Latest cold lab chamber Tenders | Government cold lab chamber Tenders

CTN :45404137

16 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For supply of lab equipment for department of electronics and communication engineering - dual output regulated dc variable power supply, function (signal) generator, digital storage oscilloscope, digital ic trainer kit with breadboard, dc voltmeter, dc ammeter, decade resistance box, decade capacitance box, decade inductance box, 8051 microcontroller kit, ask modulator and demodulator trainer kit, dth trainer kit, fiber optic communication demonstration trainer kit, sim reader trainer kit, fpga trainer kit

CTN :45404144

09 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for electronics and communication engineering department - supply of equipment for electronics and cmmunication engineering department, 8051 micro controller kit :specification : operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., temperaturemeasurementkitspecification : sensors:rtd (pt-100), thermocouple (fe-k/j-type), and/orthermistor (ntc). display: 3 digit led/lcd digital display(typically 200 mv fsd). temperature source: portable water kettle orheater block. signal conditioning: on-board circuitry foramplification, linearization, and cold junctioncompensation. test points: multiple 2 mm / 4 mm banana socketsfor monitoring input/output signals. power supply: 230 v ac, 50 hz, single-phase. accessories: glass thermometer, 10 k ntcthermistor probe, k-type thermocouple probe,patch cords and user manual., ask modulationanddemodulation kit:specification : message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz,amplitude 5 v. modulator type: switching modulator using analogswitch / transistor switching ic. demodulator: envelope detector and lpf. comparator: lm311 based. supply voltage (board): +12 v, +5 v dc. supply current: 100 ma minimum. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., dth trainer kit:specification :power supply: 200 v to 240 v ac, 50 hz.dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter): input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency:tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m.controls: channel selection. volume control.fault simulation: five built-in simulated faults for troubleshootingexperiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption.pcb size: 15" 12" with multicolour section-wise blockdiagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna.additional features: dth subscription connection withdoordarshanfree channels. free-to-air channel demonstration., fpga trainer kit:specification : must use industry-standard mid-range fpgadevice usb-jtag programmable, compatible withvivado ise (webpack). power supply: 5 v dc through usb or externaladapter. on-board peripherals: leds, switches, pushbuttons, 7-segment display,clock source, gpio /pmod expansion ports, uart, vga / hdmi, usbuartbridge, usb cable. user manual.

CTN :45384463

08 Jun, 2026 NA

Nagapattinam - Tamil Nadu

Tender For supply of eee dep upgradation & loboratories - eee dep upgradation & loboratories, transformer oil bdv test kit, loading rheostat three phase, single output regulated dc variable power supply, dual output regulated dc variable power supply, function(signal)generator, digital ic trainer kit with breadboard, dc voltmeter, dc ammeter, decade resistance box, decade capacitance box, decade inductance box, 8051 micro controller kit, half wave &full wave rectifier kit

CTN :45365499

04 Jun, 2026 NA

Nagapattinam - Tamil Nadu

Tender For purchase of ece lab equipments for lab upgradation - purchase of ece department equipment, digital ic trainer kit with breadboard, 8051 microcontroller kit and interfacing, lvdt trainer kit, strain gauge trainer kit, temperature measurement kit, decade resistance box, decade capacitance box, decade inductance box, fpga trainer kit, dc voltmeter(digital), embedded trainer kit (using lpc2148), dso (digital storage oscilloscope), dc ammeter

CTN :45375038

15 Jun, 2026 1.49 Lacs

Coimbatore - Tamil Nadu

Tender For supply of lab equipments for ece dept.microelectronics lab. - list of items:supply of lab equipments(for specification details refer notice inviting tender), function (signal) generator (detailed specification enclosed), digital ic trainer kit with breadboard (detailed specification enclosed), moving coil microphone (detailed specification enclosed), lvdt trainer kit (detailed specification enclosed), strain gauge trainer kit (detailed specification enclosed), temperature measurement kit (detailed specification enclosed), fiber optic communication trainer kit power supply (detailed specification enclosed)

CTN :45343672

11 Jun, 2026 NA

Madurai - Tamil Nadu

Tender For purchase of electronics and communication engineering practices (equipment) - equipments for electronics and communication engineering practices:, 8051 micro controller kit operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., embedded trainer kit (using lpc2148) cpu -lpc2148, core -16/32 bit arm7tdmi-s speed -max 60 mhz, flash -512kb, ram (on-chip) 40kb, 46 general purpose i/opins, usb2.0 one 10bit a/d converterwith 14 analog inputs, one 10bit d/a converter, six pwm &watchdog two uarts (16c550), two i2c (400kb/s), two spi eight bit digital output, eight bit digital input,16x2 characters lcd and 4x4 matrixkeypad one potentiometer for giving analog input, relay & buzzer interface i2c devices: rtc, eeprom and seven segment display, on board stepper motordriver lm35 temperature sensor, one rs 232 lines are terminated at 9 pin d type connector and usb interface board has inbuilt power supply and mounted in sturdy cabinet accessories usb cable with utility software to download programs from pc to target board power cord, user manual, ask modulation and demodulation kit message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz, amplitude 5 v. carrier signal: sine wave, frequency 200 khz, amplitude 5 v. modulator type: switching modulator using analog switch / transistor switching ic. demodulator: envelope detector and lpf. comparator: lm311 based. supply voltage (board): +12 v, +5 v dc. supply current: 100 ma minimum. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., dth trainer kitpower supply: 200 v to 240 v ac, 50 hz.dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter):input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency: tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m.controls: channel selection. volume control.fault simulation: five built-in simulated faults for troubleshooting experiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption.pcb size: 15" 12" with multicolour section-wise block diagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna.additional features: dth subscription connection with doordarshanfree channels. free-to-air channel demonstration.

CTN :45326590

10 Jun, 2026 NA

Erode - Tamil Nadu

Tender For ece lab equipments - function generator, digital ic trainer kit, am trainer kit, fm trainer kit, ask, psk, fsk trainer kit, pam, pwm, ppm trainer kit, xilinx/altera/eqvalent fgpa boards, mosfet drain current and transfer characteristics trainer kit, frequency response of cs amplifier trainer kit, class a transformer coupled power amplifier trainer kit, rc phase shift oscilator kit, wien bridge oscillator kit, hartley oscillator kit, colpitts oscillatyor kit, instrumentation amplifier kit, active lowpass, highpass and bandpass filters circuits kit, pll characteristics kit, arm processor kit

CTN :45354788

11 Jun, 2026 NA

Shekhapura - Bihar

Tender For supply of arduino uno microcontroller , breadboard , jumper wires male female , resistors , led red green , capacitors , transistors , diodes , sensors , lcd , relay module , motors , power supply battery , multimeter , soldering kit , project work station , fpga trainer boards , logic analyzer , dual regulated power supply , arduino uno , stm dev board , pic development kit , raspberry pi , digital multimeter , dac trainer board , rtos trainer , soldering stations , lm analog temp sensor , ds digital temp sensor , ptrtd resistance temp detector , k type thermocouple , ir proximity sensor reflective ir , digital ir obstacle sensor , ir flame sensor , ir temperature sensor mlx90614 , mq two lpg smoke , mq three alcohol , mq six lpg butane , mq seven carbon monoxide , mq air quality , pir motion sensor , ultrasonic sensor , accelerometer , gyroscope , solderless breadboard full size , mini breadboard , jumper wires male male , jumper wires male female , jumper wires female female , ic socket eight pin , ic socket fourteen pin , ic socket sixteen pin , solar cell trainer kit , ujt as relaxation oscillator kit , scr characteristics kit , ldr , photo diode , phototransistor , semiconductor temperature coefficient trainer kit , logic gate trainer kit , ic trainer kit , measurement of steady state and transient response of rl rc and rlc circuits , frequency response of twin t notch filter and to study of active filter , study of single phase inverter trainer , to study the behaviour , determine the transient , to study of pid controller for simullatio n process , to study basic electric al trainer , to study single phase transformer , to obtain efficiency of a dc shunt machine , to obtain efficiency and voltage regulation of a single phase transform , to study dc series motor , make connection of dol starter , test the machines required , maxwells bridge trainer kit ) /bid number : gem/2026/b/7582907 * /dated: 27-05-2026 & & / bid document 1 / 44

CTN :45351358

04 Jun, 2026 NA

Pudukkottai - Tamil Nadu

Tender For supply of lab equipments - purchase of lab equipments, ask modulation and demodulation kitspecifications: message signal1: 8-bit variable data,amplitude 5v. message signal 2: debounced data, amplitude low (0) and high (5 v). message signal 3: fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz, amplitude 5 v. carrier signal: sine wave, frequency 200 khz, amplitude 5 v. modulator type: switching modulator using analog switch / transistor switching ic. demodulator: envelope detector and lpf. comparator: lm311 based. supply voltage (board): +12 v, +5 v dc. supply current: 100 ma minimum. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., fiber optic communication trainer kitspecifications:power supply: 230 v ac 10%, 50 hz mains operation. built-in regulated power supply. optical transmitters: led transmitter: 660 nm. optical receivers: phototransistor / pin photodiode receiver. built-in signal conditioning and amplifier circuits. audio power amplifier with speaker/headphone output. comparator / pulse shaping circuit for digital signal recovery. test points for cro observation and signal monitoring. fiber media: multimode plastic optical fiber (pof). fiber patch cords with connectors. signal sources: built-in sine wave generator. built-in square wave / digital pulse generator. voice signal input through built-in microphone/audio source. trainer features: separate transmitter and receiver sections. on-board test points for signal observation. led indicators for signal monitoring. fault simulation facility. compact tabletop modular design. circuit diagram printed on pcb. bandwidth: analog bandwidth: up to 350 khz. digital bandwidth: up to 2.5 mhz. controls: variable signal amplitude control. variable frequency control. optical intensity adjustment. standard accessories: patch cords and connectors. power cord. audio connecting cable. user manual.

CTN :45328819

09 Jun, 2026 NA

Tiruchirappalli - Tamil Nadu

Tender For equipment items - dual output regulated dc variable power supply-input voltage : 230v/50 hz ac.output voltage : (0-30)v dc.output current : (0-2)a.dcprotection circuit : over voltage, over current and short circuit protection.high efficiency : greater than 85 %.low ripple and noise less than 50 mv.digital display, digital ic trainer kit with breadboard:+5v dc, 1 a regulated power supply. 12v dc / 15v dc, 200 ma regulated power supply.solderless breadboard with minimum 840 tie- points, power distribution buses.zif(zero insertion force)ic sockets to accommodated 8 or 16 pin ics.logic input and output leds for output monitoring.16 buffered led outputs.16 debounced switch inputsvariable clock generator: 0.5 hz to 50 hz.single pulse output : 100 ms(buffered,positive and negative outputs).one seven-segment display with 4 bcd inputs.built-in logic switches.manual clock: debounced push-button(one pulse per press)., digital storage oscilloscope-bandwidth: 50-100 mhz. sampling rate: 1gs/sec.channels: 2 (minimum). power supply: 100v 240v ac, 50-60 hz automatic measurement: vpp, vavg,rms, frequency, period, vmax, vmin, rise time, fall time, + width, - width, +duty, - duty etc., horizontal scale: 5 ns/div 50 s/div or equivalent vertical resolution: 8 bits (2 channels simultaneously) vertical sensitivity: 1 mv/div 10 v/div (at input) waveform math: +, -, x , , invert, fft etc., waveform storage: 16 waveforms or equivalentcommunication interface: usb host, usb interface. c 7-inch color display or equivalent input impedance - 1 m 2%, // 20 pf accessories:2 xpassive probes (1x/10x), pcb prototype machine :manual software : copper cam & mach3 mill.resolution (x/y) : 3.125 micrometre.working area(x/y/z) : 200 x 300 x 120 mm.minimum width line and space : 0.1 mm (4 mil).maximum travel speed : 58 mm/sec(2.28 ).drilling range: 0.2 3.175 mm(8-125 mil).maximum drilling cycles : 50 cycles/minmain axle power rating : 300w.main axle rotating speed : 25000 rpm.maximum working speed : 3500 mm/min.feeding height: 120 mm.working drive : 0.02 0.05 mm.repositioning accuracy : 0.01 0.02 mm.supported formats : standard gerber, dxf, excellon.capability of processing various materials:fr4, copper clad, acrylic, metal, aluminium etc.power supply : 230v ac

Cold Lab Chamber Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors