Get complete information related to latest Conduit Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Conduit Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Conduit Tenders.
Tender For supply of out rigger swing cylinder for 140t dhbd new design crane, bore: 50mm, sr- single rod, c m- clevis male, wcg- welded cylinder gland, rod- 36mm, stroke: 213 mm, ge30 iko bearing, tube materi al - st 52.3, rod : c45, 25 micron thick, operating pressure - 250 bar, test pressure - 375 bar, ports ? inch bsp welded sockets with 10 mm conduit tube from rod side. equivalent to hydrodyne part no. 50-*-sr-cm- wcg-36-r-*-213 [ warranty period: 30 months after the date of delivery ]
Tender For auction sale of scrapautomatic slack adjuster,scrap break drum tata/ley/eicher,scrap wheel tyre disc,clutch plate tata/ley/eicher,scrap pressure plate tata/ley/eicher,scrap deration tank,used/burnt oil with barrels 210ltr capacity,empty plastic barrel 210 litre capacity,empty oil barrel dented or rusted,empty grease barrel210 litre capacity,scrap seat frame with luggage carrier,ms scrap,scrap wheel disc (tube less tyre disc),spring leafs including below 1 feet,sping leafs less than 1 feet rousted,scrap bvc tin 20 litre capacity including dented or rousted,scrap curing envelops 1000x20 torned,scrap flywheel rings tata/ley/eicher,front /rear break shoe with or without linings,scrap turbo charger assembly,scrap pressure plate back plate tata/ley/eicher,scrap air cooler 20 ltr capacity,scrap fire extinguisher 2kg/5/kg/9kg,scrap hydraulic /mechanical jack bottol neck 10 ton capacity,scrap dd unit /air dryer assembly,scrap wiper motor tata/ley/eicher,scrap battery charger machine,scrap air compressor,water pump (ley/tata/eicher),scrap ac head assy,scrap centre joint shaft,scrap push rod assy,scrap belt tensioner,scrap king pin bushes,auto electrical items,scrap drive assy,scrap silencer muffler,fip spare hydralic head,nozzle,gear parts syncro cone,cam plate,scrap engine bell housing,scrap cross member,bearings,auto items grade 2,tread rubber powder and cut pieces,scrap flaps full rounds 1000x20 torned ,scrap cut flaps,scrap tubeless tyre 235/75r radial /nylon (lot-l1),scrap tyre 1000x20 radial(lot-g),scrap tyre 1000x20 radial (lot-b),scrap tyre 1000x20 radial (lot-c),scrap tyre 1000x20 radial (lot-d),scrap tyre 1000x20 radial (lot-a),scrap tyre 1000x20 radial (lot-e),scrap tyre 1000x20 radial (lot-f)
Tender For supply of steel tube galvanized isi mark in random length 4 to 7 mtrs screwed at both ends sock eted at one end and other end protected with plastic protecteor, nominal bore 15 mm medium class, socket shall also be isi marked. specn: mat specification : is-1239 ( pt.-1) :2004 for tube, is: 1239(part -2): 2011 for socket and is::554:1999 for pipe thread. [ warranty period: 30 months after the date of delivery ]
Tender For corrigendum : repair of furniture for units in aor of stn hq bg under ge 881 ews - almirah large steel fd-351,339, 1031, removing unsv shelves of almirah large steel and s&f new shelves made out of 1 mm thick ms sheet with suitable clips/brackets/gas welding (if any) complete all as specified and directed by engr-in-charge., removing unsv foot rest of almirah large steel and s&f of new foot rest made out of 1.6mm thick ms sheet with continuous gas welding complete all as specified and directed by engr-in -charge., removing unsv lock of almirah large steel and s&f of new lock of six lever with duplicate key with suitable nuts and bolts all as specified and directed by engr-in-charge. make godrej/harrison/link, removing of unserviceable handle of almirah large steel and s&f of new steel handle 150mm long with suitable steel nuts and bolts complete all as specified and directed by engineer-in-charge., removing of unserviceable locking device of almirah large steel, s&f of new three way locking device (chakra/locking rod and locking cover) made out of ms round bar 10mm dia all as specified and directed by engineer-in-charge., removing of unserviceable key plate of almirah large steel, s&f of new key plate all as specified and shown on drg., welding per 5 cm wherever necessary, all as specified and directed by engineer-in-charge., m & l for two coats of synthetic enamel paint (1st grade quality shade/colour shall be approved by engineer-in-charge) including denting and painting of almirah steel large throughout inside and outside complete with spray machine after properly smoothing the surface all as directed by engineer in-charge., almirah med steel (fd-243, 340, 1032), removing unsv shelves of almirah med steel, s&f of new shelves made out of 1 mm thick ms sheet with suitable clips/ brackets/gas welddng (any one) all as specified and directed by engr-in-charge., removing unsv foot rest of almirah med steel, s&f of new foot rest made out 1.6mm thick ms sheet with continuos gas welding all as spcified in and directed by engr-in-charge., removing unsv lock of almirah med steel, s&f of new lock of six lever with duplicate key with suitable nuts and bolts all as specified and directed by engr-in-charge. make - godrej/harrison/link, removing of unserviceable handle of almirah med steel, s&f of new steel handle 150mm long with suitable steel nuts and bolts all as specified and directed by engineer-in-charge., removing of unserviceable locking device of almirah large steel, s&f of new three way locking device (chakra/locking rod and locking cover) made out of ms bar round 10mm dia all as specified and directed by engineer-in- charge., removing of unservicable key plate of almirah med steel, s&f of new key plate all as specified and shown on drg., welding per 5 cm wherever necessary, all as specified and directed by engineer-in-charge., m & l for two coat of synthetic enamel paint (1st grade quality shade/colour shall be approved by engineer-in-charge) including denting and painting of almirah steel medium throughout insided outside complete with spray machine after proper smoothing the surface all as directed by engineer in-charge., locker bed side steel (fd-1029), removing of old unsv hasp and staples of locker bed side steel and s&f of new ms hasp and staples as specified in drg and approved by the engr- in- charge., removing of old unsv conduit pipe of locker bed side steel and s&f of new cp steel 16mm dia 22 guage conduit hanging pipe all as specified and directed by engineer-in- charge., removing of old unsv handle of locker bed side steel and s&f of new cp steel handle 150 mm long as approved by engineer-in- charge., removing of old unsv hinges of locker bed side steel and s&f of new ms hinges 75mm long as approved by engineer-in- charge., removing of old unsv foot rest of locker bed side steel and s&f new foot rest made out of 1.6 mm thick ms sheet with co