Latest brushing machine scrap Tenders | Government brushing machine scrap Tenders

CTN :40568259

23 Jun, 2025 NA

Darjeeling - West Bengal

Tender For supply of locking pin , front roll , front axle , bushing , grease nipple for front roll , end cap , segment bolt , key washer , grease nipple , bolt for worn case cover , bolt for key washer , dust guard lh , dust guard rh , driving ring , hex bolt , spring washer , locking wire , die , pin lever , selector arm shaft , bolt , fulcrum pin , guide bolt , bolt for cover , stud , shim set , distance piece , bolt with nut and locking , distance washer , distance tube , nut and pin , bush , oil seal , set screw , rear clamp plate , main bearing housing , lock nut , inner distance piece , front clamping plate , cheese head bolt , clutch casing , clutch facing ring , cheese head bolt with nut , driving pin , clutch pressure ring , eye bolt , pin for clutch link , clamping plate , roller bearing , clutch link , clutch driver , pin for clutch casing bid number/ & ( * ) : gem/2025/b/6281668 dated/ + : 02-06-2025 bid document/ 2 2 1 / 53

Central Government/Public Sector

CTN :40330612

11 Jun, 2025 37.97 Lacs

Faizabad - Uttar Pradesh

Tender For corrigendum : tender for supply of supply of bakelite sheet with 1nos of 6a dp mcb and stud type connector suitable for 4cx 6sq mm cable complete as required. , supply of 25w led street light luminiare with pre die cast aluminium housing and ip 66 protection , pf greater than equal to 0.95 , thd less than 10 percent , cri greater than equal to 70 as per technical specification complete as required. , supply of lt power cable of 1.1 kv grade of following sizes aluminium conductor xlpe insulated pvc sheathed armoured cable confirming to is 7098 part-i-1988 with upto date ammendment as required. a) 3.5 c x 95 sq. mm , supply of lt power cable of 1.1 kv grade of following sizes 4c x 6sq.mm(copper conductor) , supplying and laying of following size dwc hdpe pipe isi marked along with all accessories like socket , bend , couplers etc. conforming to is 14930 , part ii complete with fitting and cutting , jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required. a) 63 mm dia (od-63 mm & id-50 mm nominal) , laying of one number pvc insulated and pvc sheathed/xlpe power cable of 1.1kv grade of following size in the existing rcc/gi/hume/metal/hdpe pipe etc. as required. a) above 35sq.mm and up to 95 sq mm , laying of one number pvc insulated and pvc sheathed/xlpe power cable of 1.1kv grade of following size in the existing rcc/gi/hume/metal/hdpe pipe etc. as required. b) up to 35 sq mm , supplying and making end termination with brass compression gland and aluminium lugs for following size of pvc insulated and pvc sheathed / xlpe aluminium conductor cable of 1.1 kv grade as required. a) 3.5c x 95 sq.mm , supplying and making end termination with brass compression gland and aluminium lugs for following size of pvc insulated and pvc sheathed / xlpe aluminium conductor cable of 1.1 kv grade as required. b) 4c x 6sq.mm(copper conductor) , itc of gi octagonal pole of following length in reinforced cement concrete 1 ratio 2 ratio 4 (1 cement 2 coarse sand 4 stone aggregate 40mm nominal size) foundation i/c excavation and refilling etc. complete as required a) 5 mtr. height , itc of 30w led street light luminiare on existing pole bracket i/c connection with 1.5sq.mm frls copper wire complete as required. , earthing with g.i. earth plate 600 mm x 600 mm x 6 mm thick including accessories , and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. , providing and fixing 25 mm x 5 mm g.i. strip in 40 mm dia g.i. pipe from earth electrode including connection with g.i. nut , bolt , spring , washer excavation and re-filling etc. as required. , earthing with g.i. earth pipe 4.5 metre long , 40 mm dia including accessories , and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. , providing and laying earth connections , from earth electrode with 6 swg dia , g.i wire in 15mm dia , g.i pipe from earth electrode including connection with g.i. thimble excavation and re-filling as required. , providing and fixing 6 swg g.i. wire on surface or in recess for loop earthing alongwith the existing cable as required. , design , fabrication , supply , installation , testing & commissioning of outdoor feeder pillar , cubicle type , made out of 2 mm thick crca sheet , totally enclosed , ip 55 , free standing , floor mounting , dust and vermin proof , indoor , compartmentalised , suitable for operation on 3 phase and neutral , 415 v , 50 hz ac system , including internal wiring with suitable size wires/cable , interconnection , duly powder coated painting etc. , including supply & installation of following switchgears , metering instruments and accessories in the feeder pillar as required as per attached boq in atc , shifting of 5 mtr height str

CTN :40510054

09 Jun, 2025 NA

West Singhbhum - Jharkhand

Tender For supply of indoor type 18w led tube light fitting complete nos. luminaire with surface/ wall m ounted led batten with high pressure die-cast aluminum with adc 12 alloy housing or crca sheet (0.6 mm thick) powder coated to white colour suitable for 140-270v, cri 280, pf >= 0.90 at full load, colour temper ature 6000+500 k, working temperature -10 degree c to 50 degree c, luminaire efficacy>= 110 im/w, ip 2 0, surge protection- mov of 2.5 kv (on board), burning hours 2 50000 with all accessories with suitable arr angement for fixng on wall with all the accessories. the luminaire shall conform to is 10322-5-1 (2012) wit h latest amendment if any. driver type - constant current driver with short circuit & open circuit protection. the firm has to submit technical parameters as per annexure a of specification no. pcee/s/185/led/12/21/ rev-0, dec-2021. the complete luminaire shall have replacement guarantee for satisfactory performance a nd manufacturing defects for a period of 60 months from date of commissioning or 72 months from date of supply whichever is earlier. led based luminaire shall be conforming to specification no. cee/s/185/led/12 /21/rev-0, dec-2021. make: philips, bajaj, orient, surya, havells, crompton, syska, goldwyn. [ warranty p eriod: 72 months after the date of delivery ]

State Government

CTN :40495651

10 Jun, 2025 NA

Pune - Maharashtra

Tender For providing supplying and erecting various different electric material for 1 year at grampanchayat(fund) - electric material for 1 year, 11/4" gi pl pipe, 3/4 " gi pl pipe, g.i.pipe 1-2, g.i.pipe 1*1/2"r, 1.5mm polycab 90mtr, 1.5sqmm 3c cu flex wire, 16*4 c alu armd cable, 2.5 mm polycab /syska 90mtrs, 4.0 sq mm service wire heavy, 4 mm polycab 90 mtr, 6 sqmm x 2 c service wire, g.i.wire, wire 16sq mm 4c alu arm, 120w led driver 10amp, led chip 100w, led chip48w, led chip 50w, led driver 100w, led driver 36w, led driver 48w, led driver 60w, led driver 65w, mcb 63am/2p, mcb box 2way, mcb single pole, mcb s.p 40amp, meter box 2*2.5 gi, mnx45 240v contactor, mnx 50 contactor coil, mnx50 contactor l & t, 32amp single pole main switch, 50w led flood light, led flood 100w, led street light s40 30w, 1 x 36 lx pl street light fitting, 2 x 36 w pl alu fitting, led lamp 45w, led pll 18w, led solar street light 40w, led streetlight 36w, led streetlight 50w, 63a kitkat fuse, 63 amps /415 v smtp main switch, 48" ceiling fan, ballast 36/40w destello electronic, battery 12v, busbar 200a/415v, cable tie 100 mm, cable tie 300mm, crement pole clamp, fan 16 wallfan cromton, fan 24 crompton celling, finolex pl 36w cdl pl tube 36w 4 pin, flood light 100w, gic qt timer, hallogen fitting 500w, hallogen lamp 500w, halonix led lamp 09w, halonix led lamp 20w, halonix led lamp 50w, holder porcelain e27, holder pvc 36w pl, led streetlight 36w, led street light 48w, kit kat fuse 16a/415, led batten 20w, led batten 36w, plier 8" taparia, pvc tapes/g 8mtr, rawal plug 25*8, rawal plug 35*8, screw 25*8, screw 35*8, screw 75*8, service insulator, sholder gun, sholder pest, sholder wire, streetlight 1*36 cfl eco, t-5 clip, taparia tester 813 yellow, timer for street light, tourch rechargable, 5meter ms pole, 7meter ms pole, 9meter ms pole, streetlight pole bracket single arm, streetlight pole bracket double arm, streetlight pole bracket junction box, pl tube light 4 pints lamps, 36 w choke pl osaram 4 pins, 36 w led bulb, 18 w led bulb, 15 w led bulb, 40 w led bulb, 2 core service wire 6mm, mnx 50 contactor l&t, coil for mnx 50 l&t, 2 core service wire 4mm, 50 w led bulb threded, panle box gi single dore 1.5*2, panle box gi double dore 2.5*2, 6 amp 5 pin socket, 6 amp switch, fan dimer socket type, board modle 4*4, board modle 8*8, board modle 8*16, 10 mm 4 aluminium armand cable, 3.5 mfd kadser, mcb 32 amp/2p, led flood 250w, pvc pipe 1", wall can, battery 100 amp, main switch 63 amp 3 pole, kit kat fuse 63 amp, kit kat fuse 32 amp, 16 meter ms pole, 30 w led repair, 36 w led repair, 48 w to 50 w led repair, 70 w to 75 w led repair, 100 w led repair, 75 w flood light repair, 100 w flood light repair, 125 w flood light repair, 150 w flood light repair, supplying and erecting m.s. pipe pole b grade 80 mm dia 6 m long with pole cap, base plate in provided foundation as per specification no. oh-pl/gip+b131:b141, making cement concrete foundation including excavation (60 * 60 * 150) cm deep in 1:3:6 cement concrete 20 * 25 mm stone metal, (45 * 45 * 45) * cm / 45 cm dia. x 45 cm height plinth duly plastered, with necessary curing and finishing complete. (above 6 m to 9 m poles), supplying and erecting led street light fitting suitable for above 70w-75 lamp, including lamp, with pf > 0.95 class ip 65 and above housing of pressure die cast alluminium alloy and heat sink extruded alluminium complete per specification no fg-odf/fls, providingt and erectinggalvanised 1000mm single arm sword type bracket with frp dome and ball as per specification no. oh-pl/pbkt, supplying, erecting & making dpmcb 6 a to 32 a in provided distribution board, supplying and erecting mains with 2x 2.5 sq mm frlsh copper pvc insulatedwire laid in prouied candot/trunking/insidepole/busbor or any other place as per specification wg/ma/bw, providing pipe type earthing with 40mm dia. gl pipe or 20mm dia. gi rod complete with all materials, supplying and erecting mains with isi mark

Central Government/Public Sector

CTN :40501084

18 Jun, 2025 NA

Multi City - Multi State

Tender For supply of rechargeable led work light 18 watt with aluminium die cast housing in premium power coa ted finish, strength: 6 cree leds of 3 watt each produces flooring light of 1000 lumens without any heat di spense, with charger. 4 strong magnets on the bottom. spec- led power-18 watt, voltage ac: 115-220 v, charging time- 8 hrs, run time- 7 hrs, battery voltage-3.7 volt, battery cap-6600 mah, li-ion battery, lume n-1000lm, light beam size-10m, waterproof & dust proof rating-ip65, material aluminium & pc housing- pmm a lens. model no- groz led/621 or similar. [ warranty period: 30 months after the date of delivery ]

Central Government/Public Sector

CTN :40473516

16 Jun, 2025 NA

Ahmedabad - Gujarat

Tender For (supply)-supply of led bulkhead fitting, capacity 20 watt, operating voltage range (in volts) 75 to 160, & rated voltage (in volts) 75 to 140, v ac 1 phase 50hz, power factor > / = 0.9, color temperature (k) : 6000+/-500, over all efficiency: 120 lumen per watt, beam angle 120 degree, white color, protection ip-67, housing-pressure die cast aluminum powder coated housing, visor-polycarbonate based material cover, gasket-silicon material based gaske t, connected wire-3 core 0.75 to 1 sq mm pvc copper with 0.5 mtr length, wall mounted ( oval shape) make:- philips, crompton, wipro, jaquar, havells, poly cab only. [ warranty period: 30 months after the date of delivery ]

corporations/Associations/Others

CTN :40405223

03 Jun, 2025 18.00 Lacs

Porbandar - Gujarat

Tender For annual rate contract for supplying of electric material for the financial year (year 25-26) second attempt - providing mains with 1.1 kv grade frls pvc insulated isi marked stranded alluminum conductor wire. standard company like, havells, finolex, kei, rr kebel, polycab, etc. (4mm isi alluminum wire), providing mains with 1.1 kv grade frls pvc insulated isi marked stranded alluminum conductor wire. standard company like, havells, finolex, kei, rr kebel, polycab, etc. (6mm isi alluminum wire), fuse with isi standard (copper part) 63 amp, fuse with isi standard (copper part) 100 amp, fuse with isi standard (copper part) 200 amp, supplying led street light / flood light fittings with high power white leds wattage of 1watt and above assembled on single mcpcb, efficiency more than 130 lm/w and corrosion free high pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium with diffuser and polycarbonate optics/ lenses with company mark/name engraved or embossed 120 to 300v, power factor more than 0.95, thd 0.45, luminaire efficacy > 100 lumens/watt. led driver efficiency > 85 percentage. cree / osram / philips lumileds / nichia / seoul/ bridgelux (u.s.a.) make led used for luminaire. (fittings required lm-79 & lm-80 certificates) (note: below description have shown ranges of wattage capacity of led fittings. the engineer incharge may select any wattage capacity between the ranges shown.) (20 watt), supplying led street light / flood light fittings with high power white leds wattage of 1watt and above assembled on single mcpcb, efficiency more than 130 lm/w and corrosion free high pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium with diffuser and polycarbonate optics/ lenses with company mark/name engraved or embossed 120 to 300 v, power factor more than 0.95, thd 0.45, luminaire efficacy> 100 lumens/watt. led driver efficiency > 85 percentage. cree / osram / philips lumileds / nichia /seoul/ bridgelux (u.s.a.) make led used for luminaire. (fittings required lm-79 & lm-80 certificates) (note: below description have shown ranges of wattage capacity of led fittings. the engineer incharge may select any wattage capacity between the ranges shown.) (24 watt), supplying led street light / flood light fittings with high power white leds wattage of 1watt and above assembled on single mcpcb, efficiency more than 130 lm/w and corrosion free high pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium with diffuser and polycarbonate optics/ lenses with company mark/name engraved or embossed 120 to 300v, power factor more than 0.95, thd0.45, luminaire efficacy> 100 lumens/watt. led driver efficiency>85 percentage. cree / osram / philips lumileds / nichia / seoul/ bridgelux (u.s.a.) make led used for luminaire. (fittings required lm-79 & lm-80 certificates) (note: below description have shown ranges of wattage capacity of led fittings. the engineer incharge may select any wattage capacity between the ranges shown.) (30 watt), supplying electrical insulation l.t. tape role with isi marked having nominal width 1.8 mm nominal length 9.0 mtr nominal thickness 0.125 mm and having self adhesive pvc. any colour, street light driver 20 watt, street light driver 35 watt, street light driver 30 watt

State Government

CTN :40425610

04 Jun, 2025 NA

Mulshi - Maharashtra

Tender For providing all types of electrical and electronic equipment in gram panchayat hinjawadi during the financial year 2025-26. - electrical material, supplying and erecting modulartype switch6a / 10a isimark approved make duly erected on provided plate and box with wiring connections complete.(8-1-2), supplying and erecting street light bracket for erection ofsingle fitting made from 40 mm. dia b class g.i. pipe 1.0 m in length along with pole cap of 300 mm length 100 mm dia duly welded as per specification no., providing cement concrete foundation including excavationfor the poles 60 cm x 60 cm x 1.5 m deep in 1:3:6 cement concrete (20 x 25 mm stone metal) and 45 cm x 45 cm x 45 cm/45 cm dia. x 45 cm height plinth duly plastered and with necessary curing and finishing in an approved manner.(for 8.5 to 9 m poles) (16-3-2), supplying and erecting steel tubular swaged pole 139.7 x 114.3 x 88.9 mm. dia with 4.5x3.65x3.25 mm thickness (4.5 + 1.75 + 1.75m) length respectively and total 8 m long with pole cap, base plate in provided foundation.(weight 101 kg.) as per specification no.oh-pl/stp, supplying and erecting steel tubular swaged pole 165.1 x 139.7 x 114.3 mm. dia with 4.5 x 4.5 x 3.65 mm thickness ( 5 + 2 + 2m ) length respectively and total 9 m long with pole cap, base plate in provided foundation (weight 147 kg) as per specification no. oh-pl/stp, supplying and erecting steel tubular swaged pole 165.1 x 139.7 x 114.3 mm dia. with 4.5 x4.5 x3.65 mm thickness (5.60 + 2.7 + 2.7 m) length total 11 m long with pole cap, base plate in provided foundation (weight 175 kg.) as per specification no. . oh-pl/stp, supplying and erecting street light bracket made from 25mm. dia b class g.i. pipe, 0.6m. in lengthalong with polecap of 300 mm length and 80 mm dia duly welded with provided leads as per specification, supplying,tpmcb 40a to 63a in provided distribution board, providing pair of duly tested rubber hand gloves as per is:4770 suitable for working upto 22kv supply., supplying and erecting insulated d.p. switch surface type/flush type 32a 240vwith indicator lamp & fuse, supplying h.c. pattern porcelain fuse bridge swith base & hc type fuse links240v 32a, supplying and erecting programmable digital almanactimer microcontroller based with real time clock to operate on derived switching on & switching off street light as per daily sunset and sunrise respectively, 1.25 mm crca sheet metal enclosures with 20a., supplying pvc insulated pvc round sheathed 1.5 sq.mm (30 no. x 0.25 mm dia.) 3 core flexible multi stranded copper industrial cable for voltage grade up to 1.1 kv (1-3-29), supplying and erecting led street light fitting suitable for 60w lamp, including lamp, with pf > 0.95 class ip 65 and above housing of pressure die cast alluminium alloy and heat sink 2-9-5, supplying and erectingled street light fitting suitable for 26w to 36w led street light, including lamp, with pf > 0.95 class ip 65 and above housing of pressure die cast alluminium alloy and heat sink 2-9-5, supplying and erectingled street light fitting suitable for 90 w led street light, including lamp, with pf > 0.95 class ip 65 and above housing of pressure die cast alluminium alloy and heat sink 2-9-5, supplying and erecting led flood light fitting of 120w, including lamp, with pf > 0.95,class ip 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete per specification no fg odf/fls-2, supplying & laying pvc armoured cable 4core 6sq mm, supplying & laying pvc armoured cable 4core 10 sq mm 7-1-15, supplying & laying pvc armoured cable 2core 10 sq mm, supplying & laying pvc armoured cable 4core 16 sq mm, supplying, erecting & marking spmcb 6a to 32a, b- series (for lighting) 5-3-3, supplying, erecting & marking dpmcb 6 a to 32 a bseries (for lighting) 5-3-7, supplying, erecting & marking tpmcb 6 a to 32amp in provided distribution board 5-3-14, supplying, erecting & marking fpmcb 40a

State Government

CTN :40429074

02 Jun, 2025 1.69 Lacs

Ahmedabad - Gujarat

Tender For supplying material to e.i work at shahibaug section, ahmedabad as per requirement.-, , supplying following type of modular type accessories with necessary connection. as desired by engineer in charge, , (as per requirement), , (1) 6 amp. sp one way switch, , (2) 16 amp. sp one way switch, , (3) 6/16amp. universal socket, , (4) 6 a socket, , supplying mains with 1.1 kv grade frls pvc insulated isi marked stranded copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor frls pvc insulated stranded wire of green colour for earth continuity of following size., , (as per requirement), , (a) with medium class rigid pvc pipe and accessories, , (a) 2 wire 1.5 sq. mm, , (b) 2 wire 2.5 sq. mm, , supplying mains with 1.1 kv grade frls pvc insulated isi marked stranded copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor frls pvc insulated stranded wire of green colour for earth continuity of following size., , (as per requirement), , (a) with medium class rigid pvc pipe and accessories, , (a) 2 wire 4 sq. mm, , supplying flexible pvc insulated multi strand multi core 1.1 kv grade isi marked copper wires of following size to be erected as directed., , (as per requirement), , e) 1.50 sq.mm 3 core round pvc sheathed, , supplying following shockproof tissino type accessories erected on 3 mm thick pc (polycarbonate) sheet in pvc/metal/wooden box. erected on wall/ceiling., , (as per requirement), , (1) one no single pole 6 a switch / bell push, , (2) one no 3/5 pin 6 a socket, , (6) one no single pole 16 a switch & one no 6a/16 a universal socket combined with indicator & fuse, , (7) bakelite ceiling, rose, , (8) bakelite lamp holder, , (14) electronic hum free eme socket type steps fan regulator, , supplying bakelite adopter for holder to be erected., , (as per requirement), , supplying 5a, 10 way bakelite connector duly erected on existing board., , (as per requirement), , supplying isi marked 3 pin plug top., , (as per requirement), , (a) for 5/6 a., 240 v, , (b) for 15/16a, 240 v, , supplying decorative call bell ting-tong box type 250 volts complete erected., , (as per requirement), , supplying electrical insulation l.t. tape role with isi marked having nominal width 1.8 cms nominal length 9.0 mtr nominal thickness 0.125 mm and having self adhesive pvc, , supplying led indoor fittings with leds of wattage 0.2, , watt to 0.5 watt assembled on single mcpcb, with, , housing used as a heat sink shall be made of thick sheet steel conforming to is: 513/crca/ aluminium die cast powder coated and high u.v. & corrosion resistance with diffuser with company mark/name, , 120 to 300 v, power factor more than 0.9, thd < 10%,, , cct 3000 k to 6500k,, , luminaire efficacy> 85 lumens/watt, led efficiency-110 lumens/watt, , led driver efficiency > 85%, , cree / osram / philips lumileds / nichia /seoul/bridgelux make led used for luminaire. (fitting required lm-79 & lm-80 certificates) (note: below description have shown ranges of wattage capacity of led fittings.the engineer incharge may select any wattage capacity between the ranges shown.), , (as per requirement), , (a) tube light with integral driver, , (i) 5-10 watts, surge-2 kv, ip-20, conventional 1 to 2 feet, , cat-iii, , (iv) 22-24 watts, surge - 2kv, ip-20, conventional 4 feet, , supplying led lamps with following wattage capacity of 220 to 240 voltage, minimum 15000 burning hours life, 500 v in built-surge protection, polycarbonate diffuser, mounting suitable for e14 / e27 / b22 lamp holders, pf >= 0.5, , (a) led lamps integral type, with pc diffuser suitable, , lamp holder, , (iii) 10 to 15 watts, , cat-iii, , supplying miniature circuit breaker single pole 6a to 25a suitable to operate on 240 v a.c. system and having breaking capacity 10 ka to be erected in existing box. confirming to is 8828/1996 with isi mark., , (as per requirement), ,

CTN :39038241

06 Jun, 2025 10.88 Crore

Gandhinagar - Gujarat

Tender For corrigendum : supply of goods, machine tools & equipment foran international standard itotin mechanic diesel engine (md) tradeat iti bardoli, gujarat, india (package 3: mechanic diesel - files assorted sizes and types including safe edge file(20nos), flat file, second cut, flat file, bastard, grease gun, grease gun heavy duty trolley type, growler, hacksaw frame, hammer ball peen, hammer chipping, hammer copper with handle, hammer mallet, hammer plastic, hand operated crimping tool, hand vice, hollow punch set of seven pieces, insulated screwdriver, insulated screwdriver, left cut snips, magnifying glass, oilcan, philips screwdriver set of 5pieces, pipe cutting tool, pipe flaring tool, pliers combination, pliers flat nose, pliers round nose, pliers side cutting, engine wire harness connected complete with electrical equipment, diesel fuel quality test equipment set, training setup for adas systems, 4-wheel alignment set & hoist with advanced driver assistance systems (adas), training system for sensors in motor vehicles, training system for the basics of pulse generation and ignition in vehicles, training system: common rail diesel injection system, batterycharger, car jet washer with standard accessories, chain pulley block capacity with tripod stand, compression testing gauge suitable for diesel engine with standard accessories, connecting rod alignment fixture, cylinder liner-dry& wet liner, press fit & slide fit liner, different type of engine bearing model, different type of piston model, fuel feed pump for diesel, fuel injection pump (diesel)inline, fuel injection pump dismantling toolkit /universal vice, fuel injection pump ve pump/ distributor fuel rotary pump (dpc) pumps, glow plug tester, injectormulti hole type, pintle type, injector cleaning unit, injector testing set (hand tester), oil pump for dismantling and assembling., piston ring compressor, piston ring expander and remover., piston ring groove cleaner., radiator cut section-crossflow, radiator cut section-downflow, radiator pressure cap, tandem master cylinder with booster, turbo charger cut sectional view, water pump ford is mantling and assembling, workbench with bench vice and storing drawers, arbor press hand operated 2-ton capacity, drilling machine bench to drill, dual magnetization yoke, grinding machine pedestal (general purpose), hydraulic jack, pipe bending machine (hydraulic type), pneumatic rivet gun with standard accessories, tin smiths bench folder, trolley type portable air compressor, special tools and equipment, hydraulic vertical honing machine for engine cylinder and brake bore, pneumatic valve seat grinder and lapping kit, intercooler cut model assembly with air filter & housing assembly diesel engine, work benches with bench vices and storage draws to demonstrate machines, belt tensioner gauge, granite surface plate with stand and cover, marking out table, multi scan tool, spring tension tester, ammeter dc with external shunt, cylinder bore gauge, dc ohmmeter, depth micrometer, dial gauge, multimeter digital, oscilloscope, outside micrometer, outside micrometer, outside micrometer, outside micrometer, sheet metal gauge, straight edge gauge (2ft.), straight edge gauge (4ft.), surface gauge with dial test indicator plunger type, tachometer (counting type), telescope gauge, temperature gauge with sensor, thermostat, timing lighter, tyre pressure gauge with holding nipple, vacuum gauge, vernier calliper, wire gauge(metric), hydrometer, engineers stethoscope, drill twist (various sizes), hand reamers adjustable, drill twist(assorted), set of stock and dies with die stock-metric, taps and dies complete sets(5types), steel rule, caliper inside with spring, caliper outside with spring, dividers with spring, engineers square, feeler gauge 20blades (metric), hand shear universal, bench lever shears, air blow gun with standard accessories, air ratchet with standard accessories, air impact wrench with standard accessories, angle

Brushing Machine Scrap Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

State Government

Central Government/Public Sector

Central Government/Public Sector

corporations/Associations/Others

State Government

State Government