Tender For supply of cat. no- 09020213068 coil for ignitor sov (110v ac, 16w) model no: coil - 34-i-110v ac 50hz-37-h , cat. no- 09020213067 coil for atomizing, scavenging, compressor drain, load/unload sov) , (220v ac, 8 , cat. no- 09020214131 swas panel sov with coil: 34-ii-230v-50hz- 25-rc sov model no: 30310-4-2r-b6-s1 , cat. no- 09020214001 seal kit for pneumatic cylinder (for oil burners) model no: ecf 90 , cat. no- 09020214021 seal kit for pneumatic cylinder (for purging corner) model no: ecf - 100e , cat. no- 09020214011 seal kit for pneumatic cylinder (for atomizing and scavenging) , cat. no- 09020214012 seal kit for pneumatic cylinder (for atomizing corner) model no: ecf - 125e , cat. no- 09020214031 seal kit for pneumatic cylinder (seal air damper) model no: ecf 150e , cat. no- 09020214002 seal kit for pneumatic cylinder (oil shut off, recirculation valve and 12 ata l , cat. no- 09020214013 seal kit for pneumatic cylinder (39 ata atomizing valve) model no: ecf 250e , cat. no- 09020214124 repair kit for ahp-9 compressor sov model no: repair kit for 99-30206c-3-2g , cat. no- 09020214125 repair kit for air dryer sov model no: repair kit for 98- 23102v01-25-8g , cat. no- 09020214126 repair kit for swas panel sov model no: repair kit for 99-30310-4-2r-b5- s1 , cat. no- 09020214127 air dryer drain sov with coil (220v ac) model no: 22101v01-25-8g-b13+ i-220v-ac- , cat. no- 09020214301 3/2 direct acting solenoid valve with coil 240v ac for compressor load/unload s , cat. no- 09020214128 ahp-9 compressor sov model no: 34-ii-230v- 50hz-25-rc , cat. no- 09020214115 sov with coil 220v ac, 50 hz for cross over valve model no: 57404-16-4g+ i- 230v , cat. no- 09020214129 sov with coil 220v ac, 50 hz for bottom ash system model no: 51432-16-4g+ i-230v , cat. no- 09020214003 sov with coil model no: 30318-5-2r-b5+ iii-230v-ac/dc-37-fr-h , cat. no- 09020214130 bf gas line actuator sov with coil: 220v ac, 50hz model no: 31119-16- 4g+ i-230v- , cat. no- 09020214032 sov with coil for ball mill outlet gate model no: 57440a-6-2g+ i-230v-50hz-22
Tender For supply of repair kit for auto drain valve to emd pt. no.40029185, specn. no. mp.0.01.0026 rev. 00 march 2010. [ warranty period: 30 months after the date of delivery ]
Tender For corrigendum : tender for supply of wick long tab , valve plug , o ring ohaulingkithp pumpseal retainer , front , anode plug , hp pump seal kit , oil filler cap , oil seal crankshaft , plunger rod pin , v-packing case , hp pump female adapter , hp pump male adapter , valve spring retainer , valve plug 70 kg , hp pump anode plugs , seal kit , valve set , oil seal crankshaft , connecting rod assebly , plunger rod , plunger rod pin , oil seal crank case , seal retainer - 2 pc , barrier slinger , hp pump inlet manifold , adaptor h.p.pump , male adaptor , v packing spacer , spacer with coil springs , valve plug 70kg , o ring overhauling kit , crankcase casing , straight connector 3-8 , permeate male elbow , cartridge filter element , nozzleset for filter consist of filterhead tube strainer , frp filter type 1354 , nozzle set for frp filter 1354 , nozzle set for sand filter , head distributor , media for sand filter grade-i , support gravel 1.5-3.0 mm , support gravel 2.0-3.0 mm , dolomite , membrane cleaner 22 , membrane cleaner 33 , membrane solution 44 , h.p pump c case oil , jubilee clips 00 13 mm to 20 mm , s.s jubilee clips 1x 30 mm to 40 mm , ss jubilee clips 2x 45 mm to 60 mm , high pressure manifold 3 x 2 arrangement , high pressure manifold 6 x1 , module bypass nozzle , support bracket , pure water manifold , pu9 hose , tie rod nut high , h p connection feed/brine , lip seal dt module , membrane cushion , blue hydraulic disc , o ring for head distributor assembly , o ring hp connection , o ring hydraulic disc , o ring distance fitting inside , o ring distance fitting outside , o ring tie rod screwing inside , o ring crank case cover , o-ring pos. no. 412 for speck pump npy 2051 , high pressure hose module outlet , hp flexible hose , h.p hose feed inlet-brine outlet , brine r/w h.p. flexible hose , brine r/w hp flexible hose-xl , brine raw water high pressure , rubber hose from c-f outlet to hp pump inlet 20-30tpd , lp hose for prefilter pump , hose for pk-20 pump in-out , product water flex hose-fm manifold to plant , lp hose brine - permeate , end conn hoses brine/permeate , rubber hose 20mm , lp hose for air line , av mount akcc 85m , mounts for plant , a/v mount for hp pump trolly , h.p pump driving belt set of 2 , coupler for victaulic coupling 1 , victaulic couplers 1.1-4 , belt spanner , pulsation damper , jubilee clip 40mm , membrane solution 44 , pressure switch , belt hp pump driving , hp pump anode plugs , contractor , o-ring for deacidification filter , o-ring for cartridge filter , kit wear parts , sleeve gasket , neck ring p 45 , neck ring retainer , motor for 30tpd filter prefilter pump , mechanical seal p 105 , sleeve gasket p 37 , corrugated spring p 60 , spacing pipe - 66.a , bearing ring p 47a , spacing pipe -p 64.c , slotted nut p 67 , coupling complete for pump 202699 p 8 , stay bolt for pump p 26 , chamber complete p 4 , neck ring p 45 , neck ring retainer , pump shaft complete for pump 202699 p 51 , chamber with bearing ring p 4a , impeller , spacing pipe - p 64.a , wear part kit - repair kit , split pin , ball bearing , p 154 , shaft pin p-10 , top guide vane p 50a , spacing pipe p 64 , chamber stack for pump 202699 p 80 , chamber , crn 1- 4 pump spindle , crn 1- 4 pump shaft seal p-105 , o-ring 137.5 od x 3.3 thk , shaft pin 50d x 26l , o-ring 16.3od x 2.4 thk 100 , neck ring , neck ring retainer , impeller 30.6id x 73 od x 9h , shaft seal , chamber with bearing ring , neck ring retainer , chamber with bearing ring) , shaftseal p105 , kit , gaskets , cm 3-5 pump 415v 3ph 50hz.ip55 , cm 3-5 sleeve p-16 , cm 3-5 impeller p-49 , chamber , seal ring , filter pump permeate pump , filter permeate pump casing , ring-circlips p-931 , filter permeate pump grub screw , o ring , shaft seal , casing p-1 , reverse vane impeller , p-2b , shaft p-6 , cover for mech seal , sleeve shaft p-14 , i b bearing p-16 , o.b. bearing p-18a , circlip internal p-18b , oil drain plug
Tender For bid to ras tender for supply of cable 3250 mm , engine cranking lever , flexible delivery tube type-98 , hand lamp insp lamp , electric horn 24v dc , filter insert , hose radiator outlet , repair kit valve , water strip door , rotating light , gasket thermostat , plug for oil drain , regulator vehicle window , brass nozzle 40mm with male coupling , door lock front rh , pressure protection valve , ball bearing , material tube repair hot seal patch , grease gun , nut m8 , pad , lock side window lh , wedge , nut
Tender For bid to ras providing of custom bid for services - various repair jobs of emd - overhauling/dismantling of the existing w ater drainer by isolating the drainer by putting blank plate after isolation valve. purging/removal of trapped gas from the seal pot/pipe line by injecting st eam/nit rogen. revisioning of all parts & cleaning of pot. if required, the complete seal pot w ith pipe line has to be new ly fabricated & erected as per the instruction of o.a. or as per draw ing. after erection, testing of pot by injecting st eam/nit rogen and de-isolation/commissioning. the condensate pipe from w ater drainers has to be laid to the nearest storm w ater manhole or as directed by o.a.s representative. painting of w ater drainer and pipes to be done after the erection job , "technical cleaning of gas pipeline water drainers. the w ork involves closing/blanking of valves, st eam purging of pipe/drain pot and opening of f langes of seal pot and removal of muck/deposit from pots, revisioning of gas inspection valve,w ater filling valves,condensate valves. fixing of new packing and tightening of f langes. filling of w ater in the seal pot and de-blanking of w ater drainer/opening of valves. checking for any leakages and rectification of the same " , the job involves cutting/dismantling of corroded structures like column, platforms, w alkw ays, staircases etc. at height. before cutting of any structure, the nearby pipe lines or any other equipment to be supported f irst. the dismantled structures should not be throw n from height. all the dismantled structure to be kept at one place as directed by o.a.s representative for disposal by bsp , the job involves fabrication of st eel structures like column, platforms, w alkw ays, staircases etc. by type 1 electrode, as per approved draw ing / specification or as directed by oa/oa¿s representative complete in all respect including painting. fabricated structures w ill have to be erected by the contractor at height as per the direction of operating authority , the job involves w elding of tack w elded pipes, gland compensators, disc compensators, flanges, st eel structures, gas pipeline equipment, plates, pipes, structures w ith type 1 w elding electrodes , dismantling of gas pipe line or any other pipe line by cutting, including handling and stacking, cutting into pieces and sections as directed by oa/oa¿s representative & stacking at designated location. before cutting the nearby pipe lines/platforms/equipment to be supported. all dismantled structural items to be kept at a particular place, as show n by o.a.s representative for disposal by bsp , job involves erection of fabricated/available pipes at locations show n by o.a./o. a' s representative, including dia. 100mm at heights. erection job involves, lifting of standard length of pipes supplied by bsp free of cost, w elding w ith the existing pipes/valve f langes and testing of pipe w ith st eam/nit rogen and defect rectification w ith type i electrode. any accessories like bleeder pipe, drainer pipe, purging nipples, valves,compensators, saddle supports etc. also to be erected, as directed by o.a , fabricated/available pipes at locations show n by o.a./o.a. s representative, above dia. 100mm and up to dia. 200mm at heights. erection job involves, lifting of standard length of pipes supplied by bsp free of cost, w elding w ith the existing pipes/valve f langes and testing of pipe w ith st eam/nit rogen and defect rectification w ith type i electrode. , fabricated/available pipes at locations show n by o.a./o.a. s representative, above dia. 200mm and up to dia. 500mm at heights. erection job involves, lifting of standard length of pipes supplied by bsp free of cost, w elding w ith the existing pipes/valve f langes and testing of pipe w ith st eam/nit rogen and defect rectification w ith type i electrode. any accessories like bleeder pipe, drainer pipe, purging nipples, valves, compensators, saddle supports etc.also to be erected, a
Tender For supply of repair kit for auto drain valve to emd part no 40029185 dlw part no 17380273 rdso specn no. mp.0.01.00.26 rev 02 june 2024 [ warranty period: 30 months after the date of delivery ]