Latest asphalt plant Tenders | Government asphalt plant Tenders

CTN :45720703

30 Jul, 2026 2.00 Crore

Chhatarpur - Madhya Pradesh

Tender For inviting rates of different items for construction of diffrent type of work as per demand on cm help line or ward parsad or public - supply of handpump material 2026-27, excavation for roadwork in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location with all lifts and lead up to 1000 m as per section-300 of the specifications.item no nvi-3.12, construction of embankment/sub-grade/earthen shoulders with material obtained from other sources, as per provisions of section 305 of the specifications, with approved materials/soil confirming to requirements given in table 301-1 of specifications including all lead and lifts, including cost of watering, compaction by vibratory roller/heavy pneumatic type roller etc. confirming to requirements given in table 301 2 of the specifications complete.item no nvi-3.12, construction of granular sub-base, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method at omc and compacting with vibratory roller of 80-100 kn static weight to achieve the desired density, including all lifts and lead complete in all respect as per section-400 of the specifications.by mix in place method item no nvi -4.1.1.1, construction of dry lean cement concrete sub- base over a prepared sub-grade with coarse and fine aggregate conforming to is: 383, the size of coarse aggregate not exceeding 26.5mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1 of the specifications, cement content not to be less than 150 kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 mpa at 7 days, mixed in a batching plant, transported to site, laid with paver with electronic sensor/mechanical paver, compacting with 8-10 tonnes vibratory roller, finishing and curing and as per section 601 of specifications.item no nvi- 6.1.1, providing and laying cement concrete grade m-20 with 20 mm graded crushed stone aggregate, mixing shall be in mechanical mixer, laying with paver compacting by use of pin, plate / screed vibrators including form work by strong steel girders fixed by spikes, separation membrane 125 micron thick, including cutting of joints @ 4 to 5 m interval and filling it with hot applied bituminous sealant (without dowel bars) (max. thickness 20 cm).item no nvi-6.4, construction of dowel jointed, plain cement concrete pavement in m-30 grade concrete over a prepared sub base with 43 or higher grade cement, coarse and fine aggregate conforming to is:383 maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver with electronic sensor spreading the concrete by shovels, rakes compacted using needle, screed and plate vibrator and finished in a continuous operation including provision of contraction, expansion, and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, placing of dowel bar, tie rod admixtures as approved, curing compound, finishing to lines and grades as per approved drawings as per irc:15 and as per section-602 of the specifications complete excluding cost of steel in dowel bar and tie rod etc.item no nvi-6.2.1, earth work in excavation for foundation, trenches for pipes / cables or drains etc. by mechanical means / manual means (exceeding 30cm in depth.) including ramming of bottom,dressing of sides,disposal of excavated earth including of all lift and lead upto 50m.disposed earth to be levelled and neatly dressed.all kinds of soil item no nii 2.6.1, demolishing cement concrete manually/by mechanical means including disposal of material with in 50 meters lead as per direction of engineer-in-charge.1:3:6 or richer mixitem no nii

Central Government/Public Sector

CTN :45365796

04 Jul, 2026 11.50 Lacs

Jammu - Jammu And Kashmir

Tender For corrigendum : repair resurfacing of certain roads and connected items at bd bari mil stn - m&l preparing black top surfaces by brushing with wire brushes for removing caked mud etc. sweeping with wire brush/brooms and finally fanning the cleaned surface with gunny bags or by mechanical blower to remove all loose dirt etc to black top surfaces, and applying evenly a priming/tack (viscosity grade paving bitumen of grade vg-10) @ 5 kg per 10 sqm to road surface bituminous asphaltic semi dense concrete consolidated thickness 30 mm with stone chippings graded aggregate with 5.5% of binder content by weight of total mix, (viscosity grade paving bitumen of grade vg-30) and 4% stone dust conforming to required specification for filler as per irc-95, 1987 (filler) by weight of mix, prepared in hot mix plant, rolled and compacted to required camber and gradient to uniform smooth surfaces by mechanical paver and rolled with 8 to 10 tone power roller completed all as specified and as directed., m&l for repair to potholes, any depth ,not exceeding 1 sqm each including sweeping free from dust and mud or water, scoring sunken surfaces in roads, path etc, cutting around edges to at least 25mm in depth, making good by filling in screened and graded road metal, watering and well ramming, applying tack coat with (viscosity grade paving bitumen of grade vg-10) @ 10.0 kg per 10 sqm of surface putting in & including premixed bituminous macadam, well rammed and sealed with binder 9.80 kg/sqm, blinded with 0.09 cum of stone chippings, 6.3mm size and again well rammed, rolled and compacted to required camber and gradient to uniform smooth surfaces by mechanical paver and using with 8 to 12 tonne power roller (including supply of premixed macadam, binder and chippings),completed all as specified and as directed., premix bituminous macadam laid / rolled and compacted using 8 to 12 tonne power roller to required gradient and camber, with broken stone graded aggregate with 4% of paving bitumen binder of viscosity grade vg-30 grade by weight of toal mix (consolidated thickness 75mm or less) completed all as specified and as directed., m&l providing and laying at or near ground level factory made kerb stone of m-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required completed all as specified and as directed., m&l for marking lines 2.5 mm thick, dashes arrows etc of any description n. exc 10cm width/girth on road surface using hot applied thermo plastic road marking paint of approved colour confirming to bs-3262-1989 with special applicator machine all as per manufacturere instruction completed all as specified and as directed., supply and fix solar cat eye (green/red) aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency mono rystafie solar panel 2.4v/ 0.3 watt one ni-ed rechargeable battery (1.2v/ 1600ma) consisting of super bright led with 10,000 to 18,000 mcd completed as per manufactures instructions etc completed all as specified and as directed., supply and fixing metal tubular dealineator made out of abs round body fitted with 2 nos 65 mm dia highly reflective reflectors made out of and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in pcc 1:2:4 (150x150x300mm) type b1 complete all as specified and directed, s&f manufacturing, supplying and fixing retro reflective mandatory/ regulatory sign boards of 900 mm diametre with support length of 3750 mm and made up of 2 mm thick aluminium sheet, face to be fu

State Government

CTN :45696572

01 Jul, 2026 NA

Balurghat - West Bengal

Tender For supply of item rate for construction materials for all types of construction works under mgnrega - hire charges of coaltar boiler 900 to 1400 litres, hire charges of concrete mixer 0.25 to 0.40 cum with hopper, hire charges of diesel road roller- 8 to 10 tonne, production cost of concrete by batch mix plant, hire charges of diesel truck-9 tonne, hire charges of sparaying machine including electric charges, hire charges of coaltar sprayer, hire charges of barber green, drying,mixing and asphalt plant, with accessories, capacity 30/45 tonne, pumping charges of concrete including hire charges of pump, piping work & accessories etc., hire charges of derrick monkey rope, hire charges of pump set of capacity 4000 litres/hour, vibrator (needle type 40 mm), machine for rubbing of floors, front end loader capacity 1.00 cum, hire and running charges of tripod and mechanical winch machine complete with power unit and accessories, mastic cooker, hire and running charges of tipper, hire and running charges of loader, hand grinder for mirror polish, hydraulic excavator (3d) with driver and fuel, pin vibrator, surface vibrator, hot bitumen mixer 0.5cum i/c hand cart, hire and running charges of hydraulic piling with power unit etc. including complete accessories and shifting at site, hire and running charges of light crane, hire and running charges of bentonite pump, hire and running charges of vibrating pile driving hammer complete with power unit and accessories, hire and running charges of crane 20 tonne capacity, carriage of concrete by transit mixer, generator 250 kva, paint applicator, mobile crane, tractor with ripper attachment, tractor with trolley, air compressor 250 cm with two leads for pneumatic cutters/hammers, joint cutting machine with 2-3 blades, c.c.batch mix plant, road sweeper, slip form paver with sensor, water tanker 5000 ltr. capacity, concrete joint cutting machine, texturing machine, dozer d-80-a12, motor grade 3.35 meter blade, hydraulic excavator of 1 cum bucker, front end loader 1 cum bucket capacity (incl pol), tipper -5 cum, vibratory roller 8 to 10 tonne, smooth wheeled roller 8 to 10 tonne, tandem road roller, water tanker 5 to 6 kl capacity, air compressor, wet mix plant 60 tph, mechanical broom hydraulic, emulsion pressure distributor @1750 sqm per hour, hot mix plant - 120 tph capacity, hot mix plant 100 tph capacity, paver finisher hydrostatic with sensor control 100 tph, paver finisher mechanical 100 tph, batching and mixing plant @75 cum per hour, concrete paver finisher with 40 hp motor and sensor, generator 250 kva, generator 100 kva/125, truck 5.5 cum/ 10 tonnes, road sweeper (mechamical broom) @ 1250 sqm per hour, drum type hmp of 60-90 tph capacity @ 75 tonne per hour actual output, hire and running charges of drill machine up to 400 mm dia (including cost of mobile oil, disesel consumption in ordinary soil operator), pile integrity testing equipment, excavation of diaphragm wall by mechanical grab, hire charges of tata 407 or equivalent for local shifting, hire charges of diesel truck - 9 tonne (without pol), using cost of ultra voilet radiation tube, compressor, gun, rubber pipes & other accessories - hire charge of plant & machinery i/c necessary fuel, hire charges of suction jeting machine 2200 psi machine i/c pol and operator, hire charges of drill machine upto 30 mm dia, hire charges of sand blasting equipment, hire charges of compressor, welding charges of shear key to existing reinforcement, hire charges of plant and machinery that can inject 350 kg/day, seam bolts and nuts 6 mm dia and 25 mm long, fibre (high impact poly propelene reinforced) cement corrugated sheet 6 mm thick, fibre (high impact poly propelene reinforced) cement close fitting adjustable ridge, fibre (high impact poly propelene reinforced) cement corrugate serrated adjustable ridge, fibre (high impact poly propelene reinforced) cement plain wing adjustable ridge, fibre (high impact poly propelene reinforced) cem

State Government

CTN :45696571

03 Jul, 2026 NA

Birbhum - West Bengal

Tender For fixation of local market rate (lrm) for supplying of materials (construction plantation materials) for mgnrega work under murarai-ii development block - coal (steam), bitumen vg-30, bitumen emulsion, hire charges of diesel road roller- 8 to 10 tonne, diesel oil, stone screening type a (13.2 mm), stone screening type b (11.2mm), coarse sand, stone aggregate(single size): 06 mm nominal size, grade 1 stone metal 63 mm to 45 mm, 1st class picked jhama bricks(traditional), coloured inter locking c.c. paver block, fine sand, silver sand, portland cement, 1st class traditional bricks (kiln burnt), fly ash bricks(traditional), modular fly ash bricks, modular clay bricks, stone aggregate(single size):20 mm nominal size, stone aggregate(single size): 10 mm nominal size, stone aggregate(single size): 40 mm nominal size, precast cement concrete blocks (nominal mix. 1:1.5:3 with 20 mm down coarse aggregate including supplying at site, laying and finishing the top surface with 1:3 cement mortar), medium sand, udaypur marble slab ( for floor, lobby etc) 18 mm thick of size 0.3 sq m to 0.6 sq m, chawk dungri marble slab ( for floor, lobby etc) 18 mm thick of size 0.3 sq m to 0.6 sq m, udaypur marble slab ( for wall/dado) 18 mm thick of size 0.3 sq m to 0.6 sq m, chawk dungri marble slab ( for wall/dado) 18 mm thick of size 0.3 sq m to 0.6 sq m, ceramic glazed tiles ist quality 300 x 300 mm in all shades and designs of white, ivory, grey, fume red brown etc., rectified - ceramic glazed tiles ist quality 300 x 300 mm or more in all shades designs white, ivory, grey, fume red brown etc, vitrified floor tile 60x60 cm, precast chequered cement tiles 22 mm thick dark shade using ordinary cement, water proofing materials, hire charges of concrete mixer 0.25 to 0.40 cum with hopper, vibrator (needle type 40 mm), hire charges of 5 kva generator, hire charges of 3 kva generator, hire charges of monkey set, hire charges for 5 hp with operator,fuel and shifting etc all charges complete, surface vibrator, water tanker 5000 ltr. capacity, r.c.c. pipes np2 class 300 mm dia, r.c.c. pipes np2 class 450 mm dia, rcc pipe 600 mm dia np- 3 spigot, rcc pipe 900 mm dia np - 3 spigot, rcc pipe 1000 mm dia np -3 spigot, rcc pipe 1200 mm dia np - 3 spigot, empty gunny bag, bamboo (8cm-10cm dia) including fixing, nail, sal bullah (7.5cm -10cm dia), eucalyptus bullah (7.5cm -10cm dia), sal bullah (12.5cm -15cm dia), sal bullah (17.5cm -20cm dia), eucalyptus bullah (12.5cm -15cm dia), eucalyptus bullah (17.5cm -20cm dia), sausage wire net, mild steel tubes hot finished seamless type, galvanised steel corrugated sheets, galvanised steel bolts & nuts 6 mm dia and 25 mm long round head with slots, galvanised steel j or l hooks 8 mm dia, g.i limpet washer, bitumen washer, galvanised steel plain sheets, seam bolts and nuts 6 mm dia and 25 mm long, g.i. plain washer for seam bolts, stainless steel bolts /square bar and plates, welding by electric plant, false ceiling (with 4mm thick pearl designer fibre cement board), supplying, fitting & fixing asbestos corrugated sheet(6 mm thick), supplying, fitting & fixing asbestos ridging, supplying, fitting & fixing zn-al alloy steel sheet work in roof, supplying, fitting & fixing aluminium sheet ridging, fitting and fixing glass reinforced polyester translucent fiber glass sheet, fitting and fixing glass reinforced polyester translucent ridging, fitting & fixing circular corrugated aluminium sheet, tor steel rods/hysd bars/tmt bars (sail/tata/rinl) (fe415/fe500/fe500d conforms to is: 1786), tor steel rods/hysd bars/tmt bars(jsw/jspl/shyam/srmb/bmasl/elecrosteel/ssl)(fe415/fe500/fe500d conforms to is: 1786), tor steel rods/hysd bars/tmt bars (other than sail/tata/rinl/jsw/jspl/shyam/srmb/bmasl/elecrosteel/ssl)(fe415/fe500/fe500d conforms to is: 1786), brick aggregate (single size):40 mm nominal size, moorum, loading unloading & stacking lime, moorum, building rubish and similar miscellaneous material, stone a

Central Government And Public Sector

CTN :45696206

06 Jul, 2026 52.70 Lacs

Delhi - Delhi

Tender For providing of building materials and execution of the allied works under the work conservation of well area of lahore gate including rampart at red fort - material and work, u. lime katni (in air tight bags), surkhi (free from silt, dust, organic any other foreign material), river course sand (free from silt, dust, organic any other foreign material), gum babool, gur desi, belgiri, jute/sun, lakhori brick (as per site requirements nominal size & specification), brick jeera 6mm (free from clay, organic material), brick aggregate (free from clay, organic material) 20 to 25 mm nominal size, red sand stone thickness 100mm of required size, copper dowel (as per site requirement), red sand stone required (as per site requirement size), red sand stone 50 mm (as per site required size thick for jalie work), red sand stone 40 mm (as per site required size thick undressed for chajja), copper rod 10 mm (as per site requirement), un slaked lime katni (in air tight bags) fine quality, marble dust powder [kg], batasha [kg], araldite [kg], 6 inch dia ballies (6 ft ) [each], ply 12mm thick [m2] water resistant, mud (clay ) [cum] free from impurities, dry uppley [each], planks 50m thick [m2] (well seasoned), jute rope 1 inch [kg], "dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres leaddismantling old lime plaster", demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge.nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix), demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge., painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 13.62.1 two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture, provision of provising and fixing of galvanised mild steel material xpended material (xpm) jali of 4mm thick silver in clour inluding fixing charges etc complete, "float glass panes 9.7.7.1 4 mm thick glass pane (weight not less than 10kg/sqm)", "providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).9.1.2 sal wood", "providing and fixing factory made single extruded wpc (wood polymer composite) solid plain flush door shutter of required size comprising of virgin polymer of k value 58-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 n (face) & 900 n (edge), minimum compressive strength 50 n/mm2, modulus of elasticity 850 n/mm2 and resistance to spread of flame of class a category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk s.s screws, all as per direction of engineer-in- charge. (note: stainless steel butt hinges and necessary s.s screws shall be paid separately) 30 mm thick 26.87.1", "providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the rcc structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry :

Central Government/Public Sector

CTN :45649630

06 Jul, 2026 NA

Ranchi - Jharkhand

Tender For providing and supplying of ready-mix concrete _m20_ from batching plant to the roof repair/ seepage treatment works at shyamali colony, doranda ranchi

CTN :45444903

02 Jul, 2026 65.00 Lacs

Ludhiana - Punjab

Tender For corrigendum : estimate for lining of peori disty rd 20137-26187 (extension portion) off taking rd 25518/r of raika feeder by concrete lining m-15 concrete mix, mixed in automatic batching and mixing plant, carried to site in transit mixers, laid manually with s - estimate for lining of peori disty rd 20137-26187 (extension portion) off taking at rd 25518/r of raika feeder by concrete lining m-15 concrete mix, mixed in automatic batching and mixing plant, carried to site in transit mixers, laid manually with specified thickness.

State Government

CTN :45397974

24 Jun, 2026 80.77 Lacs

Kota - Rajasthan

Tender For corrigendum : work of name :- remaining work pkg. no. rj-23-10/srf (rr) / np / 2022-23 distt kota - providing, laying and spreading and compacting specified graded crushed stone in sub-base course including premixing the material at omc in mechanical mixer (pug mill), carriage of mixed material, laying in uniform layers with motor grader, f.e. loader, on a prepared surface and compacting with vibratory compactor to achieve the desired density including all material, labour, machinery, lighting barricading and maintenance of driversion complete. (morth specification clause 401). with all lead & lift, fdkuiqjk rfd;k ls punzsly, total, kilometre stone reinforced cement concrete m15grade kilometre stone of standard design as per irc:8-1980, fixing in position including painting and printing etc ordinary kilometer stone (precast), fdkuiqjk rfd;k ls punzsly, e.mkuk ls guksfr;k, total, kilometre stone reinforced cement concrete m15grade kilometre stone of standard design as per irc:8-1980, fixing in position including painting and printing etc hectometer stone (precast), fdkuiqjk rfd;k ls punzsly, e.mkuk ls guksfr;k, total, providing and erecting typical citizens information board as per approved drawing & specification of mord, made of two ms sheet of 1.6 mm thick each of size 900 mm 750 mm stiffened by angle iron 25 mm 25 mm 3 mm all around the plate and plates fixed on frame of 75 mm dia pipe of 12 swg sheet (vertical post 3050 m with angle holdfasts and horizontal member 900 mm) to be joined by 5 mm thick ms plate at 12 places (65 50 mm) duly embedded in cement concrete m-15 grade of block of 600 mm 600 mm 750 mm size below ground level as per enclosed drawings & as directed by engineering - in-charge. all ms will be stove enameled on both side, lettering, figuring and border will be with ready mixed synthetic enamel paint of superior quality in required shade and colour etc. complete in all respect. all sections of framed post and steel tube will be painted with primer and two coat of epoxy paint as per drawing and as per mord specification., fdkuiqjk rfd;k ls punzsly, e.mkuk ls guksfr;k, total, providing and laying reinforced cement concrete pipes np-3 for culverts including jointing ends and fixing collar with cement mortar 1:2. (morth specification : clause 1000/2900). 300 mm dia, fdkuiqjk rfd;k ls punzsly, e.mkuk ls guksfr;k, total, dry lean cement concrete sub - base. construction of dry lean cement concrete 1:3:6 sub-base over a prepared sub-grade with coarse and fine aggregate conforming to is: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blening to be as per table 600-1, cement content not to be less than 200 kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonne vibratory roller, finishing and curing., fdkuiqjk rfd;k ls punzsly, total, providing and laying un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub-base with 43 grade cement, coarse and fine aggregate conforming to is:383, maximum size of coarse aggregate not exceeding 25mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or fix form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures and vacuum processing pump as approved, curing compound, finishing to lines and grades as per drawing as per morth specification : clause no. 602, 112. using cement concrete m-30 pavement grade, fdkuiqjk rfd;k ls punzsly, total, earthwork in excavation for foundation of structure complete with all l

State Government

CTN :45542764

19 Jun, 2026 NA

Balurghat - West Bengal

Tender For supply of item rate for construction materials for all types of construction works under mgnrega - hire charges of coaltar boiler 900 to 1400 litres, hire charges of concrete mixer 0.25 to 0.40 cum with hopper, hire charges of diesel road roller- 8 to 10 tonne, production cost of concrete by batch mix plant, hire charges of diesel truck-9 tonne, hire charges of sparaying machine including electric charges, hire charges of coaltar sprayer, hire charges of barber green, drying,mixing and asphalt plant, with accessories, capacity 30/45 tonne, pumping charges of concrete including hire charges of pump, piping work & accessories etc., hire charges of derrick monkey rope, hire charges of pump set of capacity 4000 litres/hour, vibrator (needle type 40 mm), machine for rubbing of floors, front end loader capacity 1.00 cum, hire and running charges of tripod and mechanical winch machine complete with power unit and accessories, mastic cooker, hire and running charges of tipper, hire and running charges of loader, hand grinder for mirror polish, hydraulic excavator (3d) with driver and fuel, pin vibrator, surface vibrator, hot bitumen mixer 0.5cum i/c hand cart, hire and running charges of hydraulic piling with power unit etc. including complete accessories and shifting at site, hire and running charges of light crane, hire and running charges of bentonite pump, hire and running charges of vibrating pile driving hammer complete with power unit and accessories, hire and running charges of crane 20 tonne capacity, carriage of concrete by transit mixer, generator 250 kva, paint applicator, mobile crane, tractor with ripper attachment, tractor with trolley, air compressor 250 cm with two leads for pneumatic cutters/hammers, joint cutting machine with 2-3 blades, c.c.batch mix plant, road sweeper, slip form paver with sensor, water tanker 5000 ltr. capacity, concrete joint cutting machine, texturing machine, dozer d-80-a12, motor grade 3.35 meter blade, hydraulic excavator of 1 cum bucker, front end loader 1 cum bucket capacity (incl pol), tipper -5 cum, vibratory roller 8 to 10 tonne, smooth wheeled roller 8 to 10 tonne, tandem road roller, water tanker 5 to 6 kl capacity, air compressor, wet mix plant 60 tph, mechanical broom hydraulic, emulsion pressure distributor @1750 sqm per hour, hot mix plant - 120 tph capacity, hot mix plant 100 tph capacity, paver finisher hydrostatic with sensor control 100 tph, paver finisher mechanical 100 tph, batching and mixing plant @75 cum per hour, concrete paver finisher with 40 hp motor and sensor, generator 250 kva, generator 100 kva/125, truck 5.5 cum/ 10 tonnes, road sweeper (mechamical broom) @ 1250 sqm per hour, drum type hmp of 60-90 tph capacity @ 75 tonne per hour actual output, hire and running charges of drill machine up to 400 mm dia (including cost of mobile oil, disesel consumption in ordinary soil operator), pile integrity testing equipment, excavation of diaphragm wall by mechanical grab, hire charges of tata 407 or equivalent for local shifting, hire charges of diesel truck - 9 tonne (without pol), using cost of ultra voilet radiation tube, compressor, gun, rubber pipes & other accessories - hire charge of plant & machinery i/c necessary fuel, hire charges of suction jeting machine 2200 psi machine i/c pol and operator, hire charges of drill machine upto 30 mm dia, hire charges of sand blasting equipment, hire charges of compressor, welding charges of shear key to existing reinforcement, hire charges of plant and machinery that can inject 350 kg/day, seam bolts and nuts 6 mm dia and 25 mm long, fibre (high impact poly propelene reinforced) cement corrugated sheet 6 mm thick, fibre (high impact poly propelene reinforced) cement close fitting adjustable ridge, fibre (high impact poly propelene reinforced) cement corrugate serrated adjustable ridge, fibre (high impact poly propelene reinforced) cement plain wing adjustable ridge, fibre (high impact poly propelene reinforced) cem

State Government

CTN :45462730

20 Jun, 2026 NA

Vadodara - Gujarat

Tender For annual rate of hotmix material for various roads under rajpipla (r&b) division rajpipla (2026-27) - providing and laying premix semi dense bituminous concrete with b.t. aggregate as per morth gradation & using bitumen emulsion rs-1 as per is 8887: for tack coat @2.50 kg./10 sq.m. on bt surface with asphalt grade vg-30 for mixing @ 50.00 kg./m.t. including heating and mixing the aggregate and asphalt by continuous of batch mix plant and hot laid process laying with paver finisher and consolidation with roller as per morth specification to achieve desire density, including cost all materials equipments, tools and plants, oil, kerosene, firewood, labour charges etc. complete using contractor's own machineries batch mix plant and paver finisher etc. complete. plant and paver finisher etc. complete. providing and laying 50 mm thick bituminous macadam with b.t. aggregate as per morth specification and using bitumen emulsion rs-1 as per is 8887: for tack coat @2.50 kg. / 10 sq.m. on bt surface with mechanical sprayer and bulk asphalt vg 30 for mixing @ 34.00 kg./m.t. i.e. 3.40 percentage of total weight of mix including heating and mixing the aggregate and asphalt in continuous of drum mix plant and hot laid process spreading the same by paver finisher and consolidation with roller as per morth specification to achieve desire density, including providing all materials equipments, tools and plants, fire wood, oil, kerosene, labour charges etc. complete using contractor's own machinery drum mix plant and paver finisher etc. complete. providing & laying bituminous grout 37.5 mm thick compacted with asphalt of vg 30grade @ 1.99 percentage by weight of mix for mixing and 2.5 kg/10 sqm. of rapid curing emulsion for tack coat and using b.t. chips of required gradation including cleaning and heating asphalt premix materials by hot mix process in proper gradation and laying with sensor paver finisher and consolidation work as per most specifications including cost of materials labours labour equipment and plant fuel oil complete.... providing and laying 250mm thick wet mix macadam (w.m.m.) in two layers (each layer of 150mm avearge) using machine crushed black trap aggregate of 40 to 50 mm size in the material with water omc in mechanically mix (pug mill) carriage of mix material by contractor's 1.000 own tipper to site of work including laying, spreading and compacting in sub base, base course on well prepared under base of compacting as per most specification to achieve the desired density (mechanically providing & laying bituminous prime coat asphalt @ 7.5 kg / 10 sqm. of slow curing emulsion as per most specifications including cost of materials labours labour equipment etc. complete..... labour charges for spreading hotmix / drum mix material on scattered area of road by manually in regular shape including surface dressing with wire brush and spreading of sand including cost of sand. complete. (for patch work) labour charges for spreading hotmix / drum mix material by paver finisher including heating and spraying tackcoat as per requirement consolidation by static roller and spraying stone dust as directed etc. complete. providing and laying asphalt painting on b.t. surface with bitumen v.g. 30 at rate of 5 kg./10 sq.mt. and spreading stone dust on painting surface at the rate of 0.03 cu.mt. / 10 sq.mt. in selected length of the road including rolling and cost of asphalt. providing. laying built-up spray grout base course intwo layers with bitumen at rate of 15 kg./per 10 sq.m. with 0.50 cu.m. stone aggregate for first layer and 15kg. of bitumen and 0.50 cu.m. of stone aggregate per 10 sq.μ. of roadsurface for second layer and using 0.13cu.m. of key aggregate per 10 sq.m. excluding rolling and consolidation complete. (stone aggregate and bitumen shall be paid separately) surface dressing two coat with bitumen using 18kg.bitumen per 10.0 sq.m. with 0.15 cu.m. of stone chipping 12mm nominal size per 10.0 sq.m. for first coa

Asphalt Plant Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors