Tender For supply of 5 watt vhf set batteries for make motorola xir p6600i (li ion 7.4 volts/2450mah) or similar as per rdso specification no. rdso/spn/tc/ 107/ 2018 ver 2.1 or latest. the battery should wor k for at least 10 hours in l0:10:80 duty cycle modes (10% in tx mode, 10% in rx mode and 80% in idle mod e). the li-ion power pack shall be fixed to the walkie-talkie sets by means of suitable locking arrangement. the set should have 'battery low%u201f alert in the form of audio alert or visual indication or both when ba ttery reaches a certain minimum level ( for example 20%) for early warning to the user. battery should be o f radio oem recommended and bis approved. the ip rating of battery should be same as of 5w radio set. warranty period: 12 month(s) from the date of supply. [ warranty period: 30 months after the date of del ivery ]
Tender For supply of kenwood walkie talkie battery charger of model ksc-43 or similar for charging 2,5 50mah/7.4v high capacity li-ion battery pack as per specification no. rdso /spn/tc/107/2018 ver (2.1) or latest. quick battery charger may consist of adapter and charging tray as separate units or both may be int egrated as a single unit, it should be radio oem recommended and bis approved. in case of separate units , it should be radio oem recommended and adaptor of the battery charger shall be bis approved. battery c harger should give dc voltage as required for charging the battery of vhf set from input voltage of 230 +- 10%, 50 hz. the charging time should be 2 to 4 hours for charging batteries up-to 3000mah in case battery is fully discharged. the charger should have visual indications to indicate the power on/off, battery chargi ng under progress and fully charged condition of the battery. radio oem recommended certificate and bis certificate to be submitted along with the tender. [ warranty period: 30 months after the date of delivery ]
Tender For supply of probing device/measuring tools set consist of: a) rmp 60(q) radio/radi, part no: a-5742-0 001 -- 02 nos b) bt 50 shank omp60/rmp, part no: m2045-0073-- 01 no required make : renisha [ wa rranty period: 12 months after the date of delivery ]
Tender For flash sterilizer, ultrasonic bone scalpel system for spine surgery/ osteotmy, lymphedma, arthroscopic radio frequency ablator with shaver system and inflow outflow pump, general orthopaedic instrument set
Tender For bid to ras tender for supply of purchase of spares c c = - stop (plate no- b2-1-4 , sl no-29) , spring extension (plate xxv a) , buffer , mounting rear road light l oblique s(plate viii h) , knob excavator c oblique w switch as supplied(d1-8-35) , rubber hose(plate-l1-4-10) , door stay , plate door catch , sealing ring ce(ms-190) , relay f by r (ms sl-140) , brush spring(ms-191) , lock cover door lh (plate iv n) , pad wear 6mm upper colour red , lower door glass(ms sl-46) , pad wear 7mm upper colour blue , link 1.25 ton (plate xxxi y) , cab base mounting , pipe assy( plate no-a1-7-2 , sl no- 23) , buzzer(plate-c3-2-3) , hinge door (item no-305) , glass front quarter light left hand clear , glass right side quarter light(sl-378) , gaiter hand brake , glass front quarter light right hand clear(plate-b , glass left side quarter light , tube , ferrule for push rods , catch side window lockback (jcb 3dx super page-89) , bty cover (ms-67 , jcb u oblique v) , gaiter gear lever , leaver tipping (plate-vi t-1) , jug oil 200cc , glass six light l h side , side window glass(ms sl-55) , glass six light right side , glass six light rear , door seal left hand (item no-323) , door tinted glass lower , door tinted glass lower(sl no-322) , glass six light right rear side , latch assy inner rh(item no-341) , brush carrier assy(ms-192) , internal puller , glass tinted right (plate-iv r) , door tinned glass upper(item no-321) , door tinned glass upper(item no- 338) , brake shoe(ms-187) , l h cab door upper window glazing(sl-298) , grab sleeve , window tinted glass left hand side(super plate pla , step (plate - iii c) , rear window tinted glass (jcb super page-107) , wind screen(plate-b2-3-5) , window frame left hand slide (item no-354) , pipe exhaust exhaustion(3dx p3-4-2 sl no 14) , tool kit standard(jcb super) item32 nos qty34 nos , unloader valve with inflator (ispl-97) , grab sleev , swivel hook , door painted & sealed left hand(item no-320) , grab sleeve , grab sleeve , silencer exhaust box 240x150mm(p-627) , tool pyramide (plate- xxxi aa-21) , thrurst ring , silencer exhaust turbo(ms sl no 148 , apr-2015) , blank radio aperture (plate ix a) , t handle 1 inch sq drive(be220g fig no-8000) , windscreen front (jcb 3dx super) , liner roof assy (plate iv f) , frame outer rear window(jcb super p-105) , back up tool , roof moulding(plate-iv e-1) , tools kit (set of 41items) , assembly jig , fender rear lh (plate iii j) , kit piston ring o s 05 mm (plate xxxii f) , o ring (plate xxxii l) , seal rear oil (plate xxxii n) , gasket cyl head(plate xxxiii a) , seal bonded (plate xxxiii a) , valve inlet (plate xxxii b) , valve exhaust (plate xxxiii c)