Get complete information related to latest Aluminised Coat Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Aluminised Coat Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Aluminised Coat Tenders.
Tender For supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using driving and dr
Tender For supply of corded hand held rotary hammer drill of 500-800watt, input voltage: 220-240 v, , rotation direction: forward and reverse chuck size: 25-30 mm, impact rate: 0-4000 ipm, function: drilling with rotary hammer, drilling capacity in metal: 13-25mm, consists of a motor, gears, and chuck with all parts enclosed in a protective housing with switches and handles for control. [ warranty period: 30 months after the date of delivery ] ]
Tender For supply of cordless brushless hand held drill machine, rotation direction: forward and reverse chuck size:1/2 inch, , function: drilling, drilling capacity in metal: 13 mm, speed - 0-1750 rpm (approx.), lithium ion battery of capacity 12-20 v and 4 ah or better to be supplied with battery and battery charger, consists of a motor, gears, and chuck with all parts enclosed in a protective housing with switches and handles for control [ warranty period: 30 months after the date of delivery ] ]
Tender For corrigendum : supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using
Tender For bid to ras supply of circular stopper plate complete with fittings , clamps emm 230 x 190 mm for use with 150 mm shore , sheet rubber type a grade 1 thickness 3 mm size 1mx1m , pyrotech light stick 8 inch , caulking shipwrights common , nail 63 mm chequred head , battery dry 1 point 5v size large r20 , tape insulating 25mm , engineers screw driver 1 point 6x10x200 mm pr , dc patrol bag , lead sheet 1000 mm x 1000mm x 1 mm thick , commando torch 04 cell , life line , arm badges , battery dry 1 point 5v size medium r14 , battery dry 1 point 5v dry extra small r3 , band multipurpose for 50 mm 100 mm dia pipes , scissors type 2 230 mm scissors 10 , co2 cartridge 60 gm cap , jubilee clip 500 mm , jubilee clip 30mm 50mm 100mm as per is 4762 size type a , plug tapered soft wood 150 mm x 50 mm x 25mm , wedge hard wood 150 x 75 x 25mm , file half round bastard 8 , plug tapered soft wood 300 mm x 150 mm x100 mm , plug tapered soft wood 200 mm x 100 mm x75 mm , pipe wrench , flax canvas variety no 1 , hacksaw blade 12 inch , plug sq tapered soft wood 150 mm x 50 mm x 38 mm , oakum white , wedge soft wood 250 x 90 x 50mm thick , plug sq tapered soft wood 100 mm x 38 mm x 25 mm , plug sq tapered soft wood 150 mm x 75 mm x 50 mm , timber planking tg 75x225x3000 mm , timber shore soft wood him season 150x150x3000mm , wedge soft wood 100x 25x25 mm thick , wedges hard wood 250x150x40mm , flat cold chisel 22x 200 h button head , firmer chisel short plain 50 mm , set of spanners sizes d10 11 d13 14 d16 17 d19 24 , plug sq tapered soft wood 75 mm x 25 mm x 18 mm , wedge soft wood 125x 50x25 mm thick , file 300 mm bastard rough flat width 25 mm with handle , non adjustable flat hacksaw framed 250 is 5169 , double face sledge hammer 1500 is 841 with handle , wedge soft wood 150x 75 x25 mm thick , variable delievery nozzle , antiflash gloves , wooden mallet medium , gloves for fire proximity suit large , aluminisedcoat for fire proximity suit large , aluminised trouser for fire proximity suit large , plug sq tapered soft wood 150x75x50 mm , flat cold chisel 22x200 h button head , nail double point spiked head , double face sledge hammer 1500 is841 with handle , m seal or equivalent , plug tapered soft wood 300m x 150mm x 100 mm , plug sq tapered soft wood 75mmx25mmx18mm , timber planking tg 75x225x3000mm , spanner adjustable 200mm , spanner wheel 305 mm af , engineers screw driver 1point 6x10x200 mm pr , plug tapered soft wood 150mmx50mmx25mm , battery aa alkaline 1 point 5v lr6 , anti-flash hood , battery dry 1 point 5v //bid details 2 / 58
Tender For corrigendum : providing of custom bid for services - schedule i item a labour cost for mechanized cleaning contract at tbm railway station on manpower basis for 1461 days including gst at 18 percent,custom bid for services - schedule i item b service charge or profit at 3 point 85 percent on labour cost for mechanized cleaning contract at tbm railway station on manpower basis for 1461 days including gst at 18 percent,custom bid for services - schedule i item c epf esi bonus cost for mechanized cleaning contract at tbm railway station on manpower basis for 1461 days including gst at 18 percent,custom bid for services - schedule i item d consumable cost for mechanized cleaning contract at tbm railway station on manpower basis for 1461 days including gst at 18 percent,custom bid for services - schedule i item e machineries cost for mechanized cleaning contract at tbm railway station on manpower basis for 1461 days including gst at 18 percent,custom bid for services - schedule i item f protective gears cost for mechanized cleaning con
Tender For auction sale of rolling stock - scrap iron /steel , wood released cut up from one no. condemned 04 wheeler tower wagon no. eru-27, 4 -wheeler mark- ii , ferrous & non ferrous metal scrap with or without wooden attachment to be sold " as is where is basis " lying at location : western railway emu carshed compound at mumbai central (ohe mast location no. 5/2) , reclaimed items to return back by purchaser to custodian are drive /driven wheel-axel set , qty: 01 set (i.e. set of 02 nos. axles attached with 04 nos. steel cast wheels ). custodian : sse/ohe/ m and p mmct . disposable items along with over aged tw eru-27 are : ferrous : 01] ashok leyland diesel engine model no. -6dti complete with fitted attachments without nonferrous items = 01 no. 02] ashok leyland make gear box assly complete with flange and attachments,: 01 unit, 03] clutch system fly wheel , pressure plate, clutch plate, clutch bearing with hub, fork etc., : 01 unit , 04] air brake and reverse forward system complete with air tank 02 nos. and pipe connection and pedal etc, : 01 unit, 05] diesel tank : 01 unit, 06] under frame chassis complete with cattle guard, buffer, screw coupling , brake and clutch arrangement, body upper frame structure. protective screen, center cabin shutters etc. : 01 units , 07] axle drive gears with 04 nos. axle box 04 nos. and wheel bearing, qty: 01 set , 08] laminated bearing spring : 04 nos. , 09] ac panto unit, qty: 01 no. , 10] operating panel complete with electrical accessories head light units, side light, tail light , flasher light, horn, gauges, wiper motor, radiator frame etc. qty: 01 unit,11] screw coupling hook: 01 set, disposable non ferrous items : i) spares fitted in ashok leyland diesel engine model no. 6dti ( i.e. filter housing, timing cover case, tapet cover sump , inlet manifold etc), : 01 set ii) winding of self starter and dynamo, : 01 set, iii) air break valves, reversing valve , nrv and other nipples etc, : 01 set, iv) radiator assly : 01 no. v) aluminum sheet of tw floor sheet , sheet of upper deck , body front side and revolving platform : 01 set, miscellaneous scrap to be disposed of along with tw no. eru 27 are i) lead acid battery 12 v, 180ah, qty: 01 no. without acid, glass of window, floor and front screen, : 01 set, iii) wooden planks of tw body floor, cross members frame, roof planks, upper deck frame, plywood sheet, cabinet roofing felt material ect. : 01 set , [total approx. weight for disposal is 7370 kgs. including ms, wood, nf , battery etc. ] , mode of delivery in number , custodian: sse ohe m and p mmct, to be sale on "as is where is basis " note: 1[ purchasers are requested to see/inspect tower wagon / machinery/site before bidding. no claim will be entertained from purchaser's end after sale. 2] cutting and delivery will be permitted on receipt of full payment only, 3] loading by purchaser,. 4] all delivery dates will be fixed through ireps. purchasers are advised to submit online request through ireps system at least 07 days before for fixation of delivery dates after preparation of delivery order. 5] fdp awarded is 50 days .
Tender For corrigendum : providing of custom bid for services - comprehensive mechanized cleaning and housekeeping of svdk railway station for 03 years/1095 days- manpower wages including epf and esic,custom bid for services - comprehensive mechanized cleaning and housekeeping of svdk railway station for 03 years/1095 days- cost of machinery,custom bid for services - comprehensive mechanized cleaning and housekeeping of svdk railway station for 03 years/1095 days- cost of consumables, tools, protective gears and chemicals,custom bid for services - comprehensive mechanized cleaning and housekeeping of svdk railway station for 03 years/1095 days- cost of garbage disposal,custom bid for services - comprehensive mechanized cleaning and housekeeping of svdk railway station for 03 years/1095 days- contractor profit,custom bid for services - comprehensive mechanized cleaning and housekeeping of svdk railway station for 03 years/1095 days- total value of gst-18%