Latest cable tray repair Tenders | Government cable tray repair Tenders

Central Government/Public Sector

CTN :45382837

22 Jun, 2026 NA

Kamrup - Assam

Tender For repair/maint of external electric supply system, distribution lt panels with connected items and allied services at other than basistha area under ge guwahati. - excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep for taking out / laying of under ground cable, pole or stay and getting out in soft soil strata complete all as specified and as directed., returning filling in including spreading leveling watering and well ramming in layers not exceeding 25cms spread any type of soil complete all as specified and as directed., removing excavated materials not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed., supply and lay for dry river sand filling for cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and as directed. (note : punned thickness shall be measured)., m&l for bricks common burnt clay, building brick, sub class b designation 75 old size bricks laid in trenches flat over sand cushioning for cable protection complete all as specified and as directed., m&l for supply and fixing / laying in replacement, connect, test and commissioning of lt under ground cable xlpe insulated, screened, pvc bedded, galvanised steel strip or wire armoured, electric cable (heavy duty) with multistranded aluminium conductor, 1100 volts grade in trenches/on wall/poles laid in ducts/inside protection pipe of the following cross sectional area including cable glands,lugs and suitable size of ms saddle clips (where ever cable laid in ceilings / walls without cable duct) complete all as specified and as directed.note : manufacturers test certificate shall be submitted alongwith rar/fb to engr-in-charge., (a) 95 sqmm x 3.5 core, (b) 70 sqmm x 3.5 core, (c) 50 sqmm x 3.5 core, (d) 25 sqmm x 3.5 core, supply and fixing in repair, connecting, testing and commissioning mccb in panel etc. mccb, tpn (4 pole), 630 amps, 50ka breaking capacity with overload and thermal tripping feature with magnetic release, 415volts ac, 50hz, icu = 100%, including certain addition or alteration if required at site complete all as specified and directed., supply and fixing in repair, connecting, testing and commissioning mccb in panel etc. mccb, tpn (4 pole), 400 amps, 36 ka breaking capacity with overload and thermal tripping feature with magnetic release, 415volts ac, 50hz, icu = 100%, including certain addition or alteration if required at site complete all as specified and directed., supply and fixing in repair, connecting, testing and commissioning mccb in panel etc. mccb, tpn (4 pole), 250amps, 36ka breaking capacity with overload and thermal tripping feature, 415volts ac, 50hz, icu = 100%, including certain addition or alteration if required at site complete all as specified and directed., supply and fixing in repair, connecting, testing and commissioning mccb in panel etc. mccb, tpn (4 pole), 160amps, 36ka breaking capacity with overload and thermal tripping feature, 415volts ac, 50hz, icu = 100%, including certain addition or alteration if required at site complete all as specified and directed., supply and fixing in repair, connecting, testing and commissioning mccb in panel etc. mccb, tpn (4 pole), 125 amps, 36ka breaking capacity with overload and thermal tripping feature, 415volts ac, 50hz, icu = 100%, including certain addition or alteration if required at site complete all as specified and directed., supply and fixing in repair, connecting, testing and commissioning mccb in panel etc. mccb, 4 pole, 100amps, 26ka breaking capacity with overload and thermal tripping feature, 415volts ac, 50hz, icu = 100%, including certain addition or alteration if required at site complete all as specified and directed., supply and fixing in repair, connecting, testing and commissioning mccb in panel etc. mccb, 4 pole, 63amps, 16 ka breaking capacity with

Central Government/Public Sector

CTN :45365822

19 Jun, 2026 39.99 Lacs

Bikaner - Rajasthan

Tender For repair to security lights panels dg sets fire alarm ups with covered items at af stn bikaner under ge (af) nal - excavation in trenches in soft/loose soil not exceeding 1.5 mtr wide and not exceeding 1.5m depth, getting out the excavated earth, forming bottom surfaces to required gradient complete all as specified and directed by engineer-in-charge., removal of excavated material soils to a distance n exc 50 m and depositing where directed at a level not exceeding 1.5m above the startly point complete all as specified and directed., returning filling in, including spreading, levelling watering and well ramming in layers n exc 25 cm as in any type of soil complete all as specified and directed., material and labour for sand cushioning using dry and clean tibba sand in two layers, first layers of 80mm thick before laying of cable and second layer of 150mm thick after laying of cable in trenches/ducts including consolidation of each layers complete all as specified and directed. note : punned thickness shall be measured for payment., material and labour for un-reinforced pre-cast concrete cable covers, class lv type-1, flat size 250mm x 150mm x 40mm thick complete all as specified and directed., taking out defective cable xlpe/pvc sheathed 1100 volt grade heavy duty armoured with aluminum conductor 2 core, 6 sqmm from trenches complete all as specified and directed.note : excavation and earth work shall be measured and paid for separately under relevant item, taking out defective cable xlpe/pvc sheathed 1100 volt grade heavy duty armoured with aluminum conductor 2 core, 10 sqmm from trenches complete all as specified and directed.note : excavation and earth work shall be measured and paid for separately under relevant item, taking out defective cable xlpe/pvc sheathed 1100 volt grade heavy duty armoured with aluminum conductor 4 core, 16 sqmm from trenches complete all as specified and directed.note : excavation and earth work shall be measured and paid for separately under relevant item, taking out defective cable xlpe/pvc sheathed 1100 volt grade heavy duty armoured with aluminum conductor 3.5 core, 25 sqmm from trenches complete all as specified and directed.note : excavation and earth work shall be measured and paid for separately under relevant item, taking out defective cable xlpe/pvc sheathed 1100 volt grade heavy duty armoured with aluminum conductor 3.5 core, 35 sqmm from trenches complete all as specified and directed.note : excavation and earth work shall be measured and paid for separately under relevant item, taking out defective cable xlpe/pvc sheathed 1100 volt grade heavy duty armoured with aluminum conductor 3.5 core, 50 sqmm from trenches complete all as specified and directed.note : excavation and earth work shall be measured and paid for separately under relevant item, supplying, laying, jointing and testing of under ground cable xlpe insulated, 1100 volt grade heavy duty armoured with stranded aluminium conductor 2 core 6 sqmm laid in trenches/duct/pipe including all electrical connection with required lugs and nuts, bolts complete all as specified and directed by engineer-in-charge , supplying, laying, jointing and testing of under ground cable xlpe insulated, 1100 volt grade heavy duty armoured with stranded aluminium conductor 2 core 10 sqmm laid in trenches/duct/pipe including all electrical connection with required lugs and nuts, bolts complete all as specified and directed by engineer-in-charge, supplying, laying, jointing and testing of under ground cable xlpe insulated, 1100 volt grade heavy duty armoured with stranded aluminium conductor 4 core 16 sqmmlaid in trenches/duct/pipe including all electrical connection with required lugs and nuts, bolts complete all as specified and directed by engineer-in-charge, supplying, laying, jointing and testing of under ground cable xlpe insulated, 1100 volt grade heavy duty armoured with stranded aluminium conductor 3.5 core 25 sqmm laid in trenches/duct/pipe inc

CTN :45349762

09 Jun, 2026 2.95 Lacs

Sikar - Rajasthan

Tender For procurement of materials for repair of various components used in the fixing of light poles installed across of the failure different wards within municipal area - 61.13 p/l of double wall corrugated hdpe pipe confirming to is 16205 p-24, stiffness class 750 n, externally corrugated and having smooth surface inside with hdpe coupler, elbow, tee at required depth below the ground for laying cable of following nominal outer dia. mfr test report from nabl accrediated is to be submitted. (excavation of earth & back filling with compaction is to be paid extra) all as per pre approved by engineer in-charge.. for additional technical parameters of products/ work, refer annexure "a" attached with this bsr 50mm dia. , providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed unarmoured copper cable confirming to is:1554 p-i / is:7098 p -i of 1.1 kv with electrolytic grade copper made of copper rods confirming to is 613-1964, of purity >99.7%, inner/outer sheath confirming to is:5831 in existing rcc/hume/stoneware / pvc pipe/open duct/cable trench/cable tray (with cable tie) including testing etc. as required of following size. oem must have it's own in house nabl accrediated laboratory for testing procedure as per is:10810 for additional technical parameters of product / work refer annexure 'a' attached with this bsr 3 core , supplying and making one end termination with nickel plated heavy duty brass single compression gland (as per is 12943-1990)) sibg type consisting of check nut, gland body, metal washer(3 nos.), outer seal rubber ring, compression nut, heavy duty aluminium lugs (as per is 8309-1993) duly crimped with crimping tool, pvc tape as per is 8337-1976 of following size of pvc insulated & pvc sheathed/ xlpe aluminium conductor cable of 1100 volt grade as required.all as per pre approved by engineer in-charge. for additional technical parameters of products/work, refer annexure "a" attached with this bsr 4 x 10.0 sq.mm pvc tape roll , supply and fixing of following lt supporting accessories with nut bolt & clamps made out as per standard discom's specifications with two coats of red oxide and two coats of aluminium paint etc. as required. all as per pre approved by engineer in-charge.for additional technical parameters of product / work refer annexure "a' attached with this bsr type a lt connector for aerial bunched cable each 73.00

CTN :45063614

30 May, 2026 NA

Bankura - West Bengal

Tender For corrigendum : supply of 25vkoc001 c c - injector connection assly , injector holding flange assly. , pyrometric duct , expansion below , electronic governor-actuator , flex master con for dia 88.9-epdm , compensation sensor for exh.pyrometric duct , disc spring , piston ring , air valve , set of spare gasket & o rings , o ring dia 3 x dia 290 , o ring dia 3 x dia 260 , special seal , set of spares for abb vtc254 turbocharger , spare part kit for fw/sw heat exchanger , pt 100 converter with two threshold , ferquency preamplifier-engine speed , supply board , flash 64k card , communication module , pcmcia card , 16 analog input card , rtd input filed module , filed communication module , fuse 4a gg 10 38 , thermistor protection relay(aux415v ac) , injecting piping assly , set of seal for glacier filter , plug no4 , 25 cts , pyrometric duct bank b , expansion bellow , floating bush(te) , oil seal (190x160x15) , d/row sph rlr brg (100x165x52) , d/row sph rlr brg (120x180x46) , cap screw , portable temperature simulator 0-600 deg celcius , disc spring , release spring , gt2 coalescer filter panel , seal tape roll , barring gear assly - gali , type - gd , loctite 480 , crankcase pressure measurement assly , o ring , drilled cap plug - dn 12 , connecting straub metal grip d42 4 epdm , adjusting screw , injector tappet , gasket , injection pipe , o ring , p2-p4 by pass valve-gachot-dn125 , seal ring chord , expansion bellow , metallic gasket , cartridge , v band clamping , lub oil filling connection , rubber compensator , rubber compensator g0125 x 130 x 016 hks-g nbr gr deb , rubber compensator g0100 x 130 x 016 hks-g nbr gr deb , clamping collar , expansion bellows , metallic joint , o ring an 30 , 21a7 , gasket for lub oilcooler (nopv) , channel plate gasket , engine inlet thermostic valve , o ring , disc spring washer dia.56xdia.28.5x3 , disc spring washer dia.40xdia.21.5x2 , temperature sensor , silencer pads (fx4000) , lid seal for fx4000 , hex bolt , hex bolt , time delay relay(on delay) , elelctrical connnection laptop-engine controller , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , repair kit for gali starter , set of seal for gali starter , solenoid valve-24v , main bearing assly , gasket , gasket , o ring , gasket , seal , impeller , 2 lips oil seal , bearing , mechanical seal eagle , o ring , bearing , cap plug , injector sleeve , o rind- ms 29513/238 , v 75 e , o ring - kalrez , inlet valve guide , gasket exhaust manifod , valve seat metallic ring , inlet valve , exhaust valve , rocker arm bush , metallic joint , rocker cover screw , piston ring - top - chrome , ceramique , piston ring - compression-g3-chrome , piston , gasket , set of gasket for hyd. motor , connecting axiflex metal gripd168.3 , epdm , gasket , service tool kit for oil mist detector , exhaust temperature sensor , o ring - ms29513/230 , 60c7 , o ring an26 , 60c7 , nozzle assly -9 x 0.52 x 148 , helicoflex joint hn100 , d17.4 1.8mm , sea water pump , joint type c with limiter , metallic joint , tc speed sensor , gasket rc , o ring d54 , 50x3 v70d , o ring an29 , 21a7 , gasket , hose , metallic joint , set of spares for air valve and actuator , set of spares for p2/p4 bypass valve , actuator service kit , fresh water temp sensor (rtd) , coupling assly cw , connecting cable (unitel way) , analog input field module type 170aaio3000+slave 170fnt11001 , lamp , hooter (electronic) , power switch , fuse 10x38 2a gg , pt 100 converter with two threshold , solenoid valve-safety stop , power fuse , 32a , rsp bearing safety card , icm safety stop card (4 channel) , frequency preamplifier (engine speed) , human machine interface , main bearing temp probe , connecting rod bearing temp probe , washer bsf , ring for casing , bushing

Central Government/Public Sector

CTN :43070262

14 May, 2026 45.01 Lacs

Mumbai - Maharashtra

Tender For bid to ras repair, maintenance, and installation of plant/ systems/equipments (version 2); contract for network arc of trombay unit- 1 12 core single mode outdoor fibre optic cable of 9/125 micron specification, make:, link/ digilink/ molex/ tyco /amp/ systimax/ r&m/ panduit/ rit or equivalent, mtr 3000, 2 24 core single mode outdoor fibre optic cable of 9/125 micron specification, make:, link/ digilink/ molex/ tyco /amp/ systimax/ r&m/ panduit/ rit or equivalent, no 2000, 3 lc-sc single mode 9/125 duplex fibre patch cord of minimum 2 meter length, make:, dlink/ digilink/molex/tyco/amp/systimax/r&m/panduit or equivalent, no 50, 4 utp cat 5e cable ( 300 meter box), make: dlink/ digilink/ tyco/ amp/ systimax/, r&m/panduit/rit or equivalent, no 70, 5 modular type cat 5e wall mount information outlet with one rj 45 port and box,, make: dlink/digilink/tyco/ amp/systimax/ r&m/ panduit /rit or equivalent, no 1000, 6 cat 5e rj 45 jacks (1 box of 100 nos. connectors), make: dlink/digilink /molex/tyco, /amp/ systimax/ r&m/ panduit/rit or equivalent, no 50, 7 utp cat 6 cable ( 300 meter box), make: dlink/digilink /molex/tyco /amp /systimax/, r&m/panduit/rit or equivalent, no 20, 8 1 inch pvc casing caping 1 conduit, t -joint accessories, couplers etc. for fixing, isi, make, mtr 1000, 9 6 u wall mount rack with fans & power adapter strip, front & both side door, openings, make: valrack/netrack/srlink or equivalent, no 10, 10 9 u wall mount rack with fans & power adapter strip, front & both side door, openings, make: valrack/netrack/srlink or equivalent, no 10, 11 outdoor water proof underground enclosure box for ofc splicing of 24 core splicing,, make: raycaum / mx or equivalent, no 100, 12 wifi extender repeater signal booster, 300mbps make: dlink or equivalent no 20, sr item description in supply uom estimated, qty, 13 underground digging 2 feet deep in soft soil, backfilling for restoration to original, state, mtr 4000, 14 underground digging 2 feet deep in hard soil, & backfilling for restoration to original, state, mtr 1000, 15 underground digging 2 feet deep in tar road & backfilling for restoration to original, state, mtr 500, 16 underground digging 2 feet deep in concrete & backfilling for restoration to original, state, mtr 500, 17 pulling of fo cables inside duct and laying in underground trench mtr 5000, 18 pulling of fo cables inside casing caping / conduits and saddling inside building mtr 3000, 19 pulling of utp cables inside duct and laying in underground trench mtr 2000, 20 pulling of utp cables inside casing caping / conduits and saddling inside building mtr 15000, 21 pulling of fo cables / utp cables inside duct and laying on existing cable tray of 15, feet hight from ground using scaffolding / articulate booms, mtr 3000, 22 termination of utp cat 5/6 cable in rj45 information outlet (i/o) / jacks, fixing of i/o, box on wall, no 2000, 23 otdr testing for fo cable core no 1000, 24 splicing of sm / mm fo cable cores in liu / enclosure box & dressing no 5000, 25 installation / mounting of 6u / 9u rack on wall no 25, 26 one no onsite manpower qtr 12.

Central Government And Public Sector

CTN :44978594

02 May, 2026 7.30 Lacs

Bhandara - Maharashtra

Tender For restoration , repair and maintenance of existing cable duct including raising/lowering of neck of manhole / handhole in bhandara city ( phase-i) , fy 2025-26

Central Government/Public Sector

CTN :44887980

06 May, 2026 NA

Chandipur - Odisha

Tender For repair maint to foot path, hard standing , chequered tiles path, cable duct ,certain painting and certain other works under age br-i, chandipur

State Government

CTN :44835922

06 May, 2026 NA

Munger - Bihar

Tender For supply of heating element with required accessories if any , supply of temperature controller , supply of ceramic blanket with accessories , supply of ceramic rope , supply of ss fabricated flue duct with accessories , supply of stainless steel rod 310 grade for fabrication of hearth , supply of heating element brick , supply of refrctory castable for rectification of refrctory work , supply of refrctory insulation morter for refrctory work , dismantling cleaning, overhaling, including supply of damage part replacement/ repairing of door mechanism , dismantling cleaning, overhaling, including supply of damage part replacement/ repairing of blowers , furnace, trolley, panel, blowers painting work , supply of thermocouple and compensating cable , dismantling cleaning, overhaling & erection charge , reparing of chimeny including intenal & external and repair , supply of 7.5 hp, 415 volt make abв ltd., 2800 rpm/crompton m.s. body & runner s.s motor drive exhaust blower

Cable Tray Repair Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government/Public Sector

Central Government/Public Sector

Central Government And Public Sector

Central Government/Public Sector

State Government