Latest civil infrastructure work Tenders | Government civil infrastructure work Tenders

State Government

CTN :45402451

10 Jun, 2026 NA

Multi City - Punjab

Tender For construction of gabion structures village masol tanda kasauli bhagindi parachh tandi run off control structure and inlet ghaat of pond project village parach water harvesting cum natural recharging structure village masol construction of spurs v

CTN :45048307

30 Jun, 2026 NA

Tarapur - Maharashtra

Tender For corrigendum : : supply, installation, testing & commissioning of electrical equipment for dg block 119a of inrp - ht panels (119a)supply, installation, testing & commissioning of indoor type floor mounted, single front, metal clad, 1250 a, 6.6 kv, 3 phase, 3 wire, vcb switchgear panel suitable for a short circuit current of 31.5 ka for 3 seconds, internally arc tested for 31.5 ka for 1 second, comprising of following incoming & outgoing feeders : incoming feeder: 1 no. 1250 a, 3p vcb outgoing feeders: i) 7 nos. 630 a, 3p vcbii) 1 no. 1250 a, 3p vcb as tie feederwith surge arrestors, relays, pts, cts & other necessary accessories including associated structural steel required for complete installation of the panel & equipment earthing of the panel from both the earthing terminals of the panel to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & drawings. reference drg. nos: ip1/119a/05027339/dwg/001/r0 & ip1/119a/05027339/dwg/002/r0(note: terminal box of each incomer of 6.6kv switchboard shall be suitable for terminating 4x3cx400 sq.mm., 6.35/11kv (e), a2xwy cables.), supply of spares for ht panels as per attached spares list mentiond in section c, part ii of tender, 2.5 mva, 6.6/0.433 kv dry type transformers (119a)supply, installation, testing & commissioning of 6.6/0.433 kv, 2.5 mva, dyn11 dry type cast resin transformer having percentage impedance of 8.5% complete with ht cable end box, lt bus duct flange, off load tap changer on ht side with range of +/-5% in steps of 2.5%, wti scanner, ct for restricted earth fault protection and other necessary accessories including associated structural steel required for complete installation of the transformer & equipment & neutral earthing of the transformer from both the earthing terminals of the transformer to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & drawings.reference drg. no. : ip1/119a/05034347/dwg/001/r0, supply of spares for dry type transformers as per attached spares list mentiond in section c, part ii of tender, 2000 kva diesel generator sets (119a)supply, installation, testing & commissioning of 3 phase 2000 kva prime power 433v, 50hz, 0.8 p.f. diesel-generator sets with 110% overload capacity for 1 hr with four (4) stroke inline or vee type cylinder arrangement having engine speed 1500 rpm, 24v electric battery starting system with a provision of interchangeability of battery bank between two dg sets, complete with all auxiliary equipment including amf control panel, auxiliary mcc panels, heat exchanger cooling system, raw water pump, remote radiator with fans on terrace, ms exhaust piping, exhaust structure (maximum 30 m stack), 4 nos. of 3.6 cubic metre fuel day tank outside dg building (for all 4 dg sets) & 1 no. of 990 ltr intermittent tank inside each dg room, ms "c" class fuel piping between engine & fuel tank, dg room accoustic treatment & complete ventilation of dg room, brushless excitation for alternator, one no. 3200 amp 415 v 4p acb, ms structural steel supports/ channels/ angles & other necessary accessories including associated structural steel required for complete installation of the dg & equipment & neutral earthing of the dg from both the earthing terminals of the dg to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & necessary statutory clearances from cpcb etc. as required and as per tender technical specifications & drawings. design and construction of foundation for exhaust pipe rack/ structure of dg set is included in the scope of the contractor.reference drg. nos. : i) ip1/119a/05034347/dwg/001/r0ii) ip1/119a/05044831/dwg/003/r0iii) ip1/119a/05044831/dwg/004/r0iv) ip1/119a/05044831/dwg/005/r0v) ip1/119a/05044831/dwg/006/r0, supply of sp

State Government

CTN :45352746

12 Jun, 2026 3.31 Lacs

Darjeeling - West Bengal

Tender For civil works to arrest water ingress below the extended part of control room building and arrest further differential settlement of the structure of happy valley 33by11 kv sub-station at darjeeling under darjeeling division, wbsedcl

State Government

CTN :45322414

05 Jun, 2026 59.51 Lacs

Nawanshahr - Punjab

Tender For construction stone masonary water recharging cum silt detention structure in village kukarsuha and crate wire structures in village malewal rouri kukarsuha and run off control structure in village bholewal tehsil balachaur distt. sbs nagar

State Government

CTN :45324925

04 Jun, 2026 10.00 Lacs

Sheopur - Madhya Pradesh

Tender For rate contract for minor civil infrastructure work for all offices zone/sub division /divisions and all 33/11 kv sub station control room situated under onm circle, mpmkvvcl, sheopur.

Central Government And Public Sector

CTN :45326701

17 Jun, 2026 NA

Morigaon - Assam

Tender For tender for selection of vendor for civil infrastructure works towards establishment of a common facility centre in morigaon district, assam, under the pm‑ajay socio‑economic scheme

CTN :45322644

01 Jun, 2026 8.70 Lacs

Sawai Madhopur - Rajasthan

Tender For supply, installation, testing and commissioning of phase wire and street light and vairious electrical equipment needed for implementation of budget announcement 2025-26 - providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket/pole. fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing with uv stabilized pc (uv stablization report submitted for uv cover ) /toughened glass cover and secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm/ wt and potted driver & has a unique bis r number with input voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driver efficiency >85% ,thd(i) 70 and cct 5700k +355k. surge protection shall be min 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs. manufactures word mark/name engraved/embossing on die cast housing to allow traceability/authenticity. fixture shall be as per is 10322 complianced.oem must have its own in, led street light fixture with minimum lumen output 5600 lm, sitc of ip-42 and general construction confirming to is:8623 : 1993, wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as specifications and other parameters required as per point (a) ,(b), (c),(d), (e), (f), (g), (h) as below:-(a)thickness of crca sheet shall be 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / without detachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided(b)complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel. the panel having pe foam/ neoprene rubber gasket of not less than 3mm thickness ,required hardware , concealed hinged door with key type locking arrangement for equipment/switchgear earthed with 2.5 sq.mm braided copper wire.[c) interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 63 amp ) and by solid bus bar (>63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only. all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgear is to be paid extra )(d)wiring between components within switchgear and incoming / outgoing cable shall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap-offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram.(e)all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be point to point (no wire splitting or tee connections) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging.(f)floor mounted panel sh

CTN :45333373

10 Jun, 2026 3.33 Crore

Muzaffarnagar - Uttar Pradesh

Tender For supply of interactive panels with cpu (q2) , professional large format display (v2) (q2) , weighing machine , mill house , fully automatic jaggery production unit , solar panel foundation and all related items , structure of complete plant , bought out for complete plan , erection of mill house and boiling house , hdg set , submersible , fire fighting equipment , hcl kit single , oilfree 15 com , air filter , cylinder c2h2 , regulator c2h2 , hood aas , vacuum hot air oven , digital hot air oven , air circulation fan , microprocessor digital temperature indicator , digital timer , heating mantle , digital muffle furnace , single beam uv , double beam uv , digital photo colorimeter , weighing balance , analytical balance cy , water bath , pid temperature controller , atomic absorption spectrophotometer , gas chromatography , fused silica capillary column , gas purification panel , electromechanical voltage stabilizer , carbon steel cylinder , pressure regulator , glassware , servo candy pillopack wrapping machine , horizontal flow wrapepillopack high speed packaging machine , automatic packing machine , vertical single face paper corrugating machine , corrugated sheet pasting machine , eccentric slotter machine , bar rotary cutting creasing machine , stitching machine , paper reel to sheet cutting machine , flexo graphic printing machine , printing machine , manual jar filling machine , manual pouch sealing machine , manual sticker labelling machine , bag sewing machine , bar coding equipment , bar reader machine , projector , laptop , public address audio system , pantry , desktop with accessorie , tv 45 inch screen , solar panel , bio fertilizer plant , cctv unit for control ) /bid number : gem/2026/b/7564787 * /dated: 26-05-2026 & & / bid document 1 / 42

State Government

CTN :45290474

02 Jun, 2026 NA

Rupnagar - Punjab

Tender For construction of gabion structures village masol tanda kasauli bhagindi parachh tandi run off control structure and inlet ghaat of pond project village parach water harvesting cum natural recharging structure village masol construction of spurs rakoli

CTN :45244477

25 May, 2026 NA

Pondicherry - Pondicherry

Tender For providing and fixing of kitchen chimney gas poipeline connection and kitchen equipments for the canteen building inside the ptu campus under rusa fund - ss dosa plate:supply and fabrication of 4 ft 2.5 ft commercial dosa plate, constructed with ss 304 grade outer body (1.2 mm thick) and heavy-duty ms/cast iron plate (12 mm thick), equipped with 3 4 high-pressure lpg burners with individual control valves,complete with oil drain system, splash guard, sturdy ss frame with adjustable legs, and matt finish, suitable for continuous commercial kitchen use. , ss chapati plate:supply and fabrication of 4 ft 2.5 ft commercial chapati plate, constructed with ss 304 grade outer body (1.2 mm thick) and heavy-duty ms/cast iron plate (12 mm thick), equipped with 3 4 high-pressure lpg burners with individual control valves, complete with oil drain system, splash guard, sturdy ss frame with adjustable legs, and matt finish, suitable for continuous commercial kitchen use., chimney with ducting & blower:supply, fabrication, and installation of 10 feet long commercial kitchen chimney (exhaust hood) made of ss 304 grade (1.0 1.2 mm thickness), rectangular type with ss baffle filters and oil collection tray, connected with 150 sq.ft gi ducting (0.6 0.8 mm thickness), complete with 2 hp heavy-duty centrifugal exhaust blower (3-phase, 1440 rpm), mounted on ms angle support structure, including all necessary fittings, clamps, bends, hangers, and electrical connections, suitable for continuous commercial kitchen operation, bain marie (7 compartment):supply and installation of 7-compartment commercial bain marie unit, fabricated in ss 304 grade (1.0 1.2 mm thickness), complete with 7 nos. gn pans with lids, fitted with 3 kw electric heating element (230v, single phase), thermostatcontrolled water bath heating system, and sturdy ss/ms support structure with adjustable legs, including water tank and drain arrangement, suitable for continuous commercial kitchen and buffet operations., working table with 1 under shelf:supply and fabrication of 4 ft 2 ft working table (vegetable cutter table) made of ss 304 grade (1.0 1.2 mm thickness), complete with one under shelf (u/s), heavy-duty ss square pipe frame, reinforced top with machine mounting provision, and adjustable legs, suitable for vegetable cutting and food preparation in commercial kitchens, gas rice steamer (20 kg):supply and installation of 20 kg capacity gas rice steamer, fabricated in ss 304 grade (1.0 1.2 mm thickness), double-wall insulated type, complete with heavy-duty perforated rice vessel, high-efficiency lpg gas burner, pressure control system, steam outlet, and sturdy ms/ss stand, suitable for continuous commercial kitchen operation., ss rack (4 tier): supply and fabrication of 4-tier stainless steel rack of size 35" 14" 48", made of ss 304 grade (1.0 1.2 mm thickness), complete with four shelves, heavy-duty ss square pipe frame, adjustable legs, and smooth polished finish, suitable for storage of utensils, provisions, and kitchen materials in commercial kitchens., copper gas pipeline:supply, installation, testing, and commissioning of copper gas pipeline system suitable for commercial kitchen, using 3/4 inch main line and 1/2 inch branch lines, complete with all necessary fittings, isolation valves for each equipment, pressure regulator, nrv, and flexible hose connections, properly supported and leak-tested, suitable for lpg gas supply to dosa plate, chapatti plate, rice steamer and gas stove units.

Civil Infrastructure Work Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

State Government

State Government

State Government

Central Government And Public Sector

State Government