Latest bar round Tenders | Government bar round Tenders

CTN :45720703

30 Jul, 2026 2.00 Crore

Chhatarpur - Madhya Pradesh

Tender For inviting rates of different items for construction of diffrent type of work as per demand on cm help line or ward parsad or public - supply of handpump material 2026-27, excavation for roadwork in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location with all lifts and lead up to 1000 m as per section-300 of the specifications.item no nvi-3.12, construction of embankment/sub-grade/earthen shoulders with material obtained from other sources, as per provisions of section 305 of the specifications, with approved materials/soil confirming to requirements given in table 301-1 of specifications including all lead and lifts, including cost of watering, compaction by vibratory roller/heavy pneumatic type roller etc. confirming to requirements given in table 301 2 of the specifications complete.item no nvi-3.12, construction of granular sub-base, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method at omc and compacting with vibratory roller of 80-100 kn static weight to achieve the desired density, including all lifts and lead complete in all respect as per section-400 of the specifications.by mix in place method item no nvi -4.1.1.1, construction of dry lean cement concrete sub- base over a prepared sub-grade with coarse and fine aggregate conforming to is: 383, the size of coarse aggregate not exceeding 26.5mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1 of the specifications, cement content not to be less than 150 kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 mpa at 7 days, mixed in a batching plant, transported to site, laid with paver with electronic sensor/mechanical paver, compacting with 8-10 tonnes vibratory roller, finishing and curing and as per section 601 of specifications.item no nvi- 6.1.1, providing and laying cement concrete grade m-20 with 20 mm graded crushed stone aggregate, mixing shall be in mechanical mixer, laying with paver compacting by use of pin, plate / screed vibrators including form work by strong steel girders fixed by spikes, separation membrane 125 micron thick, including cutting of joints @ 4 to 5 m interval and filling it with hot applied bituminous sealant (without dowel bars) (max. thickness 20 cm).item no nvi-6.4, construction of dowel jointed, plain cement concrete pavement in m-30 grade concrete over a prepared sub base with 43 or higher grade cement, coarse and fine aggregate conforming to is:383 maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver with electronic sensor spreading the concrete by shovels, rakes compacted using needle, screed and plate vibrator and finished in a continuous operation including provision of contraction, expansion, and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, placing of dowel bar, tie rod admixtures as approved, curing compound, finishing to lines and grades as per approved drawings as per irc:15 and as per section-602 of the specifications complete excluding cost of steel in dowel bar and tie rod etc.item no nvi-6.2.1, earth work in excavation for foundation, trenches for pipes / cables or drains etc. by mechanical means / manual means (exceeding 30cm in depth.) including ramming of bottom,dressing of sides,disposal of excavated earth including of all lift and lead upto 50m.disposed earth to be levelled and neatly dressed.all kinds of soil item no nii 2.6.1, demolishing cement concrete manually/by mechanical means including disposal of material with in 50 meters lead as per direction of engineer-in-charge.1:3:6 or richer mixitem no nii

CTN :45688894

16 Jul, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For supply of supply of precleaner for air cleaner , connection , o ring for moatti lub oil filter , injector nozzle assembly , zinc rod , 1/8 bsp drain cock , plate covering , valve grinding paste (901702) , joint , lub.oil pressure sensor with switch , set bolt - m12x1.75x50 - 8.8 , set bolt-m16x2x50 - 8.8 , set screw m10x1.5x35-8.8 , stud , socket head grub screw - m10x10 , slotted c sunk head screw -m6x , circlip , banjo bolt-m14x1.5 , washer spring , clip jubilee for strainer , connection piece to turbocharger , flexible hose , temp.indicator 0 50 degc. , glass fuse 300ma size 5x20 fast blow , set of 10 , fuse 1a , iso1 electrodistributor , 24vdc , solenoid return , fuse 2a , fuse 6a , se card , m.e bearings scanner exhaust gas temp , on release safety card rgm card , logic unit and , programmable output(0-20) , indicating lamp-red , with lens , holder and lamp , indicating lamp-white with lens , holder and lamp , fuse cartridge 4a(am)10x38 , watershed connection , plunger barrel assembly (dia 25 mod) , o ring 4 x22.5 perbunan , o ring , o ring (for liner collar) , temp.switch(model ti-250-s)95deg 10m capilla , pressure transmitter , pr. transmitter 0-10 bar , gfl bolts , low lub oil sump level switch , set bolt -m20x2.5x120-8.8 , set scrw -m20x2.5x40-8.8 , stud m12x1.75x45-8.8 , self locking nut , allen screw , screw , socket head cap screw-m12x25-12.9 , socket head cap screw -12x40-12.9 , socket head cap screw-m12x55-12.9 , circlip , circlip external -60mm , banjo bolt - m22x1.5 , washer copper , copper washer , copper washer(33x39) , mech dir pin , spring dowel pin , spring dowel , lock washer pair , plain bearing with bearing bush , thrust ring , locating ring , ring nut , intermediate ring , sealing disc , contact no , pressure gauge 0-4bar dial 4 bourden ss3 , analog indicator 72x72.0-4bar i p4-20m , pressure transmitter , range 0-6bar , pressure switch , set at2.0b , pf-3p4-w-bb-1x00-21b-10b-db-n-v.t , solenoid valve nc 24vdc(y94 , y97 , y142.y143 , y) , high signal selector (or module) , solenoid valve no.24 vdc (y198) , safety stop , pressure guage with glycerine , i/p-0-10 bar , pressure transmitter 0-4 bar 24vdc o/p-4-20 ma , pressure transmitter 10 bar 24vdc o/p-4-20 ma , pressure guage with glycerine , i/p-0-6 bar , selector plate (opening 1 , 3 , 5) , pressure transmitter 6 bar 24vdc o/p-4-20 ma , pneumatic distributor (7/1 , 7/2 , 7/3) fuel rack , pressure transmitter 40 bar 24v dc , pneumatic distributor (8/1 , 8/2 , 8/3 , 8/4) stop , pressure regulator (5) , on/off switch , 2 pole , off delay timer 0.2-300sec.+socket , converter module(t452 , t458)charging airtemp.f.w.temp.(0-100) , supply card , ae 24/24 , sleeve nt-hh-pn10-dn100 , damper key , spring pack(new) , o ring 8.2x680.6 (nitrile) , o ring , o ring , bush(32307) , bush(32301) , signal isolator 4-20 ma/4-20ma loop powered , bearing temp measure card (mtp card) , bearing temp alarm card (aip card) , regr. safeties temp. card (rsp card) , on release safety icm1 card , frequency divider for governor speed sensor , a.b.b t/c magnetic speed sen , solenoid valve cnomo dia-1.6 , 24 vdc , regulator for fw temp. , 24vdc , i/p-rtd , o/p-4-20 ma , green head for push button , blue head for push button , on delay relay 24v dc , threshold module , rgm card , frequency divider-turbo speed , cable (engine speed measure) , pneumatic switch for local/remote operation , selector plate (solid) , selector seal , sub base seal , pilot push in type , fresh water air cooler inlet connection , fresh water pre heating inlet connection , fuel rack indicator , pressure gauge 0-6 bars , pr. switch 1.2bar min. , pr. switch , 4140-c-k-1-e-22-aa0 , 4.1b , pr switch type 4140c-19 bar , pressure transmitter p5r-6bar-4-20-1/2-pe , pressure transmitter p5r 0-40 bar , mss module 0-150 deg(convertor) , temp switch tcm96p 40deg c decreasing , temp switch tcm96r 90deg c increasing , temp switch tcm96r 95deg c increasing , pressure transducer 0-10 bars , mss module 0-100deg.c 4-20 temp con

CTN :45689632

06 Jul, 2026 NA

Nashik - Maharashtra

Tender For titanium bar round 20mm dia

Central Government/Public Sector

CTN :45637861

02 Jul, 2026 NA

Ratlam - Madhya Pradesh

Tender For auction sale of others - released, condemned and u/s miscellaneous ms scrap consisting, {angle, rail pieces, gi pipes off size, gi sheet, iron board (angle+gi sheet) scrap of old broken water tank, channel sec, fencing, tie bar, covershed, steel bar, tmt bar, round bar, beams, flate, height gauge, flush tank, h/pump body, c.i. pipes off size, door, fencing wire}, total qty- 35.00 mt, location- sse-works-nmh office, sse-works-nmh outside office & pump room back side. mode of delivery by actual weighment basis and on as is where is basis, custodian- sse-works-nmh, fdp-50 days. note- cutting is permitted for easy loading only not into small pieces.

Central Government/Public Sector

CTN :45637869

24 Jun, 2026 NA

Multi City - Gujarat

Tender For auction sale of depot ferrous scrap - scrap m s tmt bar,round bar,tie bar fecing,angles etc with or without other attchment old uesd and u.s.( confiscated lot no 2105070326 sold on 12/05/26)

CTN :45624706

13 Jul, 2026 NA

Baitul - Madhya Pradesh

Tender For raw materials office stationary - package 1 hardware items, m.s.round bar 65 mm, m.s.round bar 55mm, m.s.round bar 45 mm, m.s.round bar 40mm, m.s.round bar 35 mm, hss tool bit 1/2 x6 inch, hss tool bit 3/8x6 inch, hss tool bit 1/4x6 inch, power saw blade, hacksaw blade (miranda), cotton waste, oil 90 num, oil 40 number, cutting oil, emery cloth 200 grit, grease, diesel filter, oil filter, air filter, power steering oil, emery paper 36 grit, sulphuric acid (h2so4), soldering paste, ms flat 50x10 mm, ms flat 50x5mm, ms flat 65x10 mm, ms flat 70x10 mm, ms flat 75x10 mm, ms flat 100x10 mm, ms flat 50x12 mm, hexa blade (pack of 100), round bar 10mm ms,, gi sheet 0.5 mm, dowel pin, emery paper 80 grit, counter sunk head screw, round head slotted screw, drill bit 3mm, drill bit 4mm, drill bit 6mm, drill bit 8mm, drill bit 10 mm, drill bit 12 mm, punch, pan head revit, ms angle 25x25x3 mm, ms angle 40x40x5 mm, ms strip 20x2 mm, ms pipe 50x3 mm, copper pipe 1/2 inch, welding electrode 2.5 e6013, welding electrode 3.15 e6013, welding electrode 4mm e6013, oil paint, soft wood 4x4x5, soft wood 3x3x5, soft wood 2x1x5, soft wood 1x1x5, fevicol, nails 1, nails 2, nails 3, screw1, screw 2, screw 3, oil stone, wood polis titli, touch wood, plywood 8mm (4feet x6feet), plywood 12mm (4feet x6feet), plywood 18mm (4feet x6feet), emary pepar 80 no, emary pepar 100 no, emary pepar 120 no, grinding disk, grinding disk, cotton tape, pili mitti powder, wooden putty, polyfix wood sealer, paint, distilled water, oil paper sheet, steel wire brush, multipurpose cleaning brush, brush, cleaning solvent, benton grease, battery clamp, hydrolic fluid, package 2 electrical, battery, soldering iron, soldering wire, soldering flux, resistance 1 ohms, resistance 10 ohms, resistance 1k ohms, resistance 10 k ohms, resistance 100k ohms, inductor 4.7uh, inductor 10uh, inductor 5uh, inductor 6uh, inductor 8uh, inductor 330uh, capacitor 3f, capacitor 3.3f, capacitor 5f, capacitor 6f, capacitor 5uf, capacitor 6uf, capacitor 8uf, leds 2v, leds 2v, leds 2v, leds 2v, leds 2v, push buttons, ic 741, ic 555,, mcb,ic7806, mcb, ic7905, switch two way, 5 pin shocket wall mounting type, wall mount batten-holder, bakelite angular-holder, fan regulator mounting type, hrc fuse -, 12 mm no.5 wood screws, 20 mm no.6 wood screws, 25 mm no.6 wood screws, neon lamp switch bord, machine screw, saddles, tube light choke, tube light rod, tube light holder plain, h.p.mv lamp holder suitable for, h.p.mv lamp choke -, capacitor, lead acid battery, pvc copper wire 1mm (90meter), pvc copper wire 1.5 mm (90meter), pvc copper wire 2.5mm (90meter), crimping spade 6a, crimping spade 16a, mccb, elcb, rccb, helogen lamp incandescent lamp, high pressure mercury vapor lamp, l.p.m.v lamp, high pressure sodium lamp, low- pressure sodium lamp led, helmat electrician yellow color, screw driver kit set, toggle switch,, resistors, carbon composition 62k , 1/4 w, 5%, resistors, carbon composition 33k 1/4 w, 5%, resistors, carbon composition 22k 1/4 w, 5%, resistors, carbon composition 220 1/2 w, 5%, resistors, carbon composition 330 1/2 w, 5%, resistors, carbon composition 470 1/2 w, 5%, resistor 10 ohms 5w, resistor 1k ohms 2w, resistor 330k ohms 2w, resistor 2 ohms 5 w, resistor 50 ohms 5w, potentiometer 500 ohms, 0.5a, potentrometer 100 k ohm, resistor 22 ohms 1 w, pvc saddles, led, intermediate switch, tap roll electrician, diode in4007, step-down transformer, variable resistor, dry cell, zener diode,, buzzer, conduit pipe metal iron, bare copper wire, multistrand cable 14/0.2 mm (90meter), multistrand cable 23/0.2 mm (90meter), multistrand cable 48/0.2 mm (90meter), incandascent lamp, pvc cable 3 core, pvc single stranded copper cable 1/1.4 ,1.5 mm, pvc single strand aluminium cable 1/1.8 , 2.5 sq mm, cotton tap, binding steel gi wire, lead and tin alloy, impregnated cotton tap, bitumen compound, lug board, double pole switch, lamp holder bayonet cap batten, barrater resistor, 4 way terminal pad, miniature l

CTN :45602721

09 Jul, 2026 NA

Chandigarh - Chandigarh

Tender For supply of aluminium bar round 30mm

State Government

CTN :45397974

24 Jun, 2026 80.77 Lacs

Kota - Rajasthan

Tender For corrigendum : work of name :- remaining work pkg. no. rj-23-10/srf (rr) / np / 2022-23 distt kota - providing, laying and spreading and compacting specified graded crushed stone in sub-base course including premixing the material at omc in mechanical mixer (pug mill), carriage of mixed material, laying in uniform layers with motor grader, f.e. loader, on a prepared surface and compacting with vibratory compactor to achieve the desired density including all material, labour, machinery, lighting barricading and maintenance of driversion complete. (morth specification clause 401). with all lead & lift, fdkuiqjk rfd;k ls punzsly, total, kilometre stone reinforced cement concrete m15grade kilometre stone of standard design as per irc:8-1980, fixing in position including painting and printing etc ordinary kilometer stone (precast), fdkuiqjk rfd;k ls punzsly, e.mkuk ls guksfr;k, total, kilometre stone reinforced cement concrete m15grade kilometre stone of standard design as per irc:8-1980, fixing in position including painting and printing etc hectometer stone (precast), fdkuiqjk rfd;k ls punzsly, e.mkuk ls guksfr;k, total, providing and erecting typical citizens information board as per approved drawing & specification of mord, made of two ms sheet of 1.6 mm thick each of size 900 mm 750 mm stiffened by angle iron 25 mm 25 mm 3 mm all around the plate and plates fixed on frame of 75 mm dia pipe of 12 swg sheet (vertical post 3050 m with angle holdfasts and horizontal member 900 mm) to be joined by 5 mm thick ms plate at 12 places (65 50 mm) duly embedded in cement concrete m-15 grade of block of 600 mm 600 mm 750 mm size below ground level as per enclosed drawings & as directed by engineering - in-charge. all ms will be stove enameled on both side, lettering, figuring and border will be with ready mixed synthetic enamel paint of superior quality in required shade and colour etc. complete in all respect. all sections of framed post and steel tube will be painted with primer and two coat of epoxy paint as per drawing and as per mord specification., fdkuiqjk rfd;k ls punzsly, e.mkuk ls guksfr;k, total, providing and laying reinforced cement concrete pipes np-3 for culverts including jointing ends and fixing collar with cement mortar 1:2. (morth specification : clause 1000/2900). 300 mm dia, fdkuiqjk rfd;k ls punzsly, e.mkuk ls guksfr;k, total, dry lean cement concrete sub - base. construction of dry lean cement concrete 1:3:6 sub-base over a prepared sub-grade with coarse and fine aggregate conforming to is: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blening to be as per table 600-1, cement content not to be less than 200 kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonne vibratory roller, finishing and curing., fdkuiqjk rfd;k ls punzsly, total, providing and laying un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub-base with 43 grade cement, coarse and fine aggregate conforming to is:383, maximum size of coarse aggregate not exceeding 25mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or fix form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures and vacuum processing pump as approved, curing compound, finishing to lines and grades as per drawing as per morth specification : clause no. 602, 112. using cement concrete m-30 pavement grade, fdkuiqjk rfd;k ls punzsly, total, earthwork in excavation for foundation of structure complete with all l

CTN :45587245

27 Jun, 2026 NA

Nashik - Maharashtra

Tender For supply of aluminium bar round 100mm dia,steel bar round 60mm dia,ptfe bar round 35mm dia

corporations/Associations/Others

CTN :45525616

17 Jun, 2026 NA

Mumbai - Maharashtra

Tender For to supply deck consumables - pencil roller brush (paint roller mini )100nm, with handle, polka dotted hand gloves (long sleeve) knitted type, stainless steel rule, 12, nylon belt sling, 100mmx3mtr,swl 2ton with tc, bucket, plastic, with handle, 10 ltrs, bucket plastic, with handle, 20 1.trs, mug, plastic, capa -1.5/2 ltrs, wall clock quartz, hatch tarpaulin pvc with eyelet 4x4 mtr, padlock, 40 mm, with 3 keys, brass, hacksaw blade high speed steel i" (miranca), anti chemical goggle, anti splashing, floor wiper with long handle, 400mm, ducting tape, size 2 ^ n * 25 long, butt hinge for cabin door, 3", butt hinge for cabin door, 4", 1/2 inch fresh water tap (steel), latch for ship cabin door size: 2 ^ n * x * q ^ n, rubber solution, speb 7., loctite 495, chipping goggle plastic, standard, aa battery 15 v, aaa battery 1.5 v, ear plugs plastic, scrapperl shaped double ended, steel, 12", long handle scrapper, single piece rain coat with hood rubber xl size, gum boots full size with lining inside: size 47, gum boots full size with lining inside: size:, gum boots full size with lining inside: size, gum boots full size with lining inside: size 0, electro cleaner spray, kilnit, p.p. rope 3 strand, 220 mtr 6 mm dia, pp rope, 3 strnd, 220 mtrs, 12mm dia, p.p. rope, 8 strand, 220 mtrs, 64 mm dia, 7.92 in, mbl 47500 kgf, floatin, type with manufacturers certificate., yacht mop complete, length overall 1580 mm, nylon deck brush with handle 12", door mat nylon lawn step 45x75 cm, door mat coir size 1.5" x 14" x 24, door mat coir size 1.5 x 24" x 36", brush, deck, 12", nylon, without handle, dustpan plastic, sponge mop with handle, width 180mm., examination pad, shower mixing valve (hot/cold), faucet wall combination 1/2" with hose pipe, plastic shower curtain size: 100mm x 1900mm, rubber hand gloves 14" (ordinary), slotted v-gard safety helmet, yellow, slotted v-gard safety helmet, white, buffing wheel id 19 mm and od 160 mm, thickenss-20 mm, water finding paste [100 grms], air hose 19mm x 30 mtr long (double layer), sounding tape 30 m (heavy bob) m.s, measuring tape, steel, 5 mtr len, measuring tape, steel, 15 mtr len, shower head dia-12 mm, monoblock mixer, for wash basin, manila rope 3 strand 3 strand, 22 mm x 220 mir length,, self drilling screw 1", self drilling screw 2", cargo net 3 mtr x 3 mtr, mesh size: 200mm, mesh rim rope 24mm, screw driver, engineer pattern, 10mm x 400 им, allen key (set of 9 pcs in mm), camlock coupling male/female, 3", brass, chipping hammer, butterfly nuts with eye bolt m12 x 70mm, butterfly nuts with eye bolt m16 x 100mm, rubber packing (hatch/wt door), size: 36mmxi8mm, bolt & nut, ss, ht, od 3 mm, l: 50 mm, cabin door rubber packing 25mm x 5mm the self sticking), towel bar round double 610mm, emery paper sheet grit coarse 230x280 mm, emery paper sheet grit medium 230x280 mm, hp toner cartridge 88 a hp for laserjet p1007, white chalk, cotton rags good quality banian material

Bar Round Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government/Public Sector

State Government

corporations/Associations/Others