Tender For supply of training rope,fig 11 iron sheet,bamboo for fixing of target,fig 11 target paper,nra target paper,nra target paper,nra target wooden frame,camo net pole,bamboo
Tender For supply of target paper 1x1 , target paper fig 11 , target paper 4x4 , bamboo 10 ft , wooden balli 12ft , iron nails 5 kg , iron nail all type , iron board , sand bag , iron board 10 x 2 , bulb 100w , gun tacker machine , light regulator , flex banner with frame , gun tacker pin , beacon light , pasting paper , gum bottle 700gm , wooden fantti , black paint , white paint , iron case collector , target sheet size 6x4 ft , stop watch , whistle , light box with holder
Tender For supply of wooden target 8x8 , wooden target 4x4 , wooden target 1x1 , combat targer figure 11 , combat target figure 12 , target paper figure 11 , target paper figure 12 , target paper 1x1 , mmg zerogin target paper , hessian cloth for targer paper , repair patch book , white cloth for targer paper screen size 4x4 , red cloth for target screen size 8x8 , sand bag , brush hard iron wired , soft brush , small lithium battery 1.5v , lime stone powder
Tender For purchase of equipments ( s.no 1 to s.no 5 ) for ece department - purchase of equipments, dso (digital storage oscilloscope) bandwidth: 50 100 mhz. sampling rate: 1 gs/s. channels: 2 (minimum). power supply: 100 240 v ac, 50 60 hz. automatic measurements: vpp, vavg, vrms, frequency, period, vmax, vmin, rise time, fall time, +width, width, +duty, duty, etc. horizontal scale: 5 ns/div 50 s/div or equivalent. vertical resolution: 8 bits (2 channelssimultaneously). vertical sensitivity: 1 mv/div 10 v/div (at input). waveform math: +, , , , invert, fft, etc. waveform storage: 16 waveforms or equivalent. communication interface: usb host and usb interface. display: 7-inch color display or equivalent. input impedance: 1 m 2% || 20 pf. accessories: 2 passive probes (1x/10x), 8051 micro controller kit operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., embedded trainer kit (using lpc 2148) cpu - lpc2148, core - 16/32 bit arm7tdmi-s speed - max 60 mhz, flash - 512kb, ram (on-chip) 40kb, 46 general purpose i/opins, usb2.0 one 10bit a/d converter with 14 analog inputs, one 10bit d/a converter, six pwm & watchdog two uarts (16c550), two i2c (400kb/s), two spi eight bit digital output, eight bit digital input,16x2 characters lcd and 4x4 matrixkeypad one potentiometer for giving analog input, relay& buzzer interface i2c devices: rtc, eeprom and seven segment display, on board stepper motordriver lm35 temperature sensor, one rs 232 lines are terminated at 9 pin d type connector and usb interface board has inbuilt power supply and mounted in sturdy cabinet accessories usb cable with utility software to download programs from pc to target board power cord, user manual, strain guage trainer kit ac mains power supply: 230 v 10%, 50 hz metal foil strain gauge mounted on beam/cantilever. strain measurement under applied load. wheatstone bridge arrangement. signal conditioning and amplification circuit. instrumentation amplifiers with 3 digit display for strain / output voltage. zero and gain adjustment controls. provision for applying calibrated loads. table-top trainer with labelled panel. test points for signal measurement. built-in dc power supplies and wooden closed cabinet. supplied with patch cords and user manual., sim reader trainer kitpower supply: operates on 230 v ac 10%, 50 hz mains supply. built-in regulated smps power supply. operating dc supply: 5 v / 12 v with overload and short-circuit protection. sim card interface: supports gsm sim cards compatible with 2g /3g / 4g / 5g networks. sim card read/write interface. supports sim card initialization, authentication,and communication functions. compatible with standard 6-pin / 8-pin sim cardsockets.communication interface: usb 2.0 interface for pc communication. rs-232 serial communication interface. uart communication facility for embeddedsystem interfacing. sim operating parameters: selectable sim clock frequencies: 3.579 mhz 7.159 mhz 14.318 mhz sim supply voltage selection facility. sim reset and activation control.supported protocols and standards: gsm etsi 07.07 and etsi 07.05 at commandsupport. iso/iec 7816 smart card communication support. sim communication command monitoring facility.hardware features: on-board sim card socket. led indication for: power status sim detection reset activity data transmission/reception built-in keypad for standalone operation. lcd display module (128 64) for menu andstatus display. on-board microcontroller-bas
Tender For supply of indoor shooting range - air rifle , air pistol , electronic target system , shooting jacket and trouser , air rifle shoes , air pistol shoes , manual trolley target , cylinder 200 bar , shooting pistol goggles frame , 1.5 ton split ac with installation , acoustic soundproofing , wooden stand for riffle or pistol , rifle ammunition , pistol ammunition