

CTN :43465633

27 Jan, 2026 NA

Jabalpur - Madhya Pradesh

Tender For supply of n1 1015-000426 packing nut , n1 1015-000772 link , n1 5305-003957 screw fillister head , n1 5306-011895 bolt shoulder , n1 5305-003141 screw set , n1 5365- 001462 spacer plate , n1 5305-003960 screw , n1 ifl- 8613 steel plate jacket 5mm thick 160x200 mm , n1 3040-003055 bell crank , n1 3120-004433 bearing sleeve , n1 1015-000276 pipe coupling air line wheel left , n1 5330-001835 washer felt , n1 4030-001278 rod anchor , n1 5365-010564 ring retaining , n1 5305-003154 screw grub spigot end , n1 5307-004416 stud plain , n1 3040-003626 collar , n1 1015-000404 plate locking , n1 5310-002385 washer felt , n1 iwp- 1192 locating pin , n1 5310-001526 nut assembled washer , n1 5310-002383 washer recessed , n1 3040- 003336 collar shaft , n1 5305-003170 screw shoulder , n1 5310-001559 washer , n1 1015-000341 link locking plunger , n1 5365-010652 spacer ring , n1 5310-002389 nut assembled washer , n1 5340- 015591 hasp hinged , n1 5305-003157 screw set , n1 iwp-1195 angle , n1 6675-000822 scale drawing ) /bid number : gem/2026/b/7075385 * /dated: 06-01-2026 & & / bid document 1 / 27

corporations/Associations/Others

CTN :43247340

10 Jan, 2026 31.00 Lacs

Sonbhadra - Uttar Pradesh

Tender For corrigendum : supply of hot end static seal plate with holding strip , ce static seal plate with holding strip , axial seal plate holding strip with holding strip he , by pass seal plate hot end with holding strip , by pass seal plate c. e. with holding strip , axial seal leaf c. e. with holding strip , t bar he and ce 24 nos. in a set , cold end rotor angle , hot end rotor angle , support grating ce , taper lock bush and adapter sleeve , adjustor bolt of sector plate out board , diaphragm rh cv carbon steel , he radial seal inboard, middle board, outboard with holding strip , ce radial seal inboard, middle board, outboard with holding strip , adjustor bolt of sector plate inboard

Central Government/Public Sector

CTN :43306089

12 Jan, 2026 3.29 Lacs

Wani - Maharashtra

Tender For corrigendum : supply of procurement of spares for roto make pumps d d -stator part no. 8122 , rotor part no. 8125 , coupling rod rm 60 roto part no. rm60rot003 , coupling rod bush part no. mr27 , coupling rod pin part no. mr29 , pump housing for mrsa-081 roto pump part no. 5010 , shaft part no. 8132 , pin cap washer steel rm 60 roto part no. rm60rot002 , seal ring set part no. 8116 , water thrower part no. 8117 , pin retainer sleeve part no. mr50 , bearing housing part no. 8101 , tie rod part no. 8177 , o ring set part no. 81r0 , circlip ring part no. 8185

Central Government/Public Sector

CTN :43452176

20 Jan, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For tender for supply of foc accessories or splicing tools d d -88s+ fiber optic splicing machine , attenuation measurement exfo-max-735d , handheld optical power meter along with standard accessories(olp-35) , handheld optical light source along with standard accessories(ols-35) , fc connector 900um lancer connector with standard boot 500-cfc- s0-n01- 000-1 , patch cords with lancer underwater fc-fc connectors (0.5 mts) (g.657a 900 micron pvc buffer) along with yellow colour sleeve , patch cords with lancer underwater fc-fc connectors (3 mts) yellow colour sleeve , patch cords with lancer underwater fc-lc connectors (0.5 mts) yellow colour sleeve , patch cords with lancer underwater fc-lc connectors (10 cm) yellow colour sleeve , permanent bulkhead single mode (9/125u) fiber optic short feedthrough (1 k psi) for underwater fiber optic fc . connector 500-sfc-s1 b01 -000 , single mode (9/125u) fiber optic adaptor with bulkhead (ik psi) for underwater fiber optic , single mode (9/125u) fiber optic adaptor without bulkhead (lk psi) for underwater fiber optic fc connector (500-afc-ss-n01-000) , fiber optic stripper yellow colored three hole type , fiber optic stripper green color three hole type , single mode portable fiber cleaver , permanent bulkhead single mode (9/125u) fiber optic standard feedthrough (1 k psi) for underwater fiber optic fc connector (500-bfc- 1 -bo 1 -000) , sfp-wdm-sm-0180dia tx l310/rx 1550nm , sfp-wdm-sm-0180dib tx l550/rx 1310nm , sfp-wdm-sm-0160dia tx l310/rx 1550nm , sfp-wdm-sm-0160dib tx l550/rx 1310nm , cleaning solution for connectorisation , inserted steel clear color fusion splice sleeve (1 , 5mm x 40 mm ) , heat shrink sleeve(3 mm) , elvamide 8061 poiimer resin pellets , epoxy 353 nd /4gm/bs eal/prm , kim wipes , texwipe

State Government

CTN :43191712

19 Jan, 2026 50.00 Lacs

Jaipur - Rajasthan

Tender For supply of miscellaneous items for anesthesia department (as per annexure-5) - 01 sga - i gelit should have non-inflatable, gel-like supraglottic airway device for maintaining an open airway, standard 15mm connector, an integrated bite block to prevent airway occlusion, a gastric channel for early regurgitation warning and suctioning, a buccal cavity stabilizer for easier insertion, and an epiglottis rest to prevent obstructionsize:- 1,1.5,2.0,2.5,3.0,4.0,5.0, intubating lma the lma should be sterile, phthalate free, 100 % silicone material, the lma should have a dynamic curve & atraumatic cuff that creates an effective oropharyngeal seal.the lma should have integrated manometer for continuous cuff pressure monitoring, recommend max. intracuff pressure of 60 cm h2o ,allow direct intubation with dual gastric drainage channel , an integrated bite block and must be mr safe , having intubating ability of et tube size ranging from 6.5 to 7.5 mm, dual gastric channel access to manage sudden gastridisection& 10 degree inclination .size:- 3,4,5, combined spinal & epidural set latex free disposable pencil point spinal needle 27g, 127.5 mm with grooved transparent hub with centering protective plastic sleeve, touhy needle with black eye - 18 g (1.3 x 88 mm). protrusion of spinal needle through the back eye of the epidural needle. with epidural catheter, filter, loss of resistance syringe and separate locking device -, epidural full set with catheter having 3 pairs of holes.latex free continuous epidural anesthesia kit containing g18/g16 epidural touhy needle with large crystal clear grooved transparent hub & epidural catheter of g20 /g 19 & length 100 cm. with catheter connector. epidural catheter in the kit is made of 2 layers - inner layer of polyamide & outer layer of polyurethane. epidural catheter has an atraumatic tip design - the catheter has a tapering tip up to 4 cm & 3 pairs of laser drilled holes for distribution of drug. the epidural catheter has graduation markings up to 25 cm & has smudge marking between 11 & 12 cm markings to indicate the position of the catheter tip in the epidural needle & also has a marking at the distal end for catheter connector. the kit also has a small compact ergonomic 0.2 micron epidural filter with pressure resistance of 7 bars. 10 ml loss of resistance syringe with leur slip and parabolic graduation markings., insulated echogenic needle with integrated extension tubing for nerve blocktransparent insulated (teflon coated) needles with depth markings for ultrasound compatibility of these lengths 25 mm (24g), 50mm (22g), 100mm (21g), 150mm (20g). the hub of the needle has an inbuilt cable for connecting to the stimulator & a tubing for injection of the drug by immobile needle technique, all sizes, 20 to 24 gauge with all size (25 to 150mm), pencil point needle (with introducer)pencil point spinal needle with introducer all sizes, agt tracheal tube cuff oral / pre formed south pole tube cuffed oral, 1 eye sizes: i.d. 3.5 9.0 mm semi-seated connector, cupped atraumatic tip, continuous x-ray marker, graduated, low-pressure cuff, blue pilot balloon, valve for luer and luer-lock syringes latex-free sterile ce and usfda approved, agt tracheal tube cuff nasal / pre formed south pole tube cuffed nasal only, 1 eye sizes: i.d. 3.5 8.0 mm semi-seated connector, cupped atraumatic tip, continuous x-ray marker, graduated, low-pressure cuff, blue pilot balloon, valve for luer and luer lock syringes latex-free sterile ce and usfda approved, inj. etomidate 10 ml, inj. sugammadex 2 ml, inj. sugammadex 5 ml, inj. rocuronium 5 ml, pct ( percutaneous tracheostomy tube) with forcefpercutaneous tracheostomy kit with guidewire, dilators, introducer needle, forceps, tracheostomy tube, syringe, scalpel, cannula, : eo (ethylene oxide) sterilizedsuitable for adult and pediatric patients (varies by size)medical-grade polymer and stainless steel (for metallic components)size:- 7.0 , 7

Alloy Steel Tube Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors