Tender For dma/hvr/2025-26/water supply materials annual maitainance/ts - electrofusion reducer 90 by 75 mm, pvcbend140mm dia, pvcbend75mm dia, pvcelbows180mm dia, pvcelbows160mm dia, pvcelbows140mm dia, pvcelbows110mm dia, pvcelbows90mm dia, pvcelbows75mm dia, pvcelbows63mm dia, providing and fixing di resilient seated soft sealing sluice valve of variouis dia. with body bonnet of ductile iron di conforming ti is1865 with the latest amendments and of grade ggg 40or50, provision for corresponding dia ms flanges should be made in the estimate.etc. comple for sluice valve of pn 10and 200mm, providing and fixing di resilient seated soft sealing sluice valve of variouis dia. with body bonnet of ductile iron di conforming ti is-1865 with the latest amendments sr rates of valves and provision for corresponding dia ms flanges should be made in the estimate. etc. completfor sluice valve of pn10.0 and 150mm , providing and fixing di resilient seated soft sealing sluice valve of variouis dia. with body bonnet of ductile iron di conforming ti is-1865 with the latest amendments and of grade ggg 40 50, shaft of stainless steel, wedge fully rubber lined with edpm seals of nbr and the valves should be vacum tight and 100complete specification as per item no2.23.2, providing and fixing di resilient seated soft sealing sluice valve of variouis dia. with body bonnet of ductile irondi conforming ti is 1865 with the latest amendments and of grade ggg 40or50, complete specification as per item no 2.23.1, supply, installing,testing and commissioning common control panel consisting of the following incoming no set of phase indicating lamps with sfu of suitable rating no, analog ammeter, no analog voltmeter 1ni with phase selector switch, complete specification as per item no 13.24.1, supply, installing,testing and commissioning common control panel consisting of the following incoming set of phase indicating lamps with sfu of suitable rating , analog ammeter, analog voltmeter 1ni with phase selector switch, complete specification as per item no 13.23, supply of isi mark 175mm nominal bore,plain and steel casing pipe grade of steel fe 410 of wall thickness conforming to is 4270 2001 and latest ammendments, complete specification as per item no 12.32, pvccouplers 200mm dia, pvccouplers 140mm dia, pvccouplers 110mm dia, pvccouplers 75mm dia, pvccouplers 63mm dia, handglovess, pvcreducer 110 mm dia, pvcreducer 90 mm dia, pvcreducer 75 mm dia, pvcreducer 63 mm dia, pvcreducer 50 mm dia, pvcservice saddles 90 mm dia, pvcservice saddles 75 mm dia, pvcservice saddles 63 mm dia, pvcbend 160 mm dia , pvcbend 110 mm dia , pvcbend 90 mm dia , pvcbend 50 mm dia , pvctee 160 mm dia , pvctee 110 mm dia, pvctee 90 mm dia, pvctee 75 mm dia, pvctee 63 mm dia, pvctee 50 mm dia, pvctee 40 mm dia, pvctee 25 mm dia, pvcelbows 200 mm dia, pvcelbows 50 mm dia, pvcelbows 40 mm dia, pvcelbows 32 mm dia, pvcelbows 25 mm dia, pvc flebyible hose pipe 1inch, upvc column pipe 1inch, hdpe pipe grade pe100-pn 10, 63mm , medium duty gi pipe of 25mm dia , medium duty gi pipe of 20mm dia , opvc reducer 200x160 , opvc reducer 160x110 , opvc reducer 110x90 , opvc sliding coupler 200mm pn16 , opvc sliding coupler 160mm pn16 , opvc sliding coupler 110mm pn16 , pvc pipes of 6 kg/cm2 for 90mm(1.313) , opvc sliding coupler 60mm pn16, supply and delivery at site 50mm(2inch) dia heavy duty unplasticized pvc column pipes with heavy duty collars,rubber profile ring,vibration control profile ring,freezing and turbulence free leak proof epdm ring with isi mark with its latest amendments, supply and delivery of galvanized mild steel tubes of 6mtr standard length heavy duty (c class) as per is 1239 (part-i) 1990 with latest amendments with isi mark (one end fitted with heavy duty collar and other end fitted with protective cover)50 mm , supply and laying of lg ut cable having aluminium conductor pvc insulated, sheathed, galvanized steel wire / steel tap armored cable with pvc over sheathing., pvc pipes of 6 kg
Tender For corrigendum : biennial rate contract for online sealing of water, steam, fuel oil leakages in various valves, bonnets, glands and pipe flanges etc. for 4x210 mw and 1x500 mw units at sgtps, mppgcl, birsinghpur
Tender For procurement of koel da rkit 26 and ard 25 - cgsd (mbi), air starter, da sea water pump / assembly of raw water pump, automatic voltage regulator,, dv electronic governor with over speed protection, set of joints, starting air pressure sensor, hp pipe assembly, speed control unit, temp sensor with inbuild transmitter (type-mbt5560,range 0-150d, outpu, limit switch, turbo oil drain pipe, double gear assembly, 0-2.5 bar danfoss make pressure transmitter for marine, pf33 individual pump, fuel pipe (from tank to feed pump tee) (marine-abs approved), set of o ring, exhaust temprature sensor with 2pin connector, fuel leakage switch, pump to leak off (marine abs approved), leakoff pipe (uniflex), piston assembly, fuel pipe (feed pump tee to filter in marine - abs approved), turning gear engaged limit switch, fuel pipe (from fuel filter to fip) (marine abs approved), centrifugal oil cleaner (band design), assly. rocker lever, oil filter element, k-coolant (26 lit can), small end bush (finished), belt v section (bx 58-pitchl ength 1520), hose reducer elbo, set of copper washers, fuel pipe (tee to pump inlet gear end) (marine abs approved), fuel pipe tee to feed pump gear end (marine abs approved), leak off pipe (from hp pipe to collector)marine _x0013_ abs approved, fuel pipe (tee to feed pump) (marine abs approved), belt for sea water pump drive, water level switch, thermostat element, hose for turbo compressor out, breather pipe, breather hose for marine, elbow connection, cly.head steel gasket 1.2 mm, bend 90 for feed pump out, top piston ring, exhaust valve, leakoff pipe for hp jacketed pipe (lh), drain cock, hose (dia 54) (bet.2 pipes), oil control ring, fuel pipe (tee to pump in), nozzle body (for oil spray nozzle), second ring piston, inlet valve, bolt (bearing cap), make up pipe, fuse terminal block 6a with 2a fuse link, exhaust valve seat insert, connecting rod bolt, rc joint, m.b.cross bolt (short), clamp(for fuel pipe), joint for governor mounting plate, special nut for exhaust manifold, valve seal, counter shunk head screw (for dv injector leakoff), valve guides, exhaust manifold stud, grommet: 22 dia ferrule, rubber bush (bottom), joint (bet.exh.manifold and expa. bellow), s.s.nut, sealing cap (for dia 25), valve collet, sealing cap (40 din 443)8, o ring: drain plug, grommet: 12 dia ferrule, stud-m10x1.5x25-8.8, set screw m8x1.25x25...8.8, washer copper, cup for valve springs, gasket (lub oil header), washer copper (18x22), plain machined washer - m6, service kit for heat exchanger, fuel feed pump, service kit for centrifugal filter, k cool super plus 50-50 premix 26 liter can, k-cool super plus, bearing, bearing, k sealent (80 ml), flat seal for oil seal housing, oil seal for drive end, conical copper washer, spring, cup for pr tube, flexible bellow, sea water outlet pipe from cac, joint for t connection, joint for sea water pump, joint for sea water piping, pipe for he raw water out, roller tappet assly, rubber sleeve, set bolt-m14x2x60-8.8, dowel pin, k cool plus 26 ltrs can, clamp (2 pipe), crank pulley, inlet valve seat semi-finish, exhaust valve seat semi- finish, cup washer (for nozzle clamp), valve guide, oil seal pulley end, timing pointer (for pulley), air shut off valve, set of main bearings, set of thrust washer, set of gasket for heat exchanger ts6m, oil pipe ( crankcase to pump), hose for air starter, sub assembly of bearing housing, joint cooler cover(rh)from fwe, k-coolant (26 ltrs can), copper washer (18x22), k-sealant, wire braided pipe from jacketed leakoff to fuel collector, temperature guage (0-120 deg), rubber bush (top), pressure guage (0-4 bar), pipe(sea water pump outlet to check valve), o-ring for drain plug, npt plug with zinc bar with he, k sealant 80 ml, drain cock, stud, set screw -m8x1.25x25-8.8, hose clip, copper washer, anti vibration mount - cori, anabond 666t max 25g, hose t bolt, hose clamp, rotary drain pump, k sealant (80 ml), automatic voltage regulator, worm drive hose clip (70mm), se
Tender For supply of f1 5120-000904 awls garnishing, f1 5120-000637 vices bench 56 mm parrallel clamp type, f1 5120-000648 vices hand 100 mm, f1 5120-000259 cramps carpenters 1800 mm, f1 5120-000093 pliers sealing lead 150 mm, f1 8020-000011 brushes retouching sable no 4, f1 8020-000015 1 brushes retouching sable no 8, f1 8020-000035 brushes paint & varnish flat 20mm, f1 8020-000008 brushes retouching sable no 1, g2 9510-000317 steel bar alloy hot rolled flat 50 x 5mm, g2 9525-000073 wire copper soft for general purposes 1., g2 9505-000065 wire steel mild galvanised 4.00mm, g2 9505-000007 wire steel mild annealed 4mm, g2 3439-000001 electrodes welding bronze 3.15mm, h1(a) 8010-000253 paint r.f.u black matt, h1(a) 8010-007487 paint rfu fin syn enamalled br/spr eau-d, h1(a) 8010-000114 paint r.f.u. prim aluminium water resis, h1(a) 7930-000001 liquid cleaner for automobiles, h1(b) 5350-000005 abrasives cloth emery or corundum size o, h1(b) 9150-000143 soap soft, h1(b) 5350-000017 abrasive paper glass is grit 150 size o, h3 5530-000214 plywood for general purposes bwr-ab 5 pl, h3 5530-000218 ply wood for general purposes bwr-aa 7 p, h3 5530-400124 plywood for general purposes mr-bb 3 ply, h4 8040-000047 tape adhesive w/proof w 40mm x l 65, h9 5640-000005 asbestos mill board 3.2 mm, h9 5330-001897 cork sheet 1.6mm thick