Latest coal grinding mill spares Tenders | Government coal grinding mill spares Tenders

Central Government/Public Sector

CTN :45205510

11 Jun, 2026 NA

Raipur - Chhattisgarh

Tender For corrigendum : procurement of grinding roll and wear parts for stage-2 pulverisers of - grinding roll,hp-1103,63", bull ring assy,coal mill,hp-1103, grinding roll,hp-1103,63", bull ring assy,coal mill,hp-1103

Co-operative

CTN :45415201

10 Jun, 2026 NA

Udhamsign Nagar - Uttarakhand

Tender For fabrication and erection -replacement of the 2" x 2" square bar rails installed on the cane unloader. removal of the old juice gutter from 'a' mill, fabrication and installation of a new one, and conducting a successful trial run. removal of the old m.s. juice tray from 'a' mill, and fabrication and installation of a new one using m.s. plates. fabrication and installation of a new gear guard in the 'a' mill house. welding of worn-out teeth on the mill pinion as required, followed by grinding to a smooth finish. repair of damaged/worn parts of the tail bar coupling by welding as required, followed by grinding. repair of damaged/worn parts of the tail bar by welding as required, followed by grinding. comprehensive repair of the d.s.m. screen: cutting out and removing corroded sections, fabricating and fitting new replacements, repairing all internal piping, and conducting a successful trial run. thorough cleaning of the cane carrier slats, along with their attached links, pins, rollers, and bushes; followed by greasing and refitting said components into the slats in their proper positions. thorough cleaning of the slats, links, pins, bushes, and rollers of the primary/secondary cane carrier chains; followed by greasing, assembling the chain components, and preparing the chain as per instructions. fabrication and installation of juice rings for the rollers. fabrication and installation of mill bearing guards using 3 mm plates. fabrication and installation of m.s. scrapers for the under-feed rollers. cutting of chevron grooves into old mill rollers as required. cutting of chevron grooves into new mill rollers as required. creating 'dots' on the top and feed rollers of the mill using arc-welding electrodes, as per instructions. [repair/replacement of] m.s. components for the worn-out teeth of the under-feed rollers. cutting out patches from a plate and installing them as new teeth. performing arc welding on the grooves of rollers used in the mills using electrodes, as per instructions. fabricating side juice guards for mill rollers from 3 mm plates, as per instructions. fabricating an under-feed roller for the mill in accordance with the provided drawings. dismantling a damaged or defective juice tank in the mill house; fabricating and installing a new tank in its place, and conducting a trial run. replacing or repairing the damaged sections of a defective juice tank in the mill house. dismantling and replacing the bottom plate of a damaged or defective juice tank in the mill house. cane carrier / bagasse carrier / bagasse elevator / cross bagasse carrier / r.b. c. removal of the cane carrier side plate and installation of a new plate. a. welding or forging the enlarged pin holes in the links of the cane carrier, bagasse carrier, etc., to match the specific pin size. a. removal of broken runners from the cane carrier, inter-carrier, bagasse elevator, return bagasse carrier, or cross bagasse carrier, and installation of new runners in their place. a. removal of old, damaged cane carrier slats and installation of new slats. a. the task of drilling holes in new slats for the cane carrier and inter-carrier. a. straightening and repairing cane carrier slats as required. a. repairing damaged and weakened hoods of the cane chopper, cutter, and fibrizer in accordance with instructions. a. removal of old, damaged cane carrier slats; straightening the damaged slats; cutting out the damaged sections; and repairing them by welding in new or salvaged slat pieces cut to size, thereby restoring the slats to their proper dimensions. a. welding the enlarged holes in the inter-carrier links and re-drilling them to the correct size to match the rivets. a. filling the enlarged holes in old inter-carrier slats by welding, and subsequently re-drilling them to create new holes in accordance with the engineering drawings. a. removal of the damaged band from the inter-carrier clutch shaft, fabricating and installing a new one, and conducting a satisfactory

CTN :45255733

09 Jun, 2026 NA

Parganas - West Bengal

Tender For corrigendum : supply of solid carbide drill to size-10.10mm dia , iscar shred mill cutter dia.100 , circular insert of diameter 16 mm , 7mm solid carbide drill , boring tool holders s20r-sclcl-09 or equivalent , milling insert for cutter dia 12 mm with cr 2 , sq. soulder indexable milling cutter , milling insert for cutter dia 12 mm with cr 0.8 , segmented wheel grinding , boring tool holder s25r pclnr12-32 , holder svjcl 2525 m 16 , holder sir 0020 p 16 , dia 16mm inserted endmill cutter , insert - bdmt 11 t308 er-jt pr 1225 ) /bid number : gem/2026/b/7560851 * /dated: 19-05-2026 & & / bid document 1 / 23

CTN :45384429

12 Jun, 2026 NA

Seoni - Madhya Pradesh

Tender For supply of coal mill grinding rolls and bull ring segment -mill model xrp-1043 make bhel

Central Government/Public Sector

CTN :45063334

04 Jun, 2026 10.00 Lacs

Mumbai - Maharashtra

Tender For corrigendum : supply of mill for grinding cereals and grains

CTN :45357868

13 Jun, 2026 NA

Durgapur - West Bengal

Tender For procurement of grinding rolls and bull ring segment for xrp883 coal mill of unit#7/dpps.

Central Government/Public Sector

CTN :45346322

17 Jun, 2026 6.10 Lacs

Jalandhar - Punjab

Tender For supply of slotting saw cutter size 0.8 by 75 by 25.4 mm , slotting saw cutter size 1.5 by 75 by 25.4 mm , slotting saw cutter size 1.2 by 75 by 25.4 mm , slotting saw cutter size 1 by 75 by 25.4 mm , angular cutter 45 degree both side , angular cutter 60 degree both side , t slot cutter size 6 by 10 by 2 shank by dia by width , t slot cutter size 12 by 28 by 10 shank by dia by width , t slot cutter size 12 by 18 by 8 shank by dia by width , milling vice swable base standard size , end mill cutter 30 mm , tap size 7 by 32 into 56 tpi , die size 7 by 32 into 56 tpi , tap size 6 into 1 mm pitch , tap 4.8 into 32 tpi , ring spanner set stanley set 12 pieces , taparia socket set 8 mm to 32 mm ratchet handle goti set , breeze deluxe 450 mm hand leaver shearing machine b4ds18 , angle grinder bosch 4 inch gws 800 , tong smith 18 inch shandasi , wire cutter 8 inch , holder arc welding machine 800 a , impact screw driver set taparia , digital micrometer mitutoyo 0 to 25 mm , gas welding torch big esab , oxygen gas regulator two stage esab , d a gas regulator two stages , digital multimeter , glue gun 200 watts , screw driver 10 inch taparia two way , screw driver 04 inch taparia two way , die handle 21 mm inner dia , tap handle 08 inch , thread gauge in inches mitutoyo , thread gauge in millimeter mitutoyo , center drill 01 mm , center drill 1.5 mm , center drill 02 mm , drill bit 4.5 mm , drill bit 5.2 mm , drill bit 5.3 mm , drill bit 5.50 mm , drill bit 03 mm , drill bit 5.7 mm , tap 5 into 0.8 mm pitch , tap 4 into 0.7 mm pitch , die 6 into 1 mm , cardless electric screw driver with r by f function led light and 43 pcs accessories 240 rpm , drill chuck with key and arbor mt 2 shank 1 to 13 mm capacity heavy duty , hss toll bit 1 by 2 into 4 inch , cutting blade 14 inch bosch , cutting blade 04 inch bosch , grinding wheel 04 inch bosch , emery paper no 80 roll , vernier caliper bty 3 v lithium coin , power hacksaw blade 400 into 32 into 1.6 mm , hacksaw blade 24 tpi , hacksaw blade 32 tpi , mini hacksaw blade , file handle plastic , grinding wheel 10 inch rough , grinding wheel 10 inch smooth , diamond dresser grinding wheel , hss tool bit 1 by 2 into 6 inch miranda , hss tool bit 1 into 8 inch miranda , hss tool bit 5 by 16 into 6 inch miranda , hss tool bit 1 by 4 into 4 inch miranda , locktite 495 , lifeboy shop , duco thinner , shalimar normal thinner , squirrel hair mop brush , d battery 1.5 v , white paint 100 gm pack , red paint 100 gm pack , kerosene oil , gas mask , bulb 60 watts , machine cleaning brush 02 inch , painting brush 02 inch , painting bruch 01 inch , emery paper no 220 roll , thinner trisul 01 ltr pack , asian paint white 01 ltr pack , asian paint og 01 ltr pack , asian paint black 01 ltr pack , red oxide primer 01 ltr pack , cotton waste , welding rod no. - 10 esab , gas lighter welding works , illuminator 20 watts , soap hand wash , goggles for grinding machine , total auto darking welding goggle tsp 9403 , gas hose pipe 08 mm wp 15 kg blue , gas hose pipe 08 mm wp 15 kg red , brass brazing rod 1 by 16 inch , plastic container 01 ltrs capacity , file cord wire brush small , pencil cell aa battery , remote cell aaa battery , file flat bastard 12 inch , file flat bastard 10 inch , file flat smooth 10 inch , file half smooth 8 inch , file flat bastard 8 inch , file flat smooth 8 inch , needle file set 12 pcs set , file flat bastard 6 inch , file flat smooth 6 inch , file flat bastard 4 inch , file triangular smooth 6 inch , file half round bastard 8 inch , file round bastard 10 inch , file diamond flat 6 inch , file triangular diamond 6 inch , allen key set 1.5 to 12 mm , lever oil can heavy duty //bid details 2 / 69 lever oil can heavy duty

Central Government/Public Sector

CTN :45098161

03 Jun, 2026 NA

Katipala - Karnataka

Tender For corrigendum : tender for supply of end mill cutter and parting insert for refinery machine shop - 6 mm dia hss end mill cutter , 8 mm dia hss end mill cutter , 10 mm dia hss end mill cutter , 12 mm dia hss end mill cutter , carbide end mill parallel shank 16mm , carbide end mill parallel shank 18mm , carbide end mill parallel shank 20mm , 14 mm dia hss end mill cutter , 16 mm dia hss end mill cutter , 18 mm dia hss end mill cutter , 20 mm dia hss end mill cutter , 22 mm dia hss end mill cutter , 25 mm dia hss end mill cutter , insert cnmg 120408 gc 435 box of 10 pcs , insert266rg 22mm01a450m 1020 1 point 5mm pitch threading insert shank 40 multiply 40 , insert 266rg 22 mm 01 a450 m 1020 2 mm pitch threading shank 40multiply40 , parting insert n123m1 1100 0008 gm h13a sandik , parting insert n123r1 1500 0010 gr2135 sandvik , insert threading 266rg 22 mm 01 a 450 m 1020 , hss parrel shank std series end mill si end mill size 5mm , ag 5 grinding machine model gws 10 1 ag 5 grinding machine mdl gws 10 125 c

State Government

CTN :45228136

03 Jun, 2026 NA

Udhamsign Nagar - Uttarakhand

Tender For service of vacuum filter and supply of its spares and cluster nozzle - vacuum filter spares & service, s.s. screen having 625 holes/sq. inches. (salem make) (minimum weight 1.2 kg. each screen), brass zigzag strips (2 long), rubber hose pipe (2 " x 24"), mud scrapper 5"x10 mm x 6 ply (dunlop make) for 8 x 16 vaccum filter, araldite 1.8 kg. pack, m-seal 1 kg. packing (pidilite make), a) brass end strip, b) s.s. end strip, copper revit round head 5mm x 12mm, copper revit rounf head 5mm x 15mm, copper revit rounf head 5mm x 18mm, soft lead 8 mm wire, brass tube plate for 8x16 vaccum filter, ss electrode (no 12) 2.5 mm thick, roller for mud conveyor belt, ss clamp for binding rubber hose pipe 2 1/4"x24", s s bolt 1/4"x3/4", s.s. channel 16 long, monarch brass nozzles, m s shocket for monarch brass nozzles, junction box (s.s. sheet) from 3mm thick plate heavy duty, s.s. nipple for decking plate (as per sample), s.s. decking plate for 8x16 (as per our site vacuum filter), s. s. binding strip 3/4" x 2-1/4, s. s. pipe 1.5mm thick, size= 1/2 x 46 , s. s. pipe 1.5mm thick, size= 1/2" x 65 , s. s. pipe 1.5mm thick, size= 1/2" x 16.5 , s. s. pipe 1.5mm thick, size= 1/2 x 28 , s. s. pipe 1.5mm thick, size= 3/4 x 7, s. s. pipe 1.5mm thick, size= 3/4 x 6.5, s. s. pipe 1.5mm thick, size= 3/4 x 10, round head s.s. screw " x 3/4", s.s. electrodes (no. 10) thikness 3.15 mm, vacuum filter vacuum disc plate (brass/gun matel) complete set (left & right), s.s. gate valve (screw type) 2 size, s.s. electrodes (no. 8) 4mm size, servicing of vacuum filter, after dismantling of s.s. screens of vacuum filter no. 1, 2 & 3, cleaning of decking plates, conducting hydraulic testing of five way fitting connections and giving satisfactory leak proof trials of same and thereafter refitting of all the dismantled s.s. screens complete in all respect, fitting of new damaged five way fittings (complete with welding etc.) of vacuum filter no. 1, 2 & 3 and thereafter conducting satisfactory leak proof trials. (5 way fitting), replacement of damaged decking plate nipples of vacuum filter no. 1, 2 & 3 and welding with five ways fitting, thereafter conducting satisfactory leak proof trials., replacement of damaged end strips of vacuum filter with new strips complete in all respect and thereafter conducting satisfactory leak proof trials. half filter, replacement of damaged end strips of vacuum filter no. 3 with new strips complete in all respect and thereafter conducting satisfactory leak proof trials. full filter, replacement of damaged brass/s.s. channels (16 ft. lengthl) of vacuum filter with new s.s/ brass channels complete in all respect, replacement of damaged decking plate of vacuum filter with new decking plate complete in all respect., dismantling & fitting both end s.s. tube of filter with vacuum distribution plate in filter and satisfactory trial., grinding of tunion valve plate with bear plate of vacuum filter and sucessful trial at minimum of 450mm of vacuum at junction with rotation of drum., vacuum genration up to 400mm at vacuum disc (including testing of pipe line to be made), keeping in the condition of genration of vacuum at vacuum pump was more then 625mm., repair of 8 point lubricator of vacuum filters (including cost of all un-serviceable parts), 3/8" bsp, non return valve, angle type, working pressure 21 kg./sq.cm. (as per sample), m.s. plug 3/8", m.s. plug 1/2", m.s. tee 3/8", m.s. elbow 3/8", supply of five way clusterwith nozzlefor mill mist colling system (complete in all respect) as per existingscope of workits including five way fitting branch line and nozzle.1- material- thermoplastic equivalent2- guarantee- one full crushing season, spray nozzle for mist cooling system

Central Government/Public Sector

CTN :45197178

20 May, 2026 NA

Rourkela - Odisha

Tender For tools and tackles for plate mill.(16items) comprising of following: - soldering iron,dia:7-10mm,230vac,65w , - drill,pistol,hard plastic body,6mm , - crimping tool,0.5-16mm2 , - plier,crimping,hyd operated,25-400mm2 , - drive socket set,1/4in , - drilling machine,pillar,13mm,1440rpm , - chop/cut off saw,gco 2400j professional , - allen key extra long ball point set , - self adjust wire insul stripper,6mm2 , - grease gun,hand operated,lever type,1kg , - plier,comb side cutting,250mm , - drill bit set,hss,4-6mm,8mm,10mm,masonry , - disc,grinding,size:od:100,id:16,thk:6mm , - cutting wheel/disc,od:105,id:16,th:1.2mm , - tin cutter with spring,size: 10 , - crimping tool,f/cables upto 25mm2 ,

Coal Grinding Mill Spares Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Co-operative

Central Government/Public Sector

Central Government/Public Sector

Central Government/Public Sector

State Government

Central Government/Public Sector