Latest collecting electrode Tenders | Government collecting electrode Tenders

CTN :41023897

21 Jul, 2025 8.40 Lacs

Nellore - Andhra Pradesh

Tender For lifting and re erection of badly damaged and bent collecting electrodes, fabrication and erection of new supporting angles, cleat angles in esp-a pass of any field of unit-1 boiler welding of u guides and carrying of alignment of collecting electrodes to maintain gap between collecting electrodes include all t&p and consumables for during the overhaul 2025-26

State Government

CTN :41003484

23 Jul, 2025 NA

Jharsuguda - Odisha

Tender For supply of supply of esp spares for 210 mw power plant by oem or oes d d - plain bearing , shock bar for esp , emiting electrode , pin wheel big for esp , pin wheel ii small for esp , shock bar guide esp , shaft1 2 hole , shaft2 14 hole , shaft3 14 hole , shaft4 15 hole , sleeve for vertical shaft eerm esp , shim for eerm esp , thrust pad for eerm esp , clutch coupling collecting shaft plus motor , housing for emmiting driveesp , top vertical shaft 1eermesp , middle vertical shaft 2eermesp , bottom verticalshaft 3eermesp , shaft 1 horizontal eerm esp , u clamp for collecting electrode , shock pad , set ring for esp , sleeve for esp , outer arm for collecting , inner arm for collecting , emitting outer arm , thrust bearing for esp , screen tube for espfor esp , collecting electrode 13500cm height , deflection plate , vertical rapping shaft erm 15mtr esp , horizontal rapping shaft erm 15mtr esp , collecting rapping shaft 15mtr esp , cover for emitting rapping shaft , erm shaft insulator housing assembly

CTN :40627357

11 Jul, 2025 NA

Bokaro - Jharkhand

Tender For corrigendum : spares for esp of boiler 9 - butterfly valves, cat. no. 09000116002guide plate u-profile for collecting electrodes, cat. no. 09000116024hammer assembly for crm, cat. no. 09000116025hammer assembly for erm, cat. no. 09000116026hammer assembly for inlet gd rapping machanism, cat. no. 09000116300ci bearing for crm, cat. no. 09000116301ci bearing for erm, cat. no. 09000116302ci bearing for inlet gd rapping mechanism, cat. no. 09000116021shaft complete with sleeve of crm, cat. no. 09000116008shaft (horizontal) complete with sleeve of emitting rapping machanism, cat. no. 09000116011vertical shaft of emitting rapping drive, cat. no. 09000116303shaft end (vertical) of emitting rapping drive, cat. no. 09000116304shaft complete with sleeve of inlet rapping mechanism, cat. no. 09000116305adjusting ring/set ring for rapping shaft, cat. no. 09000116306clutch couplingset for collecting rapping drive, cat. no. 09000116307grip coupling set for inlet gd rapping drive, cat. no. 09000116308grip coupling set for emittingrapping drive, cat. no. 09000116309pin wheel (big+small) for emitting rapping drive, cat. no. 09000116310bottom bearing for emitting rapping drive, cat. no. 09000116311bottom bearing shaft for emitting rapping drive, cat. no. 09000116312bush bearing for emitting rapping drive, cat. no. 09000116313bearing cage of bush for emitting rapping drive, cat. no. 09000116314shock bar for collecting system, cat. no. 09000116013shock anvil with fasreners for collecting rapping, cat. no. 09000116014shock anvil with fasreners for emitting rapping, cat. no. 09000116015shock bar guide for collecting rapping system, cat. no. 09000116315attachment for shock bar guide of collecting rapping system, cat. no. 09000116316clamp for shock bar guide of collecting rapping system, cat. no. 09000116317flat for shock bar guide of collecting rapping system, cat. no. 09000116318inlet gd screen (plate-a), cat. no. 09000116319inlet gd screen (plate-b), cat. no. 09000116320inlet gd screen (plate-c), cat. no. 09000116321guide vane for inlet gd screen (type-1), cat. no. 09000116322guide vane for inlet gd screen (type-1), cat. no. 09000116323guide vane for inlet gd screen (type-1), cat. no. 09000116324geared motor with gear box for emitting rapping mechanism, cat. no. 09000116325geared motor with gear box for collecting rapping mechanism, cat. no. 09000116175gland for emitting rapping drive, cat. no. 09000116176gland for collecting rapping drive, cat. no. 09000116177gland for inlet gd rapping drive, cat. no. 09000116326shim plate for above c.i. bearing, cat. no. 09000116003shim plate (loose) for shock bar

CTN :40697499

16 Jul, 2025 24.70 Lacs

Chhabra - Rajasthan

Tender For corrigendum : supply of spares for esp system of unit#1 to 4, ctpp, chhabra for fy. 2025-26 - inner arm assembly for cerm & eerm consistsi)inner arm half-2 nos.ii)hex bolt m16x90-1 nos.(half threaded, grade 4.6) iii) hex bolt m16x40-1 nos.(half threaded, grade 4.6) iv) hex nuts m16-2 nos.( grade 4.6) (moc en-08 for flats ) as per drawing / sample, outer arm for cerm (total weight 8kg+/-2.5-5%)i)roller wheel- 1 no.ii) arm- 2 nos.(10 mm thick flat)iii)washer- 2 nos.(45x28x3 mm)iv)pin - 2 nos.(l114xdia25mm round bar) as per drawing / sample*moc en-08 for roller wheel & pin and ms for arms & washers, sleeve bearing bracket assy. consistsi)sleeve bearing/ci liner (in two halves),c.i.fg-210 - 2nos.ii)ht hex nut+ bolt m12x50- 2nos.iii)ms strip (40x40x10)- 4 nos.iv)weld type - 6 (moc for liner set is as per is-210 fg-210) as per drawing / sample, set ring (material en-08)id-50+/-0.5mm , od-75.0m, height-18.00mm grub screw,m10x15 mm-2nos., grip coupling for eerm (moc en-08 for flat) consistsgrub screw m10x25 mm -1 no.as per drawing / sample, shaft sleeve 50 mm (en-24)inner dia -50+/- 0.5 mmouter dia-70+/- 0.5 mmlength- 130+/-1 mm thickness-10 mm,, shaft sleeve 40.5 mm (en-24)inner dia -40+/- 0.5 mmouter dia-50+/- 0.5 mmlength- 120+/-1 mm thickness-5 mm, plain bearing assembly for rapping mechanism consistsi)lower half -01(is-210-fg 200)ii) upper half -01 01(is-210-fg 200)iii)hex bolt m16x120 mm-02 nos (4.6 grade half threded)iv)hex nut m16 -02 nos.( 4.6 grade)*casting must be free of all kinds of casting defects., top sleeve for emmiting shaft dia.40 mm (material en-8), end shaft for cermdia 50mmlenth : 790mmhole dia 17mmmaterial : en-8 as per drawing / sample, gd screen material as per is 513,crca sheet 2.5mm (as per drawing),material of hook ms, 4.00mm thick, emitting rapping shaft i, emitting rapping shaft ii, emitting rapping shaft iii, c.i. liner in two halves (moc as per is 210 fg 210), shock bar guide angle, u-guide/clamp for collecting electrodes, material - cold rolled ms sheet is 513, 2.50 mm thick or as per drawing/sample, screen tube for emmitting drives of esp, material - ms sheet 5.00 mm thick or as per drawing/sample, item should be painted with red oxide inner/outer side

CTN :40893784

15 Jul, 2025 NA

Multi City - Andhra Pradesh

Tender For procurement of esp spares for the year 2025-26 - esp collecting gear box first stage,worm,gear,type:helical , outer arms for emitting electrodes , outer arm for collecting electrode rapper , inner arm with 2 bolt+2 nuts for , plain bearing assembly (plain , clutch; , coupling for cerm gear box suitable for pbl make cerm gear box model no.

CTN :40899473

21 Jul, 2025 91.67 Lacs

Kota - Rajasthan

Tender For tn-11174 supply of spares for esp of unit 1 to 7 at kstps, kota. - outer arm for emitting rapping sys., outer arm for collecting rapping, inner arm of esp for collecting, u" guide for collecting electrodes with inner distance 44.5 mm for stage- 1 to 2, u" guide for collecting electrodes with inner distance 54.0 mm for stage- 3 to 5, spiral emitting electrode 47 turns, wire, 2.7mm (mat for wire uhb-904 l, mat for hook- tube carbon steel), emitting electrode 2.7 mm wire dia, 52 turns spiral type with hook (material for wire uhb-904 l, material for hook tube carbon steel), sleeve for shock bar of esp with ht bolt & nut (m 20x75), sleeve bearing for emitting drive, set ring for cerm, plain bearing, shaft insulator, g d screen sheet, pin for pin wheel i/ii, shaft-i for cerm d50, l-4790mm, shaft-ii for cerm d50, l-4985mm, emitting rapping shaft 40mm dia, 2500mm length, shaft-iii for eerm d50 l-3350mm, emitting drive shaft for stage 3, dia-40mm, l-3306mm, key size 12x8x70, emitting drive shaft iii, dia-40mm, l-2995mm, ms packing shim, 100 mm x 70 mm, thickness 6mm, pin wheel-i (big), pin wheel-ii (small), shock pad for shock bar for esp, shaft sleeve, od 50mm,id 40.5 mm,length 120mm, shaft-i for eerm, d-50 mm, l-4320 mm stage-ii, shaft-ii for eerm, d-50 mm, l-4250 mm stage-ii, emitting drive shaft -ii, d-40 mm, l-3020 mm stage- ii, end shaft for cerm with key slots, d-50 mm, l-790 mm stage-iii to v, shaft-i for eerm, d-50 mm, l- 3120 mm stage iii to v, shaft-ii for eerm, d-50 mm, l- 3290 mm stage iii to v, top coupling for emitting drive shaft-i , d- 40 mm, shock bar guide (f) for stg.-i , 6 slot, shock bar guide (r) for stg.-i , 4 slot, shock bar guide (r) for stg.-ii , 4 slot, deflection plate ms having size 495x230x2.5mm as per drwing enclosed

corporations/Associations/Others

CTN :40901749

21 Jul, 2025 NA

Cuddalore - Tamil Nadu

Tender For supply of outer arm for eerm stage-i as per drg. enclosed , outer arm -cerm , inner arm assy , plain bearing (rapping mechanism for collecting electrodes) - materials c. i. - 210 fg150 as per drawing

Collecting Electrode Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

corporations/Associations/Others