Get complete information related to latest Coupling Shell Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Coupling Shell Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Coupling Shell Tenders.
Tender For maintenance of mi scheme under belbari rd block during the year 2025-26/sh_ - repair _ maintenance of pump-motor, suction-delivery _ electrical accessories etc. (job no. tr/34/minor works/wrd-i/2025-26) - dismentling of pump for over hauling including greasing, gland packing, necessary repairs & reinstallation of the same including trial run for 10 hrs. in two spell complete as per direction of the engineer-in-charge.i) for li, supply & fitting fixing ball bearing of approved quality for pump required during overhauling.i) 6306 ball bearing (tata /skf), providing & fitting fixing shaft sleeve bush of approved quality.i) for li (cast iron), providing & fitting fixing shaft sleeve nut of approved quality.i) cast iron (ci), providing & fitting fixing c.i. gland of approved quality.i) for li, providing & fitting fixing c.i coupling complete with nuts & bolts of approved quality.i) 150 mm dia, providing & fitting fixing coupling nuts & bolts (all size)of approved quality.i) for li, providing & fitting fixing coupling rubber bush (all size)of approved quality. i) for li, providing & fitting fixing coupling star bush (all size) of approved quality.i) 150 mm dia, providing & fitting fixing pump shaft of approved quality., supplying and fitting fixing of asbestos rope of best quality as per direciton of engineer-in-charge. i) 6mm to 8mm thick, ii) 10 to 12 mm thick, providing & fitting fixing casing ring of approved quality.i) 150 mm dia (10 mm thick), supplying and fitting fixing of pump cooling pipe of best quality as per direciton of engineer-in-charge., providing & fitting fixing lantern ring for pump of approved quality., supplying and greasing/applying of grease of approved quality as per direction of engineer-in-charge., providing and fixing g.i. bend /elbow in the pipe line including testing of joints complete as per cpwd specification and direction of the engineer - in - charge. a) 150 mm dia, providing & fitting fixing shaft sleeve nut of approved quality. (cast iron), providing & fitting fixing of g.i. flange ( 10 mm wall thickness ) by welding with g.i. / ms pipe and placing position as per specification and the direction of the engineer-in- charge.i) 150 mm dia, providing & fitting fixing gland nut / stag nut 100 mm long for gland of approved quality.i) for li, providing and fitting fixing m.s. clamp for hose pipes with nuts & bolts complete as per relevant is specification anddirection of engineer-in-charge.i) 150mm dia, providing & fitting fixing rubber flange washer 6 mm thick at site of work of approved quality.i)150 mm dia, providing and fitting fixing ms foot valve as per relevant is specification and the direction of the engineer-in-charge.. i) 150 mm dia, providing & fitting fixing c.i tail piece of approved quality at site of work.i) 150 mm dia, providing & fitting fixing foot valve leather washer (6 mm thick) of heavy duty at site of work of approved quality.i) 150 mm dia, providing & fitting fixing c.i foot valve spare parts of 125/150 mm dia at site of work of approved quality.a) c.i foot valve weight, b) c.i foot valve ring, c) c.i foot valve net, dismantling of motor fpr vernishing heating etc cpmplete in/c reinstalltion and trail run for two spell complete as per direction of the engineer-in charge., supplying & fitting fixing of spare parts for 20/25 hp horizontal motor.a) motor fan, b) terminal plate, providing and fitting fixing of fully automatic star delta type motor starter ( 3 ph. 50 hz, 415v, 25hp /18.50 kw relay range within 17-25 ) in steel sheet enclosures with contractors and timer etc. complete suitable for motor pump havells/l & t/bch make direction of the engineer-in-charge.i) 25hp/18.5kw relay range within 13-21 +10%, providing and fitting fixing steel sheet enclosed switch fuse unit (suitable for din fuses). triple pole with neutral link ( tpn ) , 415/500 volt complete as per direction of the engi
Tender For supply of 1- body casing, part no - 1, moc - c.i with ss-316 lining,2- head le and de, part no - 2, moc - c.i with ss-316 lining,3- cone ie and de, part no - 4-1 and 4-d, moc - c.i gr.fg-260,4- rotor shaft assembly complete with shaft sleeve lock nuts lock washer and coupling key alt-1, part no - 3,5,21,13,14 and 19, moc - rotor ss-316, shaft en-24, sleeves ss-316,5- packing head and body, part no - 7, moc - non asbestos,6- packing head and cone, part no - 8, moc - non asbestos,7- bearing cover d.e inner, part no - 9-d, moc - c.i gr fg 260,8- bearing cover i.e inner, part no - 9-i, moc - c.i gr fg 260,9- bearing cover d.e outer, part no - 10-d, moc - c.i gr fg 260,10- bearing cover ie outer , part no - 10-i, moc - c.i gr fg 260,11- set of shims or spacer, part no - 11, moc - p.b,12- packing de inner and housing, part no - 15, moc - paper,13- gland, part no - 16, moc - c.1 gr fg -260,14- packing rope -gland, part no - 17, moc - asbestos free teflon packing rope,15- oil seal inner covers, part no - 18, moc - rubber,16-oi
Tender For procurement of spares of acw and fire fighting pump of 210 mw, atps mppgcl chachai. - shaft collar, brg lock nut (de & nde), seal cover, wearing ring casing, fire hydrant pump model no.: fig- f5826 size- 200 x 150, single stage - dr. no. - csd 503 03 03 2k7 (a), make - flowmore, seal ring, shaft sleeve, pump shaft, brg lock washer, brg lock nut, pin bush set for motor pump coupling
Tender For supply and delivery of one number bare shaft centrifugal pump vertical execution with half coupling of capacity 5600 m3/hr., 24 metre head for raw water pumping station, phase-ii of grww.
Tender For centralized rate contract for two (02) years of spares of sam turbo make pumps installed in ash handling plant of dvc - impeller with screw & hub cap : part no : -18 & 38, 58 : material: - nihard type iv (550 bhn) / 24% chromium ci (550 bhn), fasteners set (total quantity of fasteners applicable for one bare ba overflow transfer pump, model : arl 200/410 ) : part no : -na : material: - ms / hts, lock washer (p.end) : part no : -63 : material: - is 1363 ms, piston ring : part no : -51 : material: - is 210 fg 200, key (coupling) : part no : -32 : material: - bs 970 en 8, laybrinth (drive end) : part no : -24 c : material: - astm a 216 gr wcb, coupling set [od 280 mm] : part no : -na : material: - is 210 fg 200, base with top cover : part no : -1 & 2 : material: - is 210 fg 200, volute casing : part no : -17 : material: - nihard type iv (550 bhn) / 24% chromium ci (550 bhn), lock nut (p.end) : part no : -60 : material: - is 2062 c 15, grease nipple : part no : -48 : material: - steel, lock washer : part no : -47 a : material: - is 1363 ms, check nut : part no : -47 : material: - astm a 216 gr.wcb, key (shaft sleeve / impeller) : part no : -31 : material: - aisi 304, bracket side cover : part no : -25 : material: - astm a 216 gr wcb, laybrinth (pump end) : part no : -24 : material: - astm a 743 cf8, shaft sleeve : part no : -12 : material: - aisi 410 (h), gland : part no : -10 : material: - astm a 216 gr.wcb, grease retainer : part no : -7 : material: - is 210 fg 200, wear plate (b.side) : part no : -16 : material: - nihard type iv (550 bhn) / 24% chromium ci (550 bhn), pump shaft with keys : part no : -4 : material: - bs 970 en 8, lantern ring : part no : -13 : material: - aisi 410, gland housing : part no : -9 : material: - alloy ci (290 - 320 bhn), end cover : part no : -5 : material: - is 210 fg 200, ba overflow transfer pump complete without motor, model-arl 200/410, earlier pump sl.no.-16804-16805, head:20mwc, capacity: 320 cubic meter/hr., size:200x200., o ring set (1 set=8nos.), for ba overflow transfer pp, model of pump-arl 200/410, shaft sleeve : part no : 53.6 : material : aisi 410, impeller with nut & helicoil insert : part no : 24.2 : material : is 318 gr.i, bearing housing lantern : part no : 35.6 : material : is 210 fg 200, bearing bed : part no : 36.7 : material : is 210 fg 200, bearing cap(outer) : part no : 37.2 : material : is 210 fg 200, bearing cap(inner) : part no : 37.3 : material : is 210 fg 200, oil seal set (1set = 2 nos) : part no : 43.13 & 43.3 : material : syn. rubber, impeller nut with helicoil insert : part no : 93.4 & 94.21 : material : aisi-316, wear ring (casing) : part no : 51.4 : material : is 318 gr.ii, wear ring (casing cover) : part no : 51.23 : material : is 318 gr.ii, key(coupling) : part no : 95.2 : material : bs 970 en8, circlip : part no : 94.23 : material : spring steel, grooved nut & lock washer : part no : 93.3 & 94.03 : material : sae 1018/1020 is 513 crca sheet, gland : part no : 46.4 : material : is 210 fg 260, pressure ring : part no : 46.9 : material : aisi 410, lantern ring : part no : 46.10 : material : aisi 410, gland packing set (1set = 4 nos) : part no : 47.3 : material : tiga, fastners set [total quantity of fastners applicable for one bare ash conditioner water pump, model : cpc 80/400 ] : part no : na : material : ss, key(impeller) : part no : 95.03 : material : aisi-316, key (sleeve) : part no : na : material : aisi-316, gasket set (1set = 4 nos) : part no : na : material : caf-9/ paper oil resist, volute casing : part no : 11.4 : material : is 210 fg 260, pump shaft with keys : part no : 22.3 : material : bs 970 en8, disc (impeller) : part no:550 : material :-ansi-316, gland : part no:452 : material :-astm a 743 gr.wcb, lantern ring : part no:458 : material :-aisi 410, key (impeller / shaft) : part no:940.01 : material :-aisi 316, lock washer : part no:931 : material :-sae 1018/1020, bearing cover (n.d.e) : part no:360.01 : material :-ast
Tender For supply of circlip b22 part no.061 022010 , oil seal for yoke part no.071 907010 , oil seal for worm shaft part no.071 633813 , gasket set part no. 27 35 xx 0 pr60 , plunger dia 20 mm part no 41 45 53 1 spare for phosphate dosing pump model pr60 , gland packing set of 05 nos part no 41 45 57 0 spare for phosphate dosing pump model pr60 , guide pin part no 27 10 09 0 spare for phosphate dosing pump model pr60 , complete bare shaft pump with base plate foundation bolt coupling and coupling guard spares for phosphate dosing pump , guide ring part no 41 45 56 0 model pr60 , gland retainer part no 27 45 34 0 model pr60 , eccentric strap part no 27 20 01 0 model pr60 , bearing retainer part no 27 50 08 1 model pr60 , throat bush part no 27 45 35 0 spare for phosphate dosing pump model pr60