Latest coal mill repair Tenders | Government coal mill repair Tenders

State Government

CTN :45397974

11 Jun, 2026 80.77 Lacs

Kota - Rajasthan

Tender For work of name :- remaining work pkg. no. rj-23-10/srf (rr) / np / 2022-23 distt kota - providing, laying and spreading and compacting specified graded crushed stone in sub-base course including premixing the material at omc in mechanical mixer (pug mill), carriage of mixed material, laying in uniform layers with motor grader, f.e. loader, on a prepared surface and compacting with vibratory compactor to achieve the desired density including all material, labour, machinery, lighting barricading and maintenance of driversion complete. (morth specification clause 401). with all lead & lift, fdkuiqjk rfd;k ls punzsly, total, kilometre stone reinforced cement concrete m15grade kilometre stone of standard design as per irc:8-1980, fixing in position including painting and printing etc ordinary kilometer stone (precast), fdkuiqjk rfd;k ls punzsly, e.mkuk ls guksfr;k, total, kilometre stone reinforced cement concrete m15grade kilometre stone of standard design as per irc:8-1980, fixing in position including painting and printing etc hectometer stone (precast), fdkuiqjk rfd;k ls punzsly, e.mkuk ls guksfr;k, total, providing and erecting typical citizens information board as per approved drawing & specification of mord, made of two ms sheet of 1.6 mm thick each of size 900 mm 750 mm stiffened by angle iron 25 mm 25 mm 3 mm all around the plate and plates fixed on frame of 75 mm dia pipe of 12 swg sheet (vertical post 3050 m with angle holdfasts and horizontal member 900 mm) to be joined by 5 mm thick ms plate at 12 places (65 50 mm) duly embedded in cement concrete m-15 grade of block of 600 mm 600 mm 750 mm size below ground level as per enclosed drawings & as directed by engineering - in-charge. all ms will be stove enameled on both side, lettering, figuring and border will be with ready mixed synthetic enamel paint of superior quality in required shade and colour etc. complete in all respect. all sections of framed post and steel tube will be painted with primer and two coat of epoxy paint as per drawing and as per mord specification., fdkuiqjk rfd;k ls punzsly, e.mkuk ls guksfr;k, total, providing and laying reinforced cement concrete pipes np-3 for culverts including jointing ends and fixing collar with cement mortar 1:2. (morth specification : clause 1000/2900). 300 mm dia, fdkuiqjk rfd;k ls punzsly, e.mkuk ls guksfr;k, total, dry lean cement concrete sub - base. construction of dry lean cement concrete 1:3:6 sub-base over a prepared sub-grade with coarse and fine aggregate conforming to is: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blening to be as per table 600-1, cement content not to be less than 200 kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonne vibratory roller, finishing and curing., fdkuiqjk rfd;k ls punzsly, total, providing and laying un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub-base with 43 grade cement, coarse and fine aggregate conforming to is:383, maximum size of coarse aggregate not exceeding 25mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or fix form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures and vacuum processing pump as approved, curing compound, finishing to lines and grades as per drawing as per morth specification : clause no. 602, 112. using cement concrete m-30 pavement grade, fdkuiqjk rfd;k ls punzsly, total, earthwork in excavation for foundation of structure complete with all lift, dewaterin

Co-operative

CTN :45415201

10 Jun, 2026 NA

Udhamsign Nagar - Uttarakhand

Tender For fabrication and erection -replacement of the 2" x 2" square bar rails installed on the cane unloader. removal of the old juice gutter from 'a' mill, fabrication and installation of a new one, and conducting a successful trial run. removal of the old m.s. juice tray from 'a' mill, and fabrication and installation of a new one using m.s. plates. fabrication and installation of a new gear guard in the 'a' mill house. welding of worn-out teeth on the mill pinion as required, followed by grinding to a smooth finish. repair of damaged/worn parts of the tail bar coupling by welding as required, followed by grinding. repair of damaged/worn parts of the tail bar by welding as required, followed by grinding. comprehensive repair of the d.s.m. screen: cutting out and removing corroded sections, fabricating and fitting new replacements, repairing all internal piping, and conducting a successful trial run. thorough cleaning of the cane carrier slats, along with their attached links, pins, rollers, and bushes; followed by greasing and refitting said components into the slats in their proper positions. thorough cleaning of the slats, links, pins, bushes, and rollers of the primary/secondary cane carrier chains; followed by greasing, assembling the chain components, and preparing the chain as per instructions. fabrication and installation of juice rings for the rollers. fabrication and installation of mill bearing guards using 3 mm plates. fabrication and installation of m.s. scrapers for the under-feed rollers. cutting of chevron grooves into old mill rollers as required. cutting of chevron grooves into new mill rollers as required. creating 'dots' on the top and feed rollers of the mill using arc-welding electrodes, as per instructions. [repair/replacement of] m.s. components for the worn-out teeth of the under-feed rollers. cutting out patches from a plate and installing them as new teeth. performing arc welding on the grooves of rollers used in the mills using electrodes, as per instructions. fabricating side juice guards for mill rollers from 3 mm plates, as per instructions. fabricating an under-feed roller for the mill in accordance with the provided drawings. dismantling a damaged or defective juice tank in the mill house; fabricating and installing a new tank in its place, and conducting a trial run. replacing or repairing the damaged sections of a defective juice tank in the mill house. dismantling and replacing the bottom plate of a damaged or defective juice tank in the mill house. cane carrier / bagasse carrier / bagasse elevator / cross bagasse carrier / r.b. c. removal of the cane carrier side plate and installation of a new plate. a. welding or forging the enlarged pin holes in the links of the cane carrier, bagasse carrier, etc., to match the specific pin size. a. removal of broken runners from the cane carrier, inter-carrier, bagasse elevator, return bagasse carrier, or cross bagasse carrier, and installation of new runners in their place. a. removal of old, damaged cane carrier slats and installation of new slats. a. the task of drilling holes in new slats for the cane carrier and inter-carrier. a. straightening and repairing cane carrier slats as required. a. repairing damaged and weakened hoods of the cane chopper, cutter, and fibrizer in accordance with instructions. a. removal of old, damaged cane carrier slats; straightening the damaged slats; cutting out the damaged sections; and repairing them by welding in new or salvaged slat pieces cut to size, thereby restoring the slats to their proper dimensions. a. welding the enlarged holes in the inter-carrier links and re-drilling them to the correct size to match the rivets. a. filling the enlarged holes in old inter-carrier slats by welding, and subsequently re-drilling them to create new holes in accordance with the engineering drawings. a. removal of the damaged band from the inter-carrier clutch shaft, fabricating and installing a new one, and conducting a satisfactory

State Government

CTN :45402026

23 Jun, 2026 NA

Yamunanagar - Haryana

Tender For supply of coal mill feeder spares - vieweing mirror with whiper (as per sample) , belt tension roller moc: (en-8, forged alloy steel) (as per sample) , seal housing moc: carbon steel 1030 grade (as per sample , head pulley/driving pulley moc: carbon steel (as per sample) , take up pulley with eccentric bearing housing moc: carbon steel , support roller of r/c feeder moc: carbon steel; shaft material en-8 (as per sample) , take up shaft (moc: en8) as per sample ,, bearing housing of connecting plate of head cell of r/c feeder/ moc- aluminium (as per sample) , connecting bushing (with pin) 1 set =10 nos. moc: neoprine rubber with bronz bush (as per sample)

CTN :44395653

09 Jun, 2026 18.99 Lacs

Hyderabad - Telangana

Tender For bid to ras corrigendum : supply of multi deck roller ball mill

CTN :45406850

17 Jun, 2026 NA

Shahjahanpur - Uttar Pradesh

Tender For supply of gm casting c c - rough machined hollow gm bushes , rough machined solid gm bushes , gun metal bearing for transmission gear as per drawing , gun metal bearing for conversion gear , gun metal bearing for mill roller , gun metal bearing on conversion basis for mill roller , gm bearing for trpf of mill , rough machined solid gm bushes on conversion

CTN :45407496

17 Jun, 2026 1.42 Lacs

Sitapur - Uttar Pradesh

Tender For supply of of c. s. bearing housing for feed and discharge roller (on conversion basis) , mill size 30" x60"

CTN :45376338

06 Jun, 2026 NA

Thanjavur - Tamil Nadu

Tender For purchase of mill roller arcing electrode make azucar

CTN :45383133

12 Jun, 2026 1.71 Lacs

Murshidabad - West Bengal

Tender For procurement of air seal housing, roller journal,is-2062 for coal mill zgm123n, stage-1, sgtpp

CTN :45375021

12 Jun, 2026 NA

Tiruvallur - Tamil Nadu

Tender For supply of sugar mill roller grooving tool holder and bit

CTN :45363422

06 Jun, 2026 NA

Thanjavur - Tamil Nadu

Tender For purchase of mill roller bearing lub system spares - spares for mill roller bearing lub system, heavy duty straight connector 1/4 bspt x m16 x 1.5thread (suitable for 8 mm tube), heavy duty elbow connector 1/4 bspt x m 16x1.5 thread, heavy duty elbow connector 1/8 bspt x m 16x1.5 thread (suit for 10 mm tube), r2 parker hose heavy duty m16 x 1.5 survivel nut both end to suit for 8 mm tube

Coal Mill Repair Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

Co-operative

State Government