Latest arm cylinder Tenders | Government arm cylinder Tenders

CTN :45690243

06 Jul, 2026 NA

Panchkula - Haryana

Tender For supply of bearing ball , housing filter , filter , universal joint assy jcb , service kit dozer , elbow on bypass filter , hose oem , arm cylinder seal kit , seal dust master , bulb instrument , hub dust cap dolly , washer spring , spring , element filter , tube fuel supply

CTN :45658093

02 Jul, 2026 NA

Amritsar - Punjab

Tender For supply of calisthenics gym customized , motorised 4 hp bode gym treadmill 150 kg , full body physical therapy chair with zero gravity , cross trainer hydraulic , dumbbells with rack

CTN :45621023

27 Jun, 2026 NA

Madurai - Tamil Nadu

Tender For purchase of lab equipment for mechanical dept and electronics and communication dept - purchase of lab equipment for mechanical department and electronics & communication department specification (detailed in nit - ), mechanical department tail stock assemblymedium-duty tailstock assembly for dismantling & assembly, dc motor, hydraulic cylinder, hydraulic operated directional control valves (dcv, bearing with shaft assembly, coupling unit using driving and driven shafts using plummer block bearing unit, a).sliding mesh gear box for dismantling and assembling (b) constant mesh gear box cut section, electronics and communication department8051 micro controller kit, embedded trainer kit (using lpc2148), single phase induction motor, dth trainer kit, fiber optic communication trainer kit, sim reader trainer kit

CTN :45280788

20 Jun, 2026 NA

Patiala - Punjab

Tender For bid to ras supply of r1 spares for engineer equipments - camshaft, cover, bare, plug temp gauge, bolt hex, bearing bush, banjo bolt, banjo bolt, copper joint banjo bolt, banjo bolt m8x1x21mm long, ring set piston std, pressure gauge, temperature gauge, plier combination 6 inch, torque wrench, air vent screw, rpm hour meter, grease gun push type, starting rope, coupling half clutch side, ring set, gasket cylinder head (1080x od 92, assembly cranckcase with bush, assy cover gear train side, filter fuel assy, flywheel, connecting rod, oil seal b85 x 120 x 12, oil seal b85 x 125 x 12, blade ripper, air filter inner, air filter outer, element lubricating oil filter, seal oil ring, fuel filter cartridge, suction hose hyd pump, flat face coupling set, flat face coupling set, loader lift cylinder pipe rod end rh, loader lift cylinder pipe rod end lh, bty isolator, arm cylinder seal kit, bucket cylinder seal kit, float needle, fuel pipe line, clamp, grease fitting, tubing, ratchet

CTN :45304418

22 Jun, 2026 2.96 Crore

Bharathpur-Rj - Rajasthan

Tender For corrigendum : tender for supply of medical equipment required for setting up ultra burn care centre. - electro surgical unit/diathermy , skin graft mesher, , suction machine (heavy duty), , ot table (general surgery hydraulic (electric), , defibrillator biphasic, , steam sterilizer/autoclave, , burn treatment bathtub, , volumetric infusion pump, , syringe pump, , 15 (3 per bed), , electric dermatome, , multipara monitor, , icu ventilator advanced, , blood gas analyzer (abg), , video laryngoscope, , air mattress anti bedsore, , fully automatic icu beds, , over bed table, , ecg machine 12 channel, , flexible fiberoptie bronchoscope, , resuscitator hand operated adult, , resucitator hand operated pediatric, , crash cart, , instrument trolley, , automated vertical autoclave, , portable xray machine, , anesthesia workstation, , skin graft handle, , combo3 plus (tens+ift+ems+russina), , pulsed electromagnetic field (pemf) therapy, , ultrasonund therapy (1 & 3 mhz), , class iv therapeutic laser, , shockwave therapy (eswt), , air compression units for physiotherapy, ultrasonund therapy (1 & 3 mhz), , class iv therapeutic laser, , shockwave therapy (eswt), , air compression units for physiotherapy, , emg (electromyography biofeedback device), , height adjustable treatment table, , continuous passive motion (cpm), , motorized cpm-shoulder/elbow, , intelligent active-passive trainer (upper limb and lowe limb combined), , common sensorized rehabilitation gloves, , computerised pulley system, , digital gait analyzers, , quadriceps exercise chair, , tilt table (motorized), , shoulder wheel with magnetic resistance, , standard auxiliary crutch, , walkers, , elbow crutch, , wheel chair (detachable armrest & footrest), , hand gym kit, , exercise resistance bands/tubes, , balance board/wobble board, , theraputty & gel balls, , occupational therapy workstation, , foam bolsters & wedges (2 set), , kremer wire splint each set of 50, , contrast bath, , butterfly shape hydrotherapy tank, , hydrocollator (hot pack unit), , cold therapy (chilling unit)

CTN :45448823

20 Jun, 2026 2.99 Lacs

Baramulla - Jammu And Kashmir

Tender For corrigendum : supply of filter oil eng 12 , filter air outer , filter air inner , filter hyd assy , element filter , hose drain , screw , filter fuel assy , hose heater formed , pipe oil , kit seal , kit coupler , seal , bulb , seal kit , hose , bolt , belt drive , washer , belt alternator , light head rh assembly , light head lh assembly , hose hyd , filter air cleaner assy , bulb 37point5w , washer sealing , pum wiper washer , washer spring , hyd oil temp gauge , element filter , seal kit lift arm cylinder , pipe assembly , hose assy , shaft face seal , seal kit bucket cylinder , bolt , hex nut 5 by 8 18 unf 16 , pipe assembly 1 , hose assembly 4 , oil seal 4 , brake seal kit , o ring , suction hose charge pump , motor seal kit vis 30 by40 , hose wp 190 bar , o ring kit , ring back up

CTN :45532259

21 Jun, 2026 NA

Kanchipuram - Tamil Nadu

Tender For supply of mechanical and electrical equipments - supply - mechanical lab equipments, single phase ac circuit kit for voltage, current and power measurement- 5a,300v, 300w/5a measurement of power by using various loads analog voltmeter 0-300v ac panel mountedanalog ammeter 0-5a ac panel mountedanalog wattmeter 1.5kw ac panel mountedsingle phase digital power monitor to measure powersingle phase ac lamp load 230v/5a 1kwpanel enclosure with hylam front panel with input/outputterminal outlets , mcb elcb trainer kit- 1 phase/3 phase, 2/3/4 pole, 3a-16a single pole mcb 2-5ampstwo pole elcb 30malamp load single phase 5amps panel enclosure and terminal outlets, four stroke petrol engine cut section model - single cylinder four stroke petrol engine cut sectional model with carburetor, spark plug, cut cylinder, piston, connecting rod, crank shaft, valve mechanism, cam shaft, timing gears and flywheel. all parts cut opened to study the components and its working provision to take values for valve timing. surface finish: painted and color coded for easy identification of components mounting: heavy-duty ms fabricated stand/base display type: static / dynamic demonstrationmodel, dc motor - type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armaturefeatures: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder - bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply: mounted on training base suitable for dismantling and inspection, bearing with shaft assembly - type: dismantling and assembly teaching unit shaft diameter: 30 mm shaft material: en8 steel bearings: deep groove ball bearing (6205 / 6206) housing: cast iron locking arrangement: circlips lock nuts end coversmounting: bench-mounted / frame-mounted unit, coupling unit using driving and driven shafts using plummer block bearing unit- the plummer block housing material: cast iron (grade fg 200 or equivalent).type: sng or snl series (split-type housing).sealing: felt seals or v-ring seals (to demonstrate lubrication retention).lubrication: provided with a grease nipple at the top center for manual lubrication practice. the bearingtype: self-aligning ball bearing (1200 series) or spherical roller bearing (22200 series).bore diameter: standard 25mm or 30 mm. shafting and coupling shaft material: groundcarbon steel (en8 or en9) for high surface finish. coupling type: flexible coupling: to demonstrate the bearings ability to handle slight misalignment. rigid flange coupling: to demonstrate traditional direct connection. driving/driven setup: one shaft connected to a small electric motor (driving) and the other to a brake drum or load (driven)., (a).sliding mesh gear box for dismantling and assembling - (a) max transmitted power 1to1.5hp, torque capacity- 40 to 200nm, number .of speed 3 to 6, gear module 1.5 to 2, sliding mesh gearbox gearbox type- sliding mesh forward gears- 3reverse -yes gear material -alloy steel lubrication- splash / oil gear teeth- spur typical gear ratios- 3.2:1 / 2.0:1 /1.3:1 input speed- 0 1800 rpm housing material- cast iron(b) constant mesh gear box cut section - constant mesh gearbox (cut section) gearbox type :constant mesh forward gears :4 gear teeth -helical / spur dog clutch type- sliding lubrication -oil sae 80w90 housing- cut section material -hardened alloy steeleducational features-labeled parts., measurement scale: a vertical steel meter scale, usually with (1mm) graduations, for precise deflection measurement., accessories: includes a set of slotted weights (e.g., (6times 50g) or similar sets) for incremental loading.

Central Government/Public Sector

CTN :45484840

24 Jun, 2026 NA

Bangalore - Karnataka

Tender For supply of supply the pneumatic trainer kit , supply of hydraulic trainer kit

Central Government/Public Sector

CTN :45270454

17 Jun, 2026 10.12 Lacs

Jharsuguda - Odisha

Tender For corrigendum : supply of joy stick rh_part no.156pm91293 , joy stick lh_part no.156pm91285 , switch starting_part no.808620000 , toggle switch_part no.155eg82551 , pressure gauge_part no.56184200504 , sensor eng.oil temp_part no.125eg81441 , fuel level sensor_part no.155eg82495 , temp. gauge_part no.155ip81084 , seal kit_part no.155hs00018 , seal kit bucket cylinder_part no.160hc02207 , seal kit arm cylinder_part no.160hc02191 , battery relay_part no.808820000 , battery -ve terminal_part no.cet0402160 , battery terminal positive_part no.cet0401175 , tube for fip_part no.31z7130072 , feed pump assy_part no.31z7102119 , fuel gauge_part no.155ip81068

CTN :45430790

18 Jun, 2026 NA

Ariyalur - Tamil Nadu

Tender For supply of mechanical engineering lab materials - mechanical engineering lab materials, serve motor drive kitinterface l293d motor driver ic with arduino to control direction of rotation of two dc motors), bldc motor kitbldc motor 1 nobldc motor drive -1noinbuilt volt and ammeter and rpm meterinbuilt power supplyinput 230v ac, lvdt trainer kit complete educational trainer for linear variable differential transformer (lvdt) displacement measurement. built-in ac excitation source and signal conditioning circuitry for lvdt operation. micrometer assembly for precise linear movement of the lvdt core. displacement range ~10 mm with clear front-panel adjustments for zero & calibration. digital display (typically 3 -digit) for direct readout of conditioned output/displacement values. test points and banana sockets for signal observation on external instruments. self-contained unit in a durable enclosure with labeled controls and educational layout. includes user manual and patch cords for experiments. operates on 230 v ac, 50 hz mains supply., multi-cylinder petrolphase : single phase load: mechanical load with ropenumber of cylinders : 4displacement : rope brakepower : 65hp,4000 rpm,1396 ccbrand material : mild steelengine type : 4 stroke self startfrequency : 15hzfuel consumption : petrolfuel tank capacity : 5 letermorh s test rig, tail stock assemblyheavy-duty lathe tailstock assembly for training; cast iron body with base, barrel (quill) ~50 75 mm stroke, hand wheel feed, dead centre mt2/mt3, set over screws for taper turning, spindle clamp, complete with all internal parts for dismantling and reassembly; suitable for 300 400 mm centre height training lathe., dc motorvoltage 220-440 v dcpower - 180 w speed - 200 rpm, hydraulic cylinderdouble acting hydraulic cylinder, bore 40 50 mm, stroke 200 300 mm, working pressure up to 100 160 bar, steel tube with honed bore, hard chromed piston rod, front & rear end caps, piston with seals and wear rings. supplied as standalone unit with suitable mounting for dismantling, inspection and reassembly., hydraulic opreated directional control valve (dcv)manually operated 3/2 or 4/2 way spool type hydraulic directional control valve, nominal size ng06 (cetop 3) or equivalent, rated pressure 210 bar, flow 20 40 lpm; valve body with hardened and ground spool, centering springs, ports p a b t clearly marked. supplied on small mounting plate for dismantling, inspection and assembly practice., bearing with shaft assemblyteaching unit with shaft 25 35 mm dia mounted in housing with deep groove ball bearings (6205 / 6206 class) at both ends; includes locking arrangements (circlips, lock nuts, covers). designed for repeated removal, cleaning, lubrication and refitting of bearings, with provision to mount on bench or test rig., coupling unit using driving and driven shaft plumber block bearing unit1. the plummer block housingmaterial: cast iron (grade fg 200 or equivalent). type: sng or snl series (split-type housing).sealing: felt seals or v-ring seals (to demonstrate lubrication retention).lubrication: provided with a grease nipple at the top center for manual lubrication practice.2. the bearingtype: self-aligning ball bearing (1200 series) or spherical roller bearing (22200 series).bore diameter: standard 25mm or 30 mm (ideal for lab scale).mounting: adapter sleeve mounting (h-series) to teach students how to lock a bearing onto a smooth shaft.3. shafting and couplingshaft material: ground carbon steel (en8 or en9) for high surface finish.coupling type: * flexible coupling: to demonstrate the bearings ability to handle slight misalignment.rigid flange coupling: to demonstrate traditional direct connection.driving/driven setup: one shaft connected to a small electric motor (driving) and the other to a brake drum or load (driven)., spring test machine load & displacement sensing load cel * capacity: 0 10 kno accuracy: 1% fs (better if 0.5% fs) displacement sensor * lvdt / digital encodero accur

Arm Cylinder Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government/Public Sector