Latest bronze sheet Tenders | Government bronze sheet Tenders

State Government

CTN :45521250

29 Jun, 2026 42.81 Lacs

Jaipur - Rajasthan

Tender For nit 21 work of replacement of submersible pump sets and accessories of tubewell at various locations under uwss chomu under jen section chomu (urban) under sub div chomu in jurisdiction of executive engineer, phed district division ii, jaipur - 2.15 supply & installation of 3 phase isi marked submersible motor pump set of three star or better rating of bee and as per is: 8034-2018 (pump) and is 9283-2013 (motor) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well/dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect.2.15.2 up to 5.5 kw (7.5 hp) & head above 120 mtr., 2.15 supply & installation of 3 phase isi marked submersible motor pump set of three star or better rating of bee and as per is: 8034-2018 (pump) and is 9283-2013 (motor) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well/dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect.2.15.4 7.5 kw (10 hp) & head above 120 mtr., 2.15 supply & installation of 3 phase isi marked submersible motor pump set of three star or better rating of bee and as per is: 8034-2018 (pump) and is 9283-2013 (motor) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well/dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect.2.15.6 9.3 kw (12.5 hp) & head above 120 mtr., 2.18 supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star-delta starter, over load relay, ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lighting arrangement etc complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom). all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be of minimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm) duly bolted/screwed with enclosure box having 4 legs, each leg s length 18 and double door including in built locking system. the legs should be embedded in m-15 cement concrete plat form. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply.2.18.1 above 5 hp and up to 10 hp, 2.18 supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star-delta starter, over load relay, ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lighting arrangement etc complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom). all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be of minimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm) duly bolted/screwed with enclosure box having 4 legs, each leg s length 18 and double door including in built locking system. the legs should be embedded in m-15 cement concrete plat form. t

corporations/Associations/Others

CTN :45551623

29 Jun, 2026 14.37 Lacs

Etah - Uttar Pradesh

Tender For supply of jointing sheet met st 54 size 5 mm , jointing sheet style - 54, 0.5 mm , jointing sheet style - 54, 1 mm , jointing sheet style - 54, 2 mm , jointing sheet style - 54, 3 mm , gland packing n-m style 1100 10mm , gland packing n-m style 1100 12mm , glandpkg champ sty1100 16mm , oil jointing sheet style 59 size 1 mm

CTN :45388145

15 Jun, 2026 1.50 Lacs

Leh - Jammu And Kashmir

Tender For corrigendum : supply of wd-40 , steel angel 20x20x3m , lt wire , jointing sheet 0.8m thick 1.6m , fevicol sr 998 , welding mesh , alcohol isopropyl technical , cotton tape , nitrogen gas , leather cloth black , leather cloth white , varnish black japan 200ml

CTN :45543630

29 Jun, 2026 4.96 Lacs

Nanpara - Uttar Pradesh

Tender For supply of grease graphite packing non metelic , steam packing metalic style 600 size 6 mm , steam packing metalic style 600 size 10 mm , steam packing metalic style 600 size 12 mm , steam packing metalic style 600 size 8 mm , white dry asbestos rope style 1000 size , high pressure steam jointing sheet metalic , low pressure steam jointing sheet non metelic , grease graphite packing , white dry asbestos rope style 1000 size 6.00mm rd , grease graphite packing non metelic style 1800 size 8.00 mm , asbestoswebbing tape , asbestos yarn style 1056 size 3mm , white dry asbestos rope style 1000 size 16.00mm * /bid number : gem/2026/b/7662260 + /dated: 13-06-2026 ' ' / bid document 1 / 17

CTN :45538201

22 Jun, 2026 2.99 Lacs

Parganas - West Bengal

Tender For supply of kit seal slow swing,adopter air filing,air filter inner,air filter outer,fuel filter assembly,clamp shovel jack seal,fuel filter,oil filter,fuel strainer,air cleaner filter,hydraulic element,element filter,jointing sheet 2m x 2m,alternator 24v,self starter,rock breaker pipe,pin lock,control cable

corporations/Associations/Others

CTN :45084573

15 Jun, 2026 4.92 Lacs

Bardhaman - West Bengal

Tender For bid to ras bid to ras supply of ss shims and oh consumables c c - shims size 0 05mm material ss 304 non magnetic , shims size 0 1mm material ss 304 non magnetic , shims size 0 15mm material ss 304 non magnetic , shims size 0 2mm material ss 304 non magnetic , nonmagnetic shim material ss 304 width 01 mtr thickness 0 25 mm , shims size 0 3mm material ss 304 non magnetic , nonmagnetic shim material ss 304 width 01 mtr thickness 0 5 mm , shims size 1mm material ss 304 non magnetic , stainless steel ss 304 shim of thickness 2 mm non magnetic , non magnetic stainless steel ss 304 shim of thickness 3 mm , hylomer universal blue 100 gm pack , moly kote p 37 moly kote p 37 molikote p 37 paste in 1 kg container make dow corning , lead sheet pure size 1 2 mtrx1 2 mtrx1 2 mm , molykote 1000 , paste steam seal jointing stage b steam seal jointing paste b in 1 kg container make jayantilal gandhi chemical pvt ltd ) /bid number : gem/2026/b/7433774 * /dated: 05-05-2026 & & / bid document 1 / 18

State Government

CTN :45397974

18 Jun, 2026 80.77 Lacs

Kota - Rajasthan

Tender For corrigendum : work of name :- remaining work pkg. no. rj-23-10/srf (rr) / np / 2022-23 distt kota - providing, laying and spreading and compacting specified graded crushed stone in sub-base course including premixing the material at omc in mechanical mixer (pug mill), carriage of mixed material, laying in uniform layers with motor grader, f.e. loader, on a prepared surface and compacting with vibratory compactor to achieve the desired density including all material, labour, machinery, lighting barricading and maintenance of driversion complete. (morth specification clause 401). with all lead & lift, fdkuiqjk rfd;k ls punzsly, total, kilometre stone reinforced cement concrete m15grade kilometre stone of standard design as per irc:8-1980, fixing in position including painting and printing etc ordinary kilometer stone (precast), fdkuiqjk rfd;k ls punzsly, e.mkuk ls guksfr;k, total, kilometre stone reinforced cement concrete m15grade kilometre stone of standard design as per irc:8-1980, fixing in position including painting and printing etc hectometer stone (precast), fdkuiqjk rfd;k ls punzsly, e.mkuk ls guksfr;k, total, providing and erecting typical citizens information board as per approved drawing & specification of mord, made of two ms sheet of 1.6 mm thick each of size 900 mm 750 mm stiffened by angle iron 25 mm 25 mm 3 mm all around the plate and plates fixed on frame of 75 mm dia pipe of 12 swg sheet (vertical post 3050 m with angle holdfasts and horizontal member 900 mm) to be joined by 5 mm thick ms plate at 12 places (65 50 mm) duly embedded in cement concrete m-15 grade of block of 600 mm 600 mm 750 mm size below ground level as per enclosed drawings & as directed by engineering - in-charge. all ms will be stove enameled on both side, lettering, figuring and border will be with ready mixed synthetic enamel paint of superior quality in required shade and colour etc. complete in all respect. all sections of framed post and steel tube will be painted with primer and two coat of epoxy paint as per drawing and as per mord specification., fdkuiqjk rfd;k ls punzsly, e.mkuk ls guksfr;k, total, providing and laying reinforced cement concrete pipes np-3 for culverts including jointing ends and fixing collar with cement mortar 1:2. (morth specification : clause 1000/2900). 300 mm dia, fdkuiqjk rfd;k ls punzsly, e.mkuk ls guksfr;k, total, dry lean cement concrete sub - base. construction of dry lean cement concrete 1:3:6 sub-base over a prepared sub-grade with coarse and fine aggregate conforming to is: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blening to be as per table 600-1, cement content not to be less than 200 kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonne vibratory roller, finishing and curing., fdkuiqjk rfd;k ls punzsly, total, providing and laying un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub-base with 43 grade cement, coarse and fine aggregate conforming to is:383, maximum size of coarse aggregate not exceeding 25mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or fix form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures and vacuum processing pump as approved, curing compound, finishing to lines and grades as per drawing as per morth specification : clause no. 602, 112. using cement concrete m-30 pavement grade, fdkuiqjk rfd;k ls punzsly, total, earthwork in excavation for foundation of structure complete with all l

Central Government/Public Sector

CTN :45382462

15 Jun, 2026 NA

Bangalore - Karnataka

Tender For corrigendum : procurement of electrical spare items for electrical estate, bel bangalore - procurement of electrical spare items, switch sp,5amps,flush mounting (bel part no.990110006826), universal socket 5a (bel part no.990110005759), capacitor 2.25mfd (bel part no. 990110511808), open dp switch 32a (bel part no.990010298004), electronic regulator (bel part no.990072007852), heating element for geyser 2 kw (bel part no.990174051270), immersion heating element (bel part no.990110134672), water heater element round type (bel part no.990010298974), water heater element oveltype (bel part no.990010298295), thermostat (bel part no.990010074031), rigid pvc conduit 1" (bel part no.990010000666), pvc pipe-3/4"(19mm)dia (bel part no.990072023178), gangway box 1way (bel part no.990110027972), exhaust fan 250mm plastic body (bel part no.990010265412), insulation tape (different colours) (bel part no.995010234008), bioline gel(petrolium gelly) (bel part no.990210001351), hylum sheet 2400mmx1200mmx3mm-white (bel part no.990010000903), pvc casing & caping 20mm white (bel part no.990110020891), pvc casing caping 1" (bel part no.990010000434), piercng connectrs,16-95sqmm(abc) (bel part no.990010000693), led bulb 7w warm light (bel part no.990010204787), 50w led flood light luminaire (bel part no.990010002082), 200w led flood light (bel part no.990010213032), street light led fitting, 150w (bel part no.990010000994), led post top light fitting 40w (bel part no.990010224284), 4 sq mm, pvc, multistrand, cu wire (bel part no.990010000736), 2.5 sqmm, pvc, multistrand cu wire (bel part no.990010000735), 1.5sqmm, pvc multistrand copper wire (bel part no.990010000271), twin flat 1sqmm 2core cable (bel part no.990010298101), 2.5 sq-mm - 3core cu- cable (bel part no.990010000125), cable al armoured 4core,10sqmm (bel part no.990110033210), cable aluminium,4 core,16sqmm (bel part no.990110033113), al.flat cable 2.5sqmm,twin cor (bel part no.990110077636), al 2x16sqmm abc 2core cable (bel part no.990010297907), heat shrinkable cable jointing straight (bel part no.990074009447), cable jointing kit for 25 sqm (bel part no.990074008865), 1.1kv heat shrk st.jt-kit-3.5gx50sqmm (bel part no.990010190722), 1.1kv heat shrk st.jt-kit-3.5gx95sqmm (bel part no.990010190916), 10a - switch (make-anchor roma). (bel part no.990072037534), metal cutting blades (bel part no.995010827066), hole saw cutter 18mm (bel part no.990310305230), hole saw cutter 25mm (bel part no. 990310305327), hole saw cutter 30mm dia (bel part no.990010197124), hole saw cutter 50mm dia (bel part no.990010197221), high speed steel drill bit set (bel part no.990210763345), flat spaner set (bel part no.995010290462), rong spaner set (bel part no.995010290559), smc junction box 240x130x110mm2 (bel part no.990010002046), smc meter box (bel part no.990410000115), smc meter box (bel part no.990010000290), air blower (bel part no.990210742490), hot air blower (bel part no.990010272202)

corporations/Associations/Others

CTN :45492328

24 Jun, 2026 30.85 Lacs

Sonbhadra - Uttar Pradesh

Tender For supply of , taflon gland rope seal oil valve size 4x4 sqmm , taflon gland rope seal oil valve size 6x6 sqmm , taflon gland rope seal oil valve size 8x8 sqmm , taflon gland rope seal oil valve size 10x10 sqmm , m s coupling bolt for dc seal of oil pump full thread , galvanized ht nut bolt with 2 nut 2 flat washer 1spring washer 12x75 mm pitch 1point 5 mm full thread , nipple for h2 gas filling regulator 36x34mm brass make , o ring of size od 50mm id 44mm thick 3mm , o ring of size od 52mm id 44mm thick 4mm , o ring of size od 55mm id 45mm thick 5mm , o ring of size od 60mm id 54mm thick 3mm , copper pipe id 5mm od 8mm length 2mtr , copper washer id 8mm od 14 mm thickness 2mm , industrial h2 gas filling pipe reinforced by wire mesh id 10mm od 16mm , oil gauge glass set with fitting for hydraulic tank , industrial grade h2 gas filling regulator for a generator of a 200mw unit inlet pressure 125 150kg cm2 outlet pressure 3 4kg cm2 safety and testing as per peso guidelines , perplex container for 15 75 kv bus duct complete set , portable hydrogen gas leak detector , brass make hexagonal nut for h2 filing post valve , caf jointing sheet 59 oil 1 0 mm 1x2 meter , ms coupling bolt for ac seal of oil pump full thread , dc seal oil pump rpm 2900 head 120m complete mechanical seal set single inside , ac seal oil pump rpm 2900 head 120m complete mechanical seal set single inside , 1cx2 5 sq mm 1 1kv grade single core cu conductor pvc bundle of 90m red yellow blue insulated wire as per is 694 make havells , ss 304 bolt with 2 nuts 2 flat washers 1spring washer 12 5x70 half thread , handheld insulation tester megger 1kv type rechargeable make megger , digital multimeter , roller bearing no 306 , caf jointing sheet 59 oil 2 0 mm 1x2 mete , caf jointing sheet 59 oil 3 0 mm 1x2meter , caf jointing sheet style 54 n m 0 5mm 1x2 meter , caf jointing sheet style 54 n m 1 5mm 1x2 meter , brass bolt with fixed washer and 1 flat washer for slip ring carbon brush size 6x12mm , brass make extension nipple for h2 post valve , brass make hexagonal nut 2 flat washers and 1 spring washer for the co2 filling post valve , brass nut bolt and 1 no fixed and 1 no flat washer for slip ring 8x35mm , brass plug for h2 gas cooler , brass plug for seal oil cooler , brass strip for slip ring carbon brush holder 17x47x1 soft metal as per sample , insulating flat washer made of glass textolite 5mm thick id 10mm od 26mm , insulating flat washer made of glass textolite 5mm thick id 12mm od 28mm , insulating flat washer made of glass textolite 5mm thick id 18mm od 40mm , insulating flat washer made of glass textolite 5mm thick id 22mm od 44mm , insulating flat washer made of glass textolite 5mm thick id 24mm od 48mm , insulating flat washer made of glass textolite 5mm thick id 26mm od 50mm , insulating flate washer made of glass textolite 5mm thick id 28mm od 52mm , insulating fiber sleeve having dimension id 10mm od 13mm length 2mtr , insulating fiber sleeve having dimension id 12mm od 16mm length 2mtr , insulating fiber sleeve having dimension id 16mm od 20mm length 2mtr , insulating fiber sleeve having dimension id 20mm od 25mm length 2mtr , insulating fiber sleeve having dimension id 8mm od 11mm length 5 mtr complete pipe without a cut , insulating fiber glass sheet size 1x2 mtr and thickness 5mm , ss bolt 12 5x80mm half thread thread and micro pitch with following size 12 5x80 mm , ss bolt with 2 nut 2 flat washer 1spring washer having micro thread and micro pitch with following size 12x80 mm , ss bolt with nut and 2 no flat washer and 1 no spring washer having micro thread and micro pitch with //bid details 2 / 93 following size 36x70 mm , bimetallic strip 100x50 mm , gun metal make carbon brush holder for generator , pvc hose pipe 1 point 25inch , hydraulic tank looking glass looking glass transparent toughened heat resistant up to 300 deg c glass thickness 14mm moc toughened glass with sealing , damper tank looking glass looking glass transparent toughened heat re

CTN :45505722

20 Jun, 2026 NA

Pathankot - Punjab

Tender For supply of insulation tape , wd 40 , glue gunstick , cable electric atc elastomer insulated , drill bit , sheet cellular fhom sheet 3 inch foam , plywood for general purpose 3 ply , leather cloth black , washers plain steel 14mm , washers plain steel 17mm , washers plain steel 20mm , jointing sheet 1.5mm

Bronze Sheet Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

corporations/Associations/Others

corporations/Associations/Others

State Government

Central Government/Public Sector

corporations/Associations/Others