Get complete information related to latest Bearing Pad Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Bearing Pad Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Bearing Pad Tenders.
Tender For supply of assy cylinder block , assy cylinder head , gasket engine over hall , piston std , set of piston ring std , set of thrust washer , set of main bearing , con rod bearing , con rod bush , srdg ball bearing , locking plate , key-8x13 crank , cam shaft bush , propeller key camshaft , valve tappet in ex gaed , push rod inlet and exhaust , lock retainer valve spting , valve spring lock half , valve spring washer , gasket for support inj pump , rubber tube 140 injector , hose reducer for leak off inj , head water separator spin on , hose clamp , element air cleaner primary , element air cleaner softy , valve inlet and exhaust , valve oil seal , thermostat plastic assy , thermostat hose pipe with clamp , speedo meter sensor f14 wheel , banjo washer 10,12,14,17,19 , clutch sleeve cylinder assy. , clutch master cylinder assy. , diesel filter , oil filter body with filter , wiper motor reserve tank , timing cover oil seal front , crank shaft rear oil seal rear , diesel rubber pipe , jumble clip big medium , oil pipe rubber , rubber pipe hose , cam shaft tikki , oil jet , clutch plate assy , locking wire release brg , back light assy. rh ) /bid number: gem/2025/b/6949870 * /dated: 01-12-2025 & & / bid document1 / 38
Tender For procurement of spares for aph (model 27.5vitm 2000 72 degree pa) of 2x250mw unit no.10 and 11 of stps sarni. - spares for air preheater ( model 27.5 vitm 2000 720 pa ) of 2x250mw units., inboard & outboard static seals for hot end sector plates; (one set = requirement for 1 aph),, inboard & outboard static seals for cold end sector plates; (one set = requirement for 1 aph),, cold end grating (one set = requirement for 1 aph),, t-bar including t - bar pin, t- bar tab and t- bar clip for hot end, taper lock bush of o/p shaft of main drive gear box, kao wool packing, packing rope for air sealing cover assembly (guide bearing), packing rope for air sealing cover assembly (support bearing), 50 mm gun metal valve thread connection for los working pressure 5 kg/cm2, 25 mm gun metal valve thread connection for los working pressure 5 kg/cm2, rotor angle he (one set = requirement for 1 aph),, soot blower pipe along with nozzle assembly, filter for air motor 1" bsp, relief valve(die casting)22 mm for lube oil system, working pressure 5 ksc, one end is56mm & other end is 46 mm, make-corona or equivalent., lubricator for air motor 1" bsp, wash pipe assembly for hot end & cold end with ss nozzle(one set consist of 02 nos. ), steel wire rope preform, ungalvanised steel wire rope core iwrc/steel core as per is 2266/2002, tensile strenght-1770 n/mm2, length:70 meter, dia. of rope- 6 mm, construction 6x19, make-usha martin or equivalent., by pass seal bar assembly (one set consist of 1 hot end by pass seal bar -03 nos., 2 cold end by pass seal bar-03 nos.), hot intermediate end support grating plates, shoot blower warm gear box, air motor model no ir92ra014,5.51:1 make: ingersol rand or equivalent, pin rack assembly, guide bearing air seal assembly (consist of followings aluminium seal assembly (upper) -01 no. aluminum seal assembly (lower) -01 no. spring -06 nos. bolt-06 nos. nut-06 nos. locknut-06 nos. washer-18 nos. pin-02 nos. seal ring retainer-01 no., hot end sector plates including static seals on both side (along with fasteners) and tracking arrangements for inboard and outboard side for aph.one set consist of 03 nos sector plate i.e.a) sector plate fg to sab) sector plate fg to pac) sector plate sa to pa
Tender For supply of thrust bearingpad{ with spare dimension} (hw- 020.02) -- item as per drg. 31170301040 rev. 08 with ma , thrust bearingpad{ with spare dimension} (hw-020.01) -- item as per drg. 31170301030 rev. 08 with ma , thrust bearingpad{ with spare dimension} (hw-020.03) -- item as per drg. 31170301050 rev. 08 with , thrust bearingpad{ with spare dimension} (hw-020.04) -- item as per drg. 31170301090 rev. 08 with ma
Tender For supply of spares for wilo mather and platt v.t. pump of berhampur water supply system - the list of pump fittings for vt pump model-vmp-21a, sl. no. 81280333/80 of wilo-mather & platt make., thrust block with moc of en8 (part no 2883), spherical roller thrust bearing with moc of std (part 2604), key for thrust block with moc of ss 410 (part no 3280), oil level indicator with moc of std (part no 4700), thrust bearing housing with moc of cast iron (part no 2882), cooling coil with moc of copper (part no 2732), water thrower with moc of nitrile rubber (part no 2070), impeller with moc of cf8m (part no 1500), suction bell mouth with moc of cast iron (part no 4910), suction strainer with moc of ss 304 (part no 4900), o ring( st. box) with moc of nitrile rubber (part no 4250-5), o ring for rm pipe with moc of nitrile rubber (part no 4250-2), o ring( bottom pipe ) with moc of nitrile rubber (part no 4250-1), bearing cover with ratchet with moc of ca15 (part no 2880), oil retainer bush with moc of m.s. (part no 2810), gasket (for bearing housing) with moc of champion af 120 (part no 4080), rising pipe (intermediate) with intermediate bearing bush carrier with moc of m.s & c.i. (part no 1151,2820)