Get complete information related to latest Bracket Holder Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Bracket Holder Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Bracket Holder Tenders.
Tender For supply of installation of additional godrej workstations - worktop , panel 24 mm width 23mm , panel 48mm width 53mm single side , 2way 180 , 52mm leg , 23mm leg , single side leg 490 length , 2way fin post with cap 48 inch left hand , 2way fin post with cap 48 inch right hand , top trim , workstation bracket , holderbracket left hand , holderbracket right hand , fabric half screen , panel 48w 53mm double side , double side leg , 3way fin post with cap 48 inch , pedestal 390w x 435d x 646 height , 3drawer 2box and 1file , keyboard tray with mousetray metal , cpu trolley with castors
Tender For tender for supply of wr-3.4 220-330 ghz waveguide based gsg rf probe of pitch 50um micro meter with bias tee optional and becu tips for gold or copper mmic pads , wr-3.4 220-330 ghz waveguide based gsg rf probe of pitch 100 um micro meter with bias tee optional and becu tips for gold or copper mmic pads , wr-3.4 220-330 ghz waveguide based gsg rf probe of pitch 75 um micro meter with bias tee optional and becu tips for gold or copper mmic pads , calibration substrate for gsg probes with pitch between 40-150 um micro meter calibration file should be available up-to j-band , dc-67 ghz gsg rf probe of pitch 150 um micro meter with becu tips for gold or copper mmic pads and female 1.85 mm connector option.
Tender For supply of wr-06(110-170 ghz) waveguide based gsg rf probe of pitch 50um (micro meter) with bias tee (optional) , wr- 06(110-170 ghz) waveguide based gsg rf probe of pitch 100um (micro meter) with bias tee (optional , calibration substrate for gsg probes with pitch between 40-150 um (micro meter) (recommended upper f , calibration substrate for gsg probes with pitch between 75-250 um (micro meter) (recommended upper f
Tender For custom bid for services - defect rectification of acsr 2 (south tower)-defect., in has reported that tracks are not available on display of acsr #2., defect identification., di for the same was undertaken on 13 jun 2025. it was found that the pedestal unit, was required to be replaced to rectify the defect., scope of work to undertake defect rectification., 1. spare part., the required pedestal unit for replacement will be provisioned by in on site. all other, components/ units of acsr #2 should be in place to operationalize the system., 2. manpower., three skilled technicians will be required to undertake the pedestal replacement work., one tower climber also needs to be available on site. the tower climber and two, technicians will be provisioned by hela., 3. material/ machinery., one overhead crane with a loading capacity of one ton lifting to a height of 35 mtrs is, required to undertake the work. the same will be provisioned by in., 4. tools and accessory., the following are required and will be provisioned by hela:-, (a) torque wrench, (b) level indicator, (c) eye hook -02, (d) two 50 mtrs rope, (e) silicon, (f) drill machine, (g) lubricant, (h) slings for lifting, 5. activity to be undertaken., the sequence of events for replacement of pedestal unit will be as tollows:-, (a) disconnect and remove all cables, wave guide ard units from the antennae assembly., (b) fitment of lifting eye hook on antenna and pass lifting slings to the eye hook. dismantle antenna from pedestal unit and keep it on even surface on, the ground with the help of overhead crane. special care is o be undertaken while handling waveguide., (c) hook on the pedestal unit on overhead crane and op an securing bolts, of pedestal unit. lift the pedestal and move to the ground with cap closed of all connectors., (d) hook up new pedestal and lift it to the tower top and w hen aligned with, the position of pedestal plate lower the pedestal on the plate and tight the nut, bolt with level indicator on top of the pedestal to confirm tht the same is at, zero level., (e) lift the antenna to the top of tower and fix it to the pede stal unit., (f) install all units of acsr on top of tower and fix connectors and waveguide to the antenna., (g) switch on power and carry out power checks and fo (hecks., (h) switch on the acsr server and carry out alignment of system to get the tracks appeared on the display., 6. safety., all man working on tower should wear safety belt, safety helmet and safety belt to be, tied on two rigid point at tower top. the man below tower for handlin activity should, wear helmet. the antennae assembly and pedestal unit should be se cured with twopoint safety rope while lifting and lowering the same to avoid any dan age to the man, and material view heavy wind, lifting jerk or swing of the crane sling., .
Tender For procurement of spares for il-78 aircraft - built in test unit (kurs mp-70), control panel kurs mp 70, tacan control unit, atc mode s transponder, tcas unit version of software, unit(v), unit, unit - eletrical braking system (v), tcas control panel, rectifier b 502(kurs mp-70), antenna gps kln 90b, elect mechanism, temperature regulator, lamp hinged, ubs multi purpose common unit, cylinder - door, middle, isolation vavle, pressure regulator, csd regulator, unit kp2 8zh, unit kp2 8ye, unit kp2-47(waveguide switching unit), switching unit, control unit, cut out unit, relay unit, pressure switch, input output device, antenna, pump, signal limiter, power supply unit, bulb-temperature(v), air starter
Tender For industrial safety face shield attached with safety helmet with detailed specifications as per annexure-i attached. a. the safety helmet should be as per is 2925:1984 (reaffirmed in 1995) with hdpe shell material, ratchet type head band, air vent holes, nylon chin strap, electrical/heat/water resis tant certification, max. weight up-to 300gms, with shelf life of 5 years & warranty period of 12 months. b. the safety face shield with minimum thickness of 2mm & should be as per is 8521:1977(reaffirmed in 2007) part 1 (type 3 class1). face shield should have polypropylene bracketholder, polycarbonate viso r & minimum warranty period of 12 months.(the detailed specifications are attached in annexure-i) material to be procured from oem or its authorized deale r/distributer only. one sample to be approved first before bulk supply. the lab test reports must be obtained from nabl approved lab only. lab test certific ate must be provided during supply of sample & warranty certificate must be provided during supply of material. [ warranty period: 30 months after the d ate of delivery ]