Tender For supply of liner cylinder std , seal o ring liner , bush cam shaft , bearing crank shaft 0 10 , bearing connecting rod 0 20 , piston with pin with lock , piston ring std , thrust washer upper std , thrust washer lower std , bush connecting rod u b , rod and cap assy connecting rod with bolt and nut , pin dowel block , engine overhauling gasket set complete , valve air intake , valve exhaust , seal valve stem , valve seat , valve guide , seal oil crank shaft rear , seal o ring spacer , seal oil crank shaft front , bolt fan , bearing fly wheel , belt drive fan belt , filter assembly secondary for turbo charger , filter assy engine oil , tap and screen assy fuel fuel tank , disc clutch pto , disc clutch main , kit fuel filter primary and secondary , gasket oil sump , gasket fip ear inspection plate , gasket water pump , gasket crank shaft rear oil seal , gasket timing gear housing , gasket timing gear cover , gasket cylinder head , gasket cylinder head cover , gasket air intake manifold , filter assy hydraulic lift oil intake , seal o ring hydraulic , clamp radiator upper , seal o ring , seal benjo washer , u j cross propeller shaft , yoke propeller shaft , bush pin swivel housing upper front axle , bearing sp herical lower , pin swivel housing upper wing pin post , seal o ring front axle , seal oil half axle shaft 4wd front axle , seal wheel housing 4wd front axle , tie rod end , cylinder assy power steering pipe inner and outer , clamp assy house , gasket water outlet , ring thermostat sealing , gasket exhaust manifold , hose assy fuel filter to fip pump , hose assy fuel feed pump to fuel filter , gasket hydraulic pump , hydraulic oil filter , gasket turbo charger oil outlet , pipe metal power steering to inter oil , pipe metal hydraulic pump , jubilee clip half inch , benjo washer copper all size , benjo bolt 19 no , benjo bolt 17 no , bolt and nut 10 no , bolt and nut 12 no , bolt and nut 14 no , valve grinding stick , seal oil gear box , gasket egr valve , injector fuel return pipe rubber , gasket fuel tank , gasket turbo charger to adopter , stopper cable , temperature sending unit , oil pressure sending unit , front indicator sparking light assy , back light assy , insulation tape , 0 to 20 no size writing brush short hair , 0 to 20 no size writing brush long hair //bid details 2 / 64
Tender For set of 160 kn air spring assembly for fiat type bogie as per rdso str no. rdso/2020/cg-01.scope of supply shall be as per clause 4.1 of rdso str no. rdso/2020/cg-01. each set will consist of four air spring assembly. following items shall be supplied as persl.no. 12 of annexure viii of rdso str no. rdso/2020/cg-01 as loose and packedseparatelyper air spring assembly - (a) high tensil hexagonal socket head cap screw - 4 nos; (b) hardened and tempered washer - 4 nos ; (c) prevailing torque type hexagonal nut m20 - 4 nos. the following additional spares also are to be supplied and packed separately per coachest. (i) sealing o- rings - 2 nos; (ii) high tensile hexagonal socket head cap screw ? 4 nos; (iii) hardened and tempered washer - 4 nos. (iv) prevailing torque type hexagonal nut m20 4nos. [ warranty period: 30 months after the date of delivery ] ]
Tender For hand pump spares parts isi mark and conforming to is 15500 2021 (part 1 to 8) (with up to date amendment) - prevailing torque type steel hexagonal nutm10x1.5 is:7002, ball bearing 20 bc02pp is:6455, bolts for cover m 12x20 is:1363, washer for axle to suit m-12 is:2062, high tensile bolt m-10x40mm is:1364 part-i, hexagonal bolt m12x1.75x40 is:1363 part-i, hexagonal nut m12x1.75 is:1364 part-3, hexagonal coupler m12x1.75x50 is:15500 part-4, long bolt m12x1.75x20 for extra deep well is:1363 part-i, reducer cap painted for mark ii & extra deep well hand pump i.s.i. mark - 0.880 kgs approx., cylinder body with brass liner for deep well pump isi mark. - 2.50kgs approx., cylinder body with brass liner for extra deep well and vlom pump isi mark. - 3.20 kgs approx., plunger yoke body for all types of pumps i.s.i. mark. -0.260 kgs approx., spacer for nitrile rubber pump bucket for all types of pumps i.s.i. mark.-0.210kgsapprox., follower for mark-ii deep well i.s.i.mark.- 0.280kgs approx., follower for extra deep pump i.s.i.mark.- 0.370kgs approx., check valve seat for mark ii & extra deep well i.s.i. mark.- 0.210 kgs approx., check valve for mark ii & extra deep well i.s.i. mark, rubber seat retainer for mark ii & extra deep well 0.080 kgs approx., lowerspacerforextradeepi.s.i.mark.-0.200kgs approx., chain with coupling for all types of pumps i.s.i. mark.-0.550kgsapprox., front cover hot dip galvanized for all types of pumps i.s.i. mark.-1.230 kgs approx., bearing spacer for axle for all types of pumps i.s.i. mark, third plate galvanized for all types of pump i.s.i. mark. -1.400kgs approx., connecting rod for all types of pumps i.s.i.mark.-2.7kgsapprox., washer electro - galvanized i.s.i. mark, stand galvanized normal isi mark ii & vlom i.s.i. mark.-17.900 kgs approx., stand galvanized telescopic for marks & vlom i.s.i. mark.-19.750 kgs approx., stand galvanized normal for extra deep well i.s.i. mark.-18.700 kgs approx., stand galvanized telescopic for extra deep well i.s.i.mark.-20.500kgsapprox., handle comprising handle bar, bearing housing & chain guide for mark ii & vlom i.s.i. mark, handle comprising handle bar, bearing housing & chain guide for extra deep i.s.i. mark, t bar for extra deep well i.s.i. mark, counter weight for extra deep i.s.i. mark. -12.00 kgs approx., water tank complete for mark ii deep well & extra deep well hand pump i.s.i. mark. - 7.80 kgs approx., head complete for mark ii & vlom i.s.i. mark.-10.220 kgs approx., head complete for extra deep well i.s.i. mark.-10.150 kgs approx., s.s. handle axle for all types of pumps i.s.i. mark.-0.350 kgs approx., s.splungerrodformarkiii.s.i.mark.-0.430kgs approx., s.s. plunger rod for vlom & extra deep well i.s.i. mark.- 0.470 kgs approx., rubber seating for upper valve for all types of pumps i.s.i. mark, pump bucket of nitrile rubber for all types of pumps i.s.i. mark, rubber seating for lower valve for mark ii & extra deep i.s.i. mark, sealing ring for mark-ii & extra deep well i.s.i. mark, head assembly complete with handle assembly, for mark ii & vlom isi mark., head assembly complete with handle assembly for extra deep isi mark, handle assembly complete for mark ii deep well & vlom pumps isi mark.-10.250 kgs approx., handle assembly complete for extra deep well hand pump isi mark. -15.350kgsapprox., cylinder assembly complete for mark ii deep well hand pumps isi mark.-6.10kgs approx., cylinder assembly complete for extra deep hand pump isi mark.-7.00kgsapprox., plunger valve assembly suitable for nitrile bucket comprising of plunger yoke body, upper valve, spacer follower pump bucket & upper value seating for mark ii deep well hand pump consisting of isi mark spares., plunger valve assembly suitable for nitrile bucket comprising of plunger yoke body, upper valve both spacers, follower pump bucket & upper value seating for extra deep well hand pump consisting of isi mark spares., check valve assemb