Latest communication item Tenders | Government communication item Tenders

CTN :45404144

09 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for electronics and communication engineering department - supply of equipment for electronics and cmmunication engineering department, 8051 micro controller kit :specification : operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., temperaturemeasurementkitspecification : sensors:rtd (pt-100), thermocouple (fe-k/j-type), and/orthermistor (ntc). display: 3 digit led/lcd digital display(typically 200 mv fsd). temperature source: portable water kettle orheater block. signal conditioning: on-board circuitry foramplification, linearization, and cold junctioncompensation. test points: multiple 2 mm / 4 mm banana socketsfor monitoring input/output signals. power supply: 230 v ac, 50 hz, single-phase. accessories: glass thermometer, 10 k ntcthermistor probe, k-type thermocouple probe,patch cords and user manual., ask modulationanddemodulation kit:specification : message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz,amplitude 5 v. modulator type: switching modulator using analogswitch / transistor switching ic. demodulator: envelope detector and lpf. comparator: lm311 based. supply voltage (board): +12 v, +5 v dc. supply current: 100 ma minimum. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., dth trainer kit:specification :power supply: 200 v to 240 v ac, 50 hz.dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter): input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency:tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m.controls: channel selection. volume control.fault simulation: five built-in simulated faults for troubleshootingexperiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption.pcb size: 15" 12" with multicolour section-wise blockdiagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna.additional features: dth subscription connection withdoordarshanfree channels. free-to-air channel demonstration., fpga trainer kit:specification : must use industry-standard mid-range fpgadevice usb-jtag programmable, compatible withvivado ise (webpack). power supply: 5 v dc through usb or externaladapter. on-board peripherals: leds, switches, pushbuttons, 7-segment display,clock source, gpio /pmod expansion ports, uart, vga / hdmi, usbuartbridge, usb cable. user manual.

CTN :45404506

05 Jun, 2026 NA

Liluah - West Bengal

Tender For supply & installation of set of consisting 09 (nine) items as per annexure attached.- workshop table for electronics repair, hsn: 73012090, bench type digital multimeter, hsn: 90303100, dc power supply 30v 5amp, hsn: 85044090, soldering station, hsn: 85151900, bench-top fume extractor, hsn: 84213990, esd-safe storage box/rack, esd palm fit hand gloves-size -m, hsn: 61161000, crocodile clip, esd slipper - color - blue, hsn: 64029990

CTN :45387970

12 Jun, 2026 NA

Subansiri - Arunachal Pradesh

Tender For supply of communication items - i com air band ic 25 ce , f405 fc drone parts , f405 aio drone parts , dual band mobile , pigen heater 11 fin

CTN :45386611

15 Jun, 2026 NA

Tuticorin - Tamil Nadu

Tender For purchase of lab equipments for basic eng dept - purchase of lab equipments for baisc eng dept (physics and chemistry), digital balance itemcode: a001 weight 500g, accuracy 0.01g, top pan. tare function, caliberation- automatic external display type: led., joule s calorimeter itemcode: a005specifications:copper vessel, battery eliminator 3a, (2,4,6,8,10,12 v), tubular rheostat 20-3.3a, one way plug key, analog type dc ammeter (0 2a), voltmeter (0-5v), thermometer (alcohol), stop clock, ic regulated battery eliminator itemcode: a011specifications:ic regulated, input: 230v ac; output: 0-12v dc in steps of 2v; capacity: 1a or 2a., galvanometer itemcode: a012specifications:moving coil type, 30-0-30 scale, unbranded with bhel specification-sensitivitysensitivity, voltmeter itemcode: a013specifications:dc voltmeter; range 0 10 v, analog., ammeter itemcode: a014specifications:dc (0 - 2 amp), decade resistance box itemcode: a016specifications:resistance box 12 month warranty (dial type) -manganin coil- 2 dials, sonometer apparatus itemcode: a017specifications:sonometer with meter scale attached along with knife edge, tuning forks set 256, 384, 512 ranges, hammer, slotted weight - 500 gm each to a total of 3 kg. brass wire (5 m), travelling microscope itemcode: a018specifications:branded travelling microscope 0 200 mm horizontal and 0-150 mm vertical measurement, potentiometeritemcode: a019specifications:it features a 1-meter to 10-meter constantan/manganin wire stretched on a wooden or sunmica baseboard with a millimeter scale. it includes 4mm brass terminals, a pencil jockey for contact, wire options (10 wires), and a typical resistance range of 10-20 ohms, ideal for high-precision voltage measurements., rheostat itemcode: a021specifications:high-grade ceramic tube, oxidized resistance wire, 0.5a 5a, range 10 100 ., deflection magnetometer apparatusitemcode: a022specifications:deflection magnetometer apparatus with compass box and two short bar magnets, digital electronic balance /analytical balanceitemcode: a001/a007specifictions:load capacity: minimum,500 g readability: 0.01 g,linearity: 0.02g,display: lcd/led,tare function: required,top pan typepower supply: 220 240 v,ac, 50 hz, digital tds meter itemcode: a002specifictions:measuring range: 0 9990,ppm resolution: 1 ppm,display: lcdautomatic temperaturecompensation (atc): requiredwaterproof: minimum ip67 protectionpower source: battery, operated (button cell/aaa, digital ph meter benchtop model itemcode: a003specifications:ph type microprocessor/microcontrolle r ph range: 0 14resolution: 0.01 ph,accuracy: 0.05 ph or better combined ph electrode with temperature sensor two or three-point calibrationfacility temperature compensation type automatic display: lcdpower supply: 220 240 v ac, 50 hz warranty minimum 1 year, laboratory heating mantle (knitted glass yarn) itemcode: a004specifications:capacity: 500ml,temperature range: ambient to 350 c energy regulator/control knob:required power supply: 220-240 v ac,50 hz, mortar with pestle itemcode: a006specifications:material: porcelain size: 100 150 mm inner diameter exterior: glazed grinding surface: unglazed, hot plate itemcode: a008specifcations:top plate material: cast iron plate size: minimum 8 inchdiameter power rating: 2000 w temperature range: ambient o 200 c minimum thermostatic temperaturecontrol: required power supply: 220 240 v ac, 50hz., electric bunsen burner itemcode: a009specifications:electrically operated energy regulator/ control knoboperating temperature 800 c body: stainless steel power supply source: corded electric, supplied with a heavy-duty, heat-resistant,earth-grounded, 3-pin power cord (minimum length 1.2 meters). power consumption: between 350 and 500w power supply: 220 -240 v ac, 50 hz, water distillation unit itemcode: a010specifications:output capacity: 4 litres per hour (lph) ph value: 5.5 to 7.0conductivity (raw water distillation):3.0 4.0 s/cm or less glassware material:borosilicate 3.3 glass (pyrex/duran

CTN :45358061

18 Jun, 2026 NA

Guna - Madhya Pradesh

Tender For supply of various items of lab equipments for govt. p g college guna district guna (m.p.) under p m usha pariyojna 4th call - supply of various lab equipments items for govt. p g college guna district guna (m.p.) 4th call, waterand soil testing analysis kit (digital) : range ph 0 to 14.00 resolution ph 0.01 accuracy ph 0.01 1 digit temp. comp. 0 to 100 deg. c., water bath (06holes) : 6 hole8 ltrs., waterbath(12holes) :12 hole 20 ltrs., water distillation apparatus(single distillation unit 2 litre/hour) : single distillation 5 litres, analytical balance : least cosunt 0.0002g, analytical weight box : 1-100g, fractional weight box : 1-500mg, physical balance : 250gm accuracy 0.1g, digital balance : least count 1mg, single pandigital balance : 0.1mg 200g, digital photoelectric colorimeter : 8 filter,1 ml, digital potentiometer : with hot plate and electrodes, digital conductometer : with cell 1cc and 0.1cc, d.o. meter : polarographic do range: typically 0 to 90 mg/l (milligrams per liter) or 0 to 600% saturation.rdo (optical) do range: usually 0 to 50 mg/l or 0 to 500% saturation., digital naphelo/turbidity meter : digital turbidity cum nephelometer range:-, 200,1000 ntu/jtu resolution:- 0.01 ntu/jtu accuracy:- 3% fs, 1digit display:- 3 digit 7-segment led light source:- ir led detector:- photodiode sample system:- 60 x 25mm clear glass test tubes power:- 230 v 10% ac, 50 hz accessories:- test tube set of 2, operation manual, dust cover, polarimeter half shade : the specific rotation ( ) is a physical property defined as the optical rotation at a path length of 1 dm, a concentration of 10 g/l, a temperature (usually 20 c), and a light wavelength (usually sodium d line at 589.3 nm), melting point apparatus :melting-point measurement range: room temperature - 400 c setting rate of the starting temp. : 50 c~400 c 5 min; 400 c~50 c 7 min minimum digital display: 0.1 c size of the capillary: 1.4mm (outside diameter) 1.0mm (inside diameter), 90mm equipped with color camera and color monitor to observe melting point with ease validation program for standard samples 8 operator names can be storedgraphic lcd display to display all test parameters & test instructions, digital melting point apparatus :melting point measurement range : ambient to 300 deg c starting melting point temperature : settable from 50 to 300 deg c heating time : 3 minutes (up to 300deg c) cooling time : 5 minutes (from 300 deg c) accuracy : +/ 0.5 deg up to 200 +/ 0.8 deg from 200 to 300 temperature display resolution : 0.1 deg c rate of heating (deg c per minute), abbe refractometer : safety bs en 60950-1:11/2006 emc en 55024 : 10/2003 en 55020 : 11/2005, tlc kit : outstanding standardization and quality control exceptional adherence, hardness and surface homogeneity. analyzing samples with high matrix- load without sample preparation. multiple samples analyzed in parallel.highly cost-efficient, fast and economical, centrifuge : 6000rpm, corkboring machine :adjustable guide that permits holes to be bored in any part of a stopper, the knurled chuck - 9/16" (14mm) shank of the eight, plated-steel borers included with the unit. the steel borers range from 3/16" to 5/8" (4.8mm to 15.9mm) in 1/16" (1.6mm) increments,, distillation apparatus : single distillation 5 litres, oven hot air : 14" 14" 14 , voltage stabilizer : 2kv, vertex shaker : 6 tube capacity, mixer small : moter capacity 900 watt, water bath(cu) : 4 , heating mantle with energy regulator : 500 w,2litre, single crucible heater : helical wire coil moldatherm insulation platinel ii thermocouple with 10tm compensated lead wire and polarized plug ceramic fiber hearthplate programmable heat-up to setpoint temperature indicates setpoint and process temperatures temperature: 1200 c (2192 f) maximum crucible sizes: 5 (top vestibule id) x 8 (heated depth), water bath rectangularsingle walled : 6 hole 8 ltrs., water bath rectangular :2 hole, kjeldahl distillation unit : unit of 3 tests, microwave oven : 30 ltr co

CTN :45375032

15 Jun, 2026 NA

Tirunelveli - Tamil Nadu

Tender For supply of electrical goods in the year 2026-2027 in panagudi town panchayat - 1x40 w tube light, 1x40 w copper chocke, 1x40 w tube light starter, tube light side holder, 4ft.alu.street light fittings and chock ,starter without lamp, fittings side tagged, bulb upto 100 w, bulb holder, fittings top clamp, insulation pvc taproll (10 mtr), 250 w sodium vapour lamp, 250 w sodium vapour choke, 250 w sodium condenser (33mfd), 250 w sodium vapour ignator, 250 w s.v. lamp holder, 250 w s.v.fittings complete set (without lamp), 150 w sodium vapour lamp, 150 w s.v.chocke, 150 w s.v.condencer, 150 w s.v.ignator, 150 w s.v.fittings, 150 w s.v.holder, 70w s.v.lamp, 70w s.v.chocke, 70w s.v.condencer, 70w s.v.ignator, 70w s.v.fittings, 70w s.v.holder, 125 w m.v.chocke, 125 w m.v.condencer, 125 w m.v.holder, 125 w m.v.lamp, 1x40 watts heavy duty electronics chocke, 400 w m.h.lamp, 400 w m.h.chocke, 400 w m.h ignator, 400 w m.h.condencer, 400 w m.h flood light fittings, 400 w m.h control gear box, 250 w m.h. lamp, 250 w m.h.chocke, 250 w m.h ignator, 250 w m.h.condencer, 250 w m.h.fittings, 150 w m.h.lamp, 150 w m.h.chocke, 150 w m.h.ignator, 150 w m.h condencer, 150 w m.h.fittings, 70w m.h.lamp, 70w m.h.chocke, 70w m.h.fittings, 1/18 pvc copper wire (90 mtr), 3/20 pvc copper wire (90 mtr), 7/20 pvc copper wire (90 mtr), 7/18 vir copper wire (90 mtr), 7/16 pvc copper wire (90 mtr), hookup wire (90 mtr), 1.5 sqr mm alu. wire (90 mtr), 3/20 pvc aluminium wire (90 mtr), 7/20 pvc aluminium wire (90 mtr), 18 pvc aluminium wire (90 mtr), 7/16 alu.pvc wire (90 mtr), silk wire 2core copper, s.v.clampset with bend pipe, t5 fitting clampset, bend pipe with wire, cfl fittings clampset with bend pipe, st.light clampset bend pipe, sodium vapour acurlic cover, st.light fittings acurlic cover, cfl acurlic cover, st. light automatic on/off digital timer control panel board with 40amps contactor.., st. light automatic on/off mechanical timer control panel board with 40amps contactor., 7 days mechanical clock, electronics 7 days digital clock, electronics 7 days clock battary, 40amps contactor control switch, contactor coil 220v-250v, st.light switch box, main,clampset with service pipe, t5 2x24 watts power saver chock., t5 power saver lamp 24 watts, 2x24 watts t5 flourescent power saver street light alu. die cast fittings(ip 65) with lamps., 2x14 watts t5 flourescenr power saver street light alu die cast fittings(ip 65) with lamps., 4x24w t5 flourescent power saver alu fitting, chock with lamps., t5 power saver patt fittings with lamp 28watts, 36w compact flourescent lamp(cfl)., 36watts cfl chocke, 1x36 watts compact flourescent lamp (cfl) fittings, industrial electronics type chock withlamp, 2x36 watts alu st. light compact flourecent lamp(cfl) fittings, industrial electronics type chock withlamp ., fan (crompton), gi wire 7/20., gi wire 20 no., hand clous set, solar light post 11watts cfl with all accessories complete set, d.p switch 32a/240v, solar light post 15watts led with all accessories complete set, solar light post 20 watts led with all accessories complete set, solar light post 10watts led with all accessories complete set, cfl 20 watts direct, cfl 15 watts direct, fuse unit 16/240 volt, fuse unit 16/415 volt, fuse unit 32/415 volt, fuse unit 63/415volt, fuse unit 100/415 volt, fuse unit 200/415 volt, fuse unit 400/415 volt, main switch 16/240 volt, main switch 32/240 volt, main switch 32/415 volt, main switch 63/415 volt, main switch 100/415 volt, main switch 200/415 volt, single pole mcb, 4pole mcb, mcb box, 20 w led street light luminaire comprising of epoxy power coated hsg. enclosed with glass cover in frame., 24 w led street light luminaire comprising of epoxy power coated hsg. enclosed with glass cover in frame., 30 w led street light luminaire comprising of epoxy power coated hsg. enclosed with glass cover in frame., 48w led street light luminaire comprising of epoxy powder coated hsg. enclosed with glass cover in frame., 50w led street light

CTN :44721121

04 Jun, 2026 32.34 Lacs

East Khasi Hills - Meghalaya

Tender For bid to ras supply of flag stand as per sample , white board , writing foldale and portable table top , ups battery 12v 7ah , hadn towel microfiber , borosil water jug 1 ltrs , coffee mug , display screen , ruuber stamp , name plate , attendence register as per sample , rubber stamp , name plate , towel large size , hand towel size , pad lock 75mm , key tag box , borosil glass , cup and saucers , serving tray steel , coaster melamine , table cloth blue , table cloth red , tissue paper box , plastic water dispenser bottle 20 ltrs , yoga mats , glass bowl for microwave 750 ml , clip pad omega , quarter plate ceramic , full plate ceramic , tea spoon , lamination paper a4 size , lamination paper legal size , lamination paper a5 size, a6 size , tissue holders steel , ceramic flower pots , automatic room freshner , spare catridge for automatic room freshner , wireless keyboard mouse , national flag , carpet , disposal paper cup , disposal water drinking glass , dust bin plastic 16 ltr , dust bin steel , umbrela large , extension board three switch and socket , birds photo with name hindi english size , padlock 7 lever , cotton towel , executive leather cover dairy , frame for calendar , toffee bowls , cordless phone , corps of engr flag , usha water dispenser with jar , cintrotech biodegradable packing material 18 inch 100 meters length , franking machine ink , clip board leather , long roll book 400 pages as pe rsample , paper cup dispenser holder wall mounted , stainless steel bench two seater silver color , frame for calendar , pilot v5 blue pen , pilot v5 black , pilot v5 red pen , red carpet , decorate cotton rectangular floor mat, dari , table cloth red colour , foot mat , cat 6 cable , women bathroom signage acrylic board , do pad , name plate ace as per sample , heavy duty asjustable folding stand for whiteboard , comb binding machine , yoga mat , steel dustbin 18 ltr ss without lid , disposal glass , pen stand as per sample , calling bell , coaster , v5 pen , mouse pad , bty charger , helmet , veh tool set , tyre wash brush , oil can , rebustt heavy duty rubber hand gloves , cottong gardening claws gloves , welsafe safety gumboots with lining black , glass bottle 350ml , garden watering can 5 ltrs , digital pressure gauge , tow chain , halogen heater , oil heater 13 fn , pedestal fan , oil heater 9fn , portable electric kettle , oil heater 11fn , 3 mtr mini usb 2 cable for dvd writer , external cddvd writer , oil heater 13 fin , electric kettle 2 ltr , wireless callbell , double rod heater , digital wall clock red led square , digital wall clock , bty 1.5v aaa , bty 1.5v aa , microwave 30 ltrs , electric kettle 2 liter , inducation stove , jbl bar 1000 pro , telescopic ppt pointer adjustable length upto 150cm , laser pointer , wireless presenter as per sample , cable for speaker , visitor chair , revolving chair //bid details 2 / 103

CTN :45379134

10 Jun, 2026 NA

Arakandanallur - Tamil Nadu

Tender For for electrical and communication engineering department lab equipments are required as per new syllabus - upgradation of labarotariesece department, 8051 micro controller kit operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., single phase induction motor1 hp, 230 v ac, 1500 rpm with loading arrangement 1 no.voltmeter: (0 300) v ac, 96 96 mm with input terminals 1 no.ammeter: (0 10) a ac, 96 96 mm with input terminals 1 no.wattmeter: 2 kw, 96 96 mm with input terminals 1 no.power factor meter: 96 96 mm with input terminals 1 no.auto transformer: 0 300 v, 1 variac 1 no.mcb: 2-pole, 40 a / 230 v ac 1 no.digital rpm indicator with proximity sensor 1 no.aluminium brake drum: 230 mm diameter 1 no.spring balance: (0 25) kg 02 nos.circuit diagram printed on front panel with instruments and connecting terminals.motor and loading arrangement mounted on rigidchannel frame with anti-vibration mounting pads, m12 1.5 bolt & nut, 85 mm dia 4 nos.mild steel powder-coated electrical panel tablesetup., auto transformerinput: 230 240 v ac, 50 hz.output: variable (0 270) v ac.rating: 1 kva.insulation class: class f / class h.construction: copper winding with carbon brush arrangement.mounting: bench-top / panel type.protection: suitable fuse / overload protection., dth trainer kitpower supply: 200 v to 240 v ac, 50 hz. dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter): input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency:tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m. controls: channel selection. volume control. fault simulation: five built-in simulated faults for troubleshooting experiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption. pcb size: 15" 12" with multicolour section-wise block diagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna. additional features: dth subscription connection with doordarshanfree channels., sim reader trainer kitpower supply: operates on 230 v ac 10%, 50 hz mains supply. built-in regulated smps power supply. operating dc supply: 5 v / 12 v with overload and short-circuit protection.sim card interface: supports gsm sim cards compatible with 2g / 3g / 4g / 5g networks. sim card read/write interface. supports sim card initialization, authentication, and communication functions. compatible with standard 6-pin / 8-pin sim card sockets.communication interface: usb 2.0 interface for pc communication. rs-232 serial communication interface. uart communication facility for embedded system interfacing.sim operating parameters: selectable sim clock frequencies: 3.579 mhz 7.159 mhz 14.318 mhz sim supply voltage selection facility. sim reset and activation control. supported protocols and standards: gsm etsi 07.07 and etsi 07.05 at command support. iso/iec 7816 smart card communication support. sim communication command monitoring facility. hardware features: on-board sim card socket. led indication for: power status sim detection reset activity data transmission/r

corporations/Associations/Others

CTN :45370437

20 Jun, 2026 NA

Multi City - Multi State

Tender For supply of top plug , top plug , modular box , mcb box 4 way , modular box , duracell aa type , mcb sp 6a , mcb sp 16a , mcb dp 32 amp , led batten 20 watt 4 ft , led batten 10 watt 2 ft , fan regulator stem type modular legrend , fan capacitor 2.5 mf , capacitor 4 mf , capacitor 6 mf , insulation tape , copper wire , electrical cable , pvc gitti , pvc round plate 4inch , casing capping 02 meter , casing nail pin , flexible pipe for electric wire purpose16 to 20 mm , screw , profile light , wall fan , non metalic exhaust fan , metalic exhaust fan , starter , led flood light , aluminium thimble , heat shrink joint , taflon tape , cpvc pipe solvent , aggrigate , cement , pvc connection , float valve , m seal , pvc tank , fevicol , nails assorted size , digital clamp meter , digital multimeter , combination pliers , side cutting pliers wire striper , electric tester , screw drivers kit with seven screw drivers , ball hammer medium , measurement tape , electric rotary hammer drill machine 720 watt or above wired , tct drill bit for sds plus hammers drill bit for sdsplus or wall , tct drill bit for sds plus hammers drill bit for sds plusfor wall , tct drill bit for sds plus hammers drill bit for sds plus for wall , hss tin metal drill bit for sds plus hammers having size sds plus hss tin metal , hss-tin metal drill bit for sds plus hammers having size sds plus hss tin metal , 20mm cold chisel for sds plus hammers cold chisel for sds plus hammers , core bit for sds plus hammers core cutter set for hole in rcc wall , aluminium step ladder with platform , square driver set , strap filter wrench , rotary barrel pump , screw spanner kit , graded stainless steel spade kassi handle , pic axes with handle , sabbal iron road , tasla iron type , chiesel , hand gloves for electrician insulated rubberised , hexa blade , hexa frame , wd 40 spary , ring spanner , wrench heavy duty taparia make , adjustable spanner heavy duty taparia make , trowel karni , plumb bob , wooden iron plaster float finishing tool , spirit level freeman , pipe wrench heavy duty taparia make , hand saw , allen key set box

CTN :45343668

11 Jun, 2026 NA

Madurai - Tamil Nadu

Tender For purchase of equipments for materials testing lab for civil department - spring testing machineload & displacement sensing load cell capacity: 0 10 kn accuracy: 1% fs (better if 0.5%fs) displacement sensor lvdt / digital encoder accuracy: 0.5 mmmachine design frame: rigid steel frame with crosshead movement type: mechanical screw with hand wheel (simple & robust) or electromechanical actuator (for smoother, controlled motion) crosshead travel: ~150 200 mm safety guards: transparent shields around moving partsfixtures & accessoriesspring testing compression plates (ground & parallel) tension hooks / eyelets for extension springs set of spacers / adapters for small springs tensile testing standard tensile grips wedge or screw type calibration certificate for load cell standards complianceensure compliance with basic material test standards such as: astm e4 / iso 7500-1 calibration of force measurement astm e8 / iso 6892 tensile performance & accuracy load accuracy: 1% fs displacement accuracy: 0.5% repeatability: 0.5%, rockwell cum brinell hardness testing machine min initial test force :10kgf, total test force range : 60kgf,100kgf,150 kgf, max. height of specimen :215 mmmin distance from indenter center tomachine wall :132 mm accessories : steel ballpreferred indentor 1/16" preferred steel ball: 1/16"and with all standard accessories to run the machine, direct shear machinestandard compliance:the equipment shall confirm to bureau of indian standards is 2720 (part 13) and equivalent astm international astm d3080.technical specifications:shear box size: 60 mm 60 mm 25 mm specimen size (complete with grid plates, porous stones, and specimen cutter).normal load capacity:minimum 5 kn with loading yoke and calibrated loading hanger set.shear load capacity:minimum 2.5 kn or 5 kn with calibrated proving ring (with calibration certificate).rate of strain (shear displacement):variable speed drive with controlled displacement ranging from 0.01 mm/min to 1.25 mm/min (motorised model preferred for uniform rate control).displacement measurement:horizontal displacement dial gauge: 0.01 mm least countvertical displacement dial gauge: 0.002 mm or 0.01 mm least countloading frame:rigid, heavy-duty loading frame with corrosion-resistant finish.drive system:motorised with single phase 220 230 v, 50 hz power supply.accessories (to be supplied complete):shear box assembly, proving ring with calibration chart, two dial gaugesloading weights and hanger, porous stones (2 nos.), specimen cutter, tool kit, flow table test apparatusdimensions and specifications as per is 9103, table top made from flat metal plate, minimm thickness 1.5 mm. table top size: 700 mm 700 mm, with flatness tolerance of 1.5 mm. table top marked with: scribed cross at centre, lines parallel to table edges and central circle of 200 mm diameter underside of table top reinforced to prevent distortion. total mass of table top: 16 1 kg. table top, base frame front and upper stops provided as per is 9103. lower front edge fitted with two rigid stops to transfer load directly to base frame. base frame designed to transfer impact load directly to supporting surface, minimizing bounce. stop watch digital - 2 nos scale 1 mtr 2 nos mounting wooden platform 300 mm height amc for 3 years inclusive.

Communication Item Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

corporations/Associations/Others