Tender For tender for supply of 26bavc001 spares of atrx and uhf satcom terminal - uhf antenna los , 19 wired rack with shock mounts , lemo connector , control card , rf cable assembly set , led green , led red , display control card , fsu control card , pre controller module , driver amplifier , dual directional coupler 1 , two pole mcb , control card , display card , presure vent , o p cable , dual directional coupler , digital voice card , data control card , gps receiver card , dc dc converter , mother board , display control card , dc pc cables and connectors for 877 ekm submarine , battery 12v 65ah cots item , power supply 0 30v dual channel 10a , through line power meter , attenuator 500w , screw driver kit , attenuator 2kw , atu load test jig , rs232 can interface test jig , rs232 can interface test jig , vswr test jig 3 1 , slt 3003 software loading tool , swd 5000
Tender For corrigendum : supply of chain and chain spares - csm bhogpur, bagasse elevator chain & its spares, chain with case hardened, m.s roller, bush and pins for baggase elevator chain having attachment link at every 4th link., pitch 150 mm, side link as per drg. no.ce/mh/504 with test certificate from approved lab, bush as per drg no. ce/mh/504, roller as per drg no. ce/mh/504, pin as per drg.no ce/mh/504, outer link pin cut type as per drg.no. ce/mh/504, outer link pin size hole as per drg.no. ce/mh/504, inner link bush type (both sides) as per drg.no. ce/mh/504, side attachment link as per drg.no. ce/mh/504, cane carrier chain & its spares, cane carrier chain pitch -150mm complete with pin ,bush and rollers case hardening and assembled with test certificate from approved lab as per drg.no.mh pcc r1, pin as per drawing no. . mh pcc r1, bush as per drawing no. . mh pcc r1, roller as per drawing no. . mh pcc r1, outer link r.h as per drawing no. mh pcc r1, outer link l.h as per drawing no. mh pcc r1, inner link r.h & l.h as per drawing no. mh pcc r1, cane carrier slates as per drg no. mh-517, inter-rack carrier chain& its spares, inter rack carrier chain pitch -229mm complete with pin ,bush and rollers case hardening and assembled with test certificate from approved lab as per drg.no. ce/mh/503, bush as per drg. no. ce/mh/503, pin as per drg no. ce/mh/503, inner link l.h & r.h as per drg.no. ce/mh/503, outer link l.h without attachment as per drg.no. ce/mh/503, side attachment link (outer link l.h) as per drg.no. ce/mh/503, secondary carrier chain & its spares, secondary carrier chain pitch -229mm complete with pin ,bush and rollers case hardening and assembled with test certificate from approved lab as per drg.no. ce/mh/503, bush as per drg. no. ce/mh/503, pin as per drg no. ce/mh/503, inner link l.h & r.h as per drg.no. ce/mh/503, outer link l.h without attachment as per drg.no. ce/mh/503, side attachment link (outer link l.h) as per drg.no. ce/mh/503, csm nawanshahr, supply of secondary carrier chain spares as per drg. no. 183 r3material of side link en 45pin & bush 16ni3cr2/isi57 part 4/1988roller is- 226- 1975hardness = pin 50 5 hrc bush 40 5 hrc roller 30 5 hrcbreaking load = 60 ton, supply of cane carrier chain and spares as per drg. no. 216 r3material of side link 55c8/is 1875:1978pin & bush 16ni3cr2/isi57 part 4/1988roller is- 226- 1975hardness = pin 50 5hrc bush 40 5 hrc roller 30 5 hrcbreaking load = 40 ton, side link (fig no. 1), side link (fig no. 2), side link (fig. no. 3), roller (fig no. 4), pin (fig no. 5), bush (fig no. 6), slats (fig no. m- 316r), supply of rbc chains as per drg. no. m- 263rmaterial of side link 55c8/is 1875:1978pin & bush 16ni3cr2/isi57 part 4/1988roller - is 226-1975hardness = pin 50 + 5 hrc bush 40 + 5 hrc roller 30 + 5 hrcbreaking load = 60 tonsupply of spares for r.b.c. chain as per drg. no. m-263 r1, side link for bush (fig no. 1), side link (round hole) ( fig no. 2), side link (one side cut hole) (fig no. 3), side link for attachment ( fig no. 3 a), attachment no. m 111r2, roller (fig no. 4), bush (fig no. 5), pin (fig no. 6), rake (grill type) as per drg. m-111r3, pin for rake as per drg m-111r4, supply of forged link chain 229 mm pitch as per drg. no. m-305specification:material of forged block - en 30 bmaterial of pin & bush - 16ni3cr2pin hardness - 50 5hrcbush hardness - 40 5hrcbreaking load - 70 ton, csm batala, pin for rbc as per drawing no. bcsm/mh/01, bush for rbc as per drawing no. bcsm/mh/01, roller for rbc as per drawing no. bcsm/mh/01, pin for mbc as per drawing no. bcsm/mh/01, bush for mbc as per drawing no. bcsm/mh/01, roller for mbc as per drawing no. bcsm/mh/01, pin for elevator as per drawing no. bcsm/mh/01, bush for elevator as per drawing no. bcsm/mh/01, roller for elevator as per drawing no. bcsm/mh/01, pin for cane carrier as per drawing no. bcsm/mh/01, bush for cane carrier as per drawing no. bcsm/mh/01, roller for cane carrie
Tender For supply and installation of automobile trainers and equipment at consignee locations. (tender ref no.26008/2026-27) - light motor vehicle driving simulator, injector -multi hole type, pintle type, petrol engine - 2 stroke, motor cycle/ scooter, injector cleaning unit, injector testing set (hand tester), fuel feed pump for diesel, fuel injection pump - diesel - inline, fuel injection pump - dismantling tool kit, fuel injection pump - distributor fuel rotary pump with standard accessories, fuel injection pump - ve pump with standard accessories, cylinder liner- dry & wet liner, cylinder liner - press fit & slide fit, steering assembly - rack and pinion, air brake trainer assembly, alternator assembly - lmv, engine bearing model set, piston model set, front axle assembly, rzeeppa joint with stand for dismantling and assembly, full floating axle and semi floating axle assembly, wiper motor assembly, cut section model - 4 cylinder diesel engine, cut section model - automatic transmission gear box, cut section model - centrifugal clutch assembly, cut section model - diaphragm clutch assembly, cut section model - radiator - cross flow, cut section model - radiator - down flow, cut section model - shock absorbers, cut section model - single plate clutch assembly, cut section model - turbocharger, demonstration board - anti theft device car, automotive safety air bag simulator, car air conditioner trainer, demonstration board - crdi system, demonstration board - electronic ignition system and ignition coil, disk brake trainer, drum brake trainer, working model - power windows, working model - torque converter, denting kit set, engine compression tester (diesel), two post car lift- capacity 4 ton, electric operated, radiator pressure tester, tyre changer machine, tyre air pressure gauge with holding nipple, wheel alignment machince computerized 3d, wheel balancing machine (for wheel balancing of lmv), air conditioning service unit - car, automotive battery charger, automotive battery tester/ analyser, battery terminal cleaner tool, air blow gun, air impact wrench with impact sockets, engineers stethoscope, grease gun - 500 grams, oil can 500 ml, oil filter wrench - upto 500 mm, piston ring compressor - 50 - 100 mm, piston ring expander and remover - 50 - 100 mm, piston ring groove cleaner, belt tensioner gauge, car jet washer with standard accessories, auto electrical work bench, gloves: rubber, gloves: cotton, industrial/ safety shoes, industrial helmet, blow lamp: 0.5 liter, magnifying glass: 75 mm, lifting tackle/ sling: 1 ton, 2 meters, laser distance measuring instrument, demonstration board: electric vehicle cooling system, engine and transmission system for electric vehicle, cut section of electric vehicle motors, hvac trainer, electric vehicle service equipment test adapter kit, battery tester with inbuilt printer, lighting and wiring system for electric vehicle, electric vehicle diagnostic scanner, solar based charging system, electric vehicle tool kit, electrically insulating blanket, clamps for insulating blanket, insulated rubber mats, gloves: electrically insulated, industrial/ safety shoes: electrically insulated, glove inflator kit, goggle: white glass, ac current digital clamp meter, digital continuity tester, soldering iron set: mechanic electric vehicle
Tender For corrigendum : supply of switching impulse board , racks power supply board inco spares , servovalve amplifier , diving servocontrol , cpu board set , cpu board set front and rear servo , i o bus interface board , logic 2 3 board , analog input board current , voltage analogic inputs , 4 x channel rs485 module , logic output module , vme io interface board , serial link mother board , module c633 a ssu , logic input module , current analogic , voltage analogic , ventilation fan rack 19 , cpu board set for normal monitoring , esd kit electrostatic sensitive device kit , interface test equipment including laptop software , current test adapter for echosounder , drs1 simulator tool cs 55 , tool set of adaptor seb5900 , 1 wk12 dummy load tool cs 118 , dummy load for sonar beacon