Latest clinical thermometer Tenders | Government clinical thermometer Tenders

Central Government/Public Sector

CTN :45393238

22 Jun, 2026 NA

Itarsi - Madhya Pradesh

Tender For supply, installation, testing & commissioning of automatic grease drop point apparatus confirming to astm d566 consisting of electrical heater with digital temperature controland motorized stirrer complete with 400ml beaker, holding cover, metal test cup,glass test tube with teflon cork, clamp formounting the whole assembly on to the column of stand, heater board with 50mm dia. supplied with 1) thermometer range of 0-300 degree-01 nos.,(nabl calibrated). 2) glass beaker-02nos. 3) grease cup-03nos. 4) test tube-03nos. note: 1) the firm with past performance of the tenders/same items subject to submission of proof of duments such as pos/r are only eligible. make: power and electrical co.kolkata or equivalent. [ warranty period: 30 months after the date of delivery ] ]

CTN :45408102

23 Jun, 2026 NA

Mumbai - Maharashtra

Tender For tender for supply of thermometer , temprature sensor fr 98703000034 , transmitter , pressure transmitter , transmitter , sliding distributor fr 98725900001 , a washer 65 , pressure transmitter , o ring , o ring , gasket figure 5 item 33 , micro console card , o ring , nut , gasket , gasket , o ring , snap ring 10x1 , washer , schnorr washer , bearing sleeve , t319 3 sliding rail , bearing shells lines 51 &52 , gasket a 21 x 26 cu b1 , liner o ring , o ring , peel shim , washer , small end bush , cover , washer , receptacle seal for distributor 541 iso 1 , resilient pad vibrachoc e1n 3391 01 , o ring rear bearing of compress pinion shaft , o ring rear bearing of compress pinion shaft , t312 9 h nut m 14 , washer , plug , snp nut h 130 m 16 200 , element 68 78 c ch7 pl 10 29 , back up battery tsx bat m01 , pin , wire sealing and lead for safety locking , fuel make up pump , star filter elelment fr xxbnn151349 , clip dn 113 , lock tab , roller , lower gasket , spring , lock tab , nut , motor compressor cover o ring timing gear side , motor compressor casing o ring , cotter pin m10 20 , o ring shaft assembly , gasket , sealing bush , a gasket 33 x39 , stop washer engine side , lock tab , gasket a 10 15 , handling of cylinder head , lock tab , o ring for diffuser , position switch , tempreture sensor , o ring , gasket , o ring r11 953 954 , bearing shell , sealing ring , o ring , ball joint , ball bearing , lock tab , lock tab , lock tab , lock tab , lock nut , o ring di 30 4 21a7 , e pin 12 30s , seal washer bs c18 20a8 , cetering pin , expansion bellows , gasket , lock tab , gasket 4 holes 120x120x1 2 , shim , o ring , snep nut h130 m10 150 , pin , stop washer , guiding bush , air distributer , rear sleeve bearing , driven feeding pump , gasket , t312 10 h screw m14 60 , t30 11 1 half crown , t307 1 cap , o ring r14 952 953 , sealing ring , o ring , gasket , ball joint , bush , gasket 951 953 , o ring r35 953 954 , temperature sensor , broach assembly gasket , lock tab , lock tab , lock tab , o ring , clutch gasket , ring ch7 pl5 83 , top ring , gasket kit , gasket , gasket , filtering element , t307 3 driving dog , expansion bellows , air filter , scraper ring , compressor front bearing labyrinth gasket , lock nut , stop pin , exhaust valve fr xxbnn151341 , o ring fr xxbnn151345 , o ring fr xxbnn151342 , injection pipe fr xxbnn151349 , injection pipe fr xxbnn151349 , injection pipe fr xxbnn151349 , injection pipe fr xxbnn151349 , injection pipe fr xxbnn151349 , injection pipe fr xxbnn151349 , injection pipe fr xxbnn151349 , injection pipe fr xxbnn151349 , injection pipe fr xxbnn151349 , injection pipe fr xxbnn151349 , injection pipe fr xxbnn151349 , tools for cyl head fr xxbnk151342 , combustion chamber cock fr xxbnn151341

CTN :45404122

09 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using driving and dr

CTN :45404144

09 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for electronics and communication engineering department - supply of equipment for electronics and cmmunication engineering department, 8051 micro controller kit :specification : operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., temperaturemeasurementkitspecification : sensors:rtd (pt-100), thermocouple (fe-k/j-type), and/orthermistor (ntc). display: 3 digit led/lcd digital display(typically 200 mv fsd). temperature source: portable water kettle orheater block. signal conditioning: on-board circuitry foramplification, linearization, and cold junctioncompensation. test points: multiple 2 mm / 4 mm banana socketsfor monitoring input/output signals. power supply: 230 v ac, 50 hz, single-phase. accessories: glass thermometer, 10 k ntcthermistor probe, k-type thermocouple probe,patch cords and user manual., ask modulationanddemodulation kit:specification : message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz,amplitude 5 v. modulator type: switching modulator using analogswitch / transistor switching ic. demodulator: envelope detector and lpf. comparator: lm311 based. supply voltage (board): +12 v, +5 v dc. supply current: 100 ma minimum. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., dth trainer kit:specification :power supply: 200 v to 240 v ac, 50 hz.dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter): input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency:tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m.controls: channel selection. volume control.fault simulation: five built-in simulated faults for troubleshootingexperiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption.pcb size: 15" 12" with multicolour section-wise blockdiagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna.additional features: dth subscription connection withdoordarshanfree channels. free-to-air channel demonstration., fpga trainer kit:specification : must use industry-standard mid-range fpgadevice usb-jtag programmable, compatible withvivado ise (webpack). power supply: 5 v dc through usb or externaladapter. on-board peripherals: leds, switches, pushbuttons, 7-segment display,clock source, gpio /pmod expansion ports, uart, vga / hdmi, usbuartbridge, usb cable. user manual.

CTN :45386611

15 Jun, 2026 NA

Tuticorin - Tamil Nadu

Tender For purchase of lab equipments for basic eng dept - purchase of lab equipments for baisc eng dept (physics and chemistry), digital balance itemcode: a001 weight 500g, accuracy 0.01g, top pan. tare function, caliberation- automatic external display type: led., joule s calorimeter itemcode: a005specifications:copper vessel, battery eliminator 3a, (2,4,6,8,10,12 v), tubular rheostat 20-3.3a, one way plug key, analog type dc ammeter (0 2a), voltmeter (0-5v), thermometer (alcohol), stop clock, ic regulated battery eliminator itemcode: a011specifications:ic regulated, input: 230v ac; output: 0-12v dc in steps of 2v; capacity: 1a or 2a., galvanometer itemcode: a012specifications:moving coil type, 30-0-30 scale, unbranded with bhel specification-sensitivitysensitivity, voltmeter itemcode: a013specifications:dc voltmeter; range 0 10 v, analog., ammeter itemcode: a014specifications:dc (0 - 2 amp), decade resistance box itemcode: a016specifications:resistance box 12 month warranty (dial type) -manganin coil- 2 dials, sonometer apparatus itemcode: a017specifications:sonometer with meter scale attached along with knife edge, tuning forks set 256, 384, 512 ranges, hammer, slotted weight - 500 gm each to a total of 3 kg. brass wire (5 m), travelling microscope itemcode: a018specifications:branded travelling microscope 0 200 mm horizontal and 0-150 mm vertical measurement, potentiometeritemcode: a019specifications:it features a 1-meter to 10-meter constantan/manganin wire stretched on a wooden or sunmica baseboard with a millimeter scale. it includes 4mm brass terminals, a pencil jockey for contact, wire options (10 wires), and a typical resistance range of 10-20 ohms, ideal for high-precision voltage measurements., rheostat itemcode: a021specifications:high-grade ceramic tube, oxidized resistance wire, 0.5a 5a, range 10 100 ., deflection magnetometer apparatusitemcode: a022specifications:deflection magnetometer apparatus with compass box and two short bar magnets, digital electronic balance /analytical balanceitemcode: a001/a007specifictions:load capacity: minimum,500 g readability: 0.01 g,linearity: 0.02g,display: lcd/led,tare function: required,top pan typepower supply: 220 240 v,ac, 50 hz, digital tds meter itemcode: a002specifictions:measuring range: 0 9990,ppm resolution: 1 ppm,display: lcdautomatic temperaturecompensation (atc): requiredwaterproof: minimum ip67 protectionpower source: battery, operated (button cell/aaa, digital ph meter benchtop model itemcode: a003specifications:ph type microprocessor/microcontrolle r ph range: 0 14resolution: 0.01 ph,accuracy: 0.05 ph or better combined ph electrode with temperature sensor two or three-point calibrationfacility temperature compensation type automatic display: lcdpower supply: 220 240 v ac, 50 hz warranty minimum 1 year, laboratory heating mantle (knitted glass yarn) itemcode: a004specifications:capacity: 500ml,temperature range: ambient to 350 c energy regulator/control knob:required power supply: 220-240 v ac,50 hz, mortar with pestle itemcode: a006specifications:material: porcelain size: 100 150 mm inner diameter exterior: glazed grinding surface: unglazed, hot plate itemcode: a008specifcations:top plate material: cast iron plate size: minimum 8 inchdiameter power rating: 2000 w temperature range: ambient o 200 c minimum thermostatic temperaturecontrol: required power supply: 220 240 v ac, 50hz., electric bunsen burner itemcode: a009specifications:electrically operated energy regulator/ control knoboperating temperature 800 c body: stainless steel power supply source: corded electric, supplied with a heavy-duty, heat-resistant,earth-grounded, 3-pin power cord (minimum length 1.2 meters). power consumption: between 350 and 500w power supply: 220 -240 v ac, 50 hz, water distillation unit itemcode: a010specifications:output capacity: 4 litres per hour (lph) ph value: 5.5 to 7.0conductivity (raw water distillation):3.0 4.0 s/cm or less glassware material:borosilicate 3.3 glass (pyrex/duran

CTN :45386617

06 Jun, 2026 NA

Vellore - Tamil Nadu

Tender For ece lab items dept use - eliminator transformer (step-down) kitinput - 220v - 240v ac, 50 hz, output-2v to 12v dc, 0-2 a ripple: 5mv, strain gauge trainer kitmetal foil strain gauge mounted on beam/cantilever strain measurement under applied load wheatstone bridge arrangementsignal conditioning and amplification circuitinstrumentation amplifiers, 3 digit display of strain / output voltage zero and gain adjustment controlsprovision for applying calibrated loads regulated power supply, 230 v ac, 50 hz table-top trainer with labeled paneltest points to measure the signalsbuilt in power supplies and wooden closed cabinet supplied with patch cords and experiment manual, temperature measurement kitsensors: rtd (pt-100), thermocouple (fe-k/j-type), and/or thermistor (ntc).display: 3 digit led/lcd digital display (typically 200mv fsd). temperature source: portable water kettle or heater block.signal conditioning: on-board circuitry for amplification, linearization, and cold junction compensation.test points: multiple 2mm/4mm banana sockets for monitoring input/output signals.power supply: 230v ac, 50hz, single-phase.accessories: includes a glass thermometer, ntc thermistor probe 10k, k-type thermocouple probe, patch cords, and instruction manual., sim reader trainer kitsim compatibility supports 2g 3g 4g lte sim cards,sim reader mode: reading writing gsm sim card data, imsi, ki codes, phonebook interface usb 2.0 or rs 232 serial port for pc communication.clock frequencies: selectable frequencies 3.579 mhz, 7.159 mhz, 14.318 mhz for sim card operation.power supply: onboard smps 12v 2a or 5v dc with overload protection. hardware components:6-pin or 8 pin sim card socket.led indicators for power, sim reset, and data activity.optional lcd 128x64 and keypad 20 keys for standalone operation. software tools support for at commands gsm etsi 07.0707.05, sim manager utilities, and data logger functionality. common trainer kit featuresfault simulation ability to create faults e.g., sim not detected, vcc failure for troubleshooting.test points: multiple test points e.g., 55 nos for observing signals sim rst, clk, i o via oscilloscope.construction tested glass epoxy pcb, often housed in a study educational case., dual output regulated dc variable power supplydual output regulated power supply- input voltage: 230v/50hzac- output voltage: (0 30v)dc- output current: (0 2a)dc- protection circuit: over voltage and over current protection, short-circuit protection- high efficiency: greater than 85%- low ripple and noise: less than 50 mv, lvdt sensor trainer kitac mains power supply : 230v 10%, 50hzfixed regulated dc power supply : +5v, 12v 500matransducer : lvdtlvdt displacement : 20mm (40mm total)displacement scale : linear 20mmdisplacement display (mm) : red color 3 digit led displayexcitation frequency : 4khzexcitation voltage : ac variable 5v, dc digital voltmeter - 3 digit led/lcd display, measurement range: 0 20 v dc, accuracy: class 0.5( 0.5 % full-scale), dc ammeter digital - 3 digit led/lcd display, measurement range: 0 5 a dc, accuracy: class 0.5 ( 0.5 % full-scale)

CTN :45373903

03 Jun, 2026 NA

Daman - Gujarat

Tender For purchase of instruments/equipment s blood pressure monitor led instrument manual (mercury free), digital thermometer for refrigerator measures the refrigerator or freezer temperature from -50 to 70c, includes a one-meter fridge sensor cord accuracy of +/-1c over the full range, ilr alcoholic thermometer (-30 c to + 50 c) coloured alcohol in glass column noncorrodible plastics or metal case. the glass column must be protected against breakage and strongly supported so that the column cannot be displaced more than 0.5 mm vertically with respect to the scale, easy to hang, stature meter 200cm wall mounted, material: plastic, metal band

Central Government / Public Sector

CTN :45395496

18 Jun, 2026 NA

Tirupati - Andhra Pradesh

Tender For supply of crs_surgical_phno.:40683_ digital clinical thermometer[quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted: max 8 lacs ] ]

Central Government/Public Sector

CTN :45396197

11 Jun, 2026 NA

Bengaluru - Karnataka

Tender For supply of sensitive temperature sticker irreversible range from 77 degree to 127 degree celsius 10 label sticker equivalent to model 10 b level of make thermax, rs pro, paper thermometer. ]

Central Government/Public Sector

CTN :45396633

24 Jun, 2026 NA

Mumbai - Maharashtra

Tender For supply of thermometer sensor (oil temperature indicator) ,make bhel or jumo make ( part no 608520/2380) suitable for 1578 kva transformer fitted in 3 phase bhel ac emu rake. [ warranty period: 30 months after the date of delivery ] ]

Clinical Thermometer Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government / Public Sector

Central Government/Public Sector

Central Government/Public Sector