Get complete information related to latest Crow Bar Scrap Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Crow Bar Scrap Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Crow Bar Scrap Tenders.
Tender For corrigendum : supply of spares for kirloskar make pumps different model - delivery casing vde , suction casing , set of o ring 5 stage , oil seal de nde , set of tie bar with nut and washer 4stage , liquied deflector , impeller 1st stage , impeller 2end stage , pump shaft cw ccw , wear ring , interstage ring , split gland , lantern ring , shaft sleeve , shaft sleeve , bearing cover de , bearing cover nde , bearing cartridge de ci , bearing cartridge nde ci , rotating assembly , impeller i stage , impeller ii stage , bearing housing unit , wear ring , pump shaft , rotating assembly , enclosed impeller , shaft sleeve suc.side , shaft sleeve del.side , stage casing , diffuser with guide vanes , cooling chamber , diffuser , shaft sleeve de nde , shaft cw ccw , casing wearing ring suc , casing wearing ring del , impeller , bearing housing unit , rotating assembly bid number/ & ( * ) : gem/2025/b/6169215 dated/ + : 05-05-2025 bid document/ 1 1 1 / 53
Tender For supply of gear fly wheel ring , gear lever knob , pad hydraulic rampad torison bar , assy rear brake actuator scl , speedo cable jis 3000 mm , front wiper blade , rear wiper blade , de bearing , dog kit , assy ball joint , shifter fork 1st rev , petrol tank cap assy lockable , breather pipe , assy oil filter , head light bulb , oil seal extension , air drier and cooler pipeline , assy pipe , pipe line
Tender For providing and fixing electrical equipments accessories mechanical spare parts and electrical installation to pump house at paddal and tarna - providing and fixing new ball bearing 7312 skf make (begap) complete in all respect as per the direction and to the entire satisfaction of the engineer-in-charge in all leads and lifts., providing and fixing new ball bearing nu 412 skf make complete in all respect as per the direction and to the entire satisfaction of the engineer-in-charge in all leads and lifts., providing and fixing new ball bearing 6314 skf make complete in all respect as per the direction and to the entire satisfaction of the engineer-in-charge in all leads and lifts., providing and supplying gland dori 16 mm in all leads and lifts., providing and supplying gland dori 14 mm in all leads and lifts., providing and supplying gland dori 10 mm in all leads and lifts., repair / overhauling of 5.00 hp monoblock pump set including cost of change of ball bearing no. 6307 & 6308 in 2 nos. pump sets and dismentling, assembling, testing and carriage of pump at site of work including labour charges complete in all respect as per the satisfaction of engineer-in-charge in all leads and lifts., repair / overhauling of 200.00 hp centrifugal pump set including cost of change of sleeves, cleaning and regreasing of all bearing and dismentling, assembling, testing and carriage of pump at site of work including labour charges complete in all respect as per the satisfaction of engineer-in-charge in all leads and lifts., providing and supplying rechargeable led torch 3 watt (wipro) make complete in all respects and to the entire satisfaction of the engineer-in-charge., providing and fixing three core submersible flat cable 10.00 sq. mm for submersible pump set of plaza / finolec make in all leads and lifts., wiring for light point/ fan point / exhaust fan /call bell point with 1.5 sq. mm. pvc insulated heat resistant flame retardant (hrfr) and low smoke single core (flexible) copper conductor cable in surface/recessed pvc conduit and earthing the light point with 1.5 sq.mm. hrfrls/pvc insulated single core copper conductor cable as required., supplying and fixing metal box of 180mmx100mmx60mm deep (nominal size) on surface/recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 5 pin 5/6 amps socket outlet and 5/6 amps, piano type switch, connections, painting etc. as required., supplying and fixing metal box of 180mmx100mmx60mm deep (nominal size) on surface/recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 6 pin 15/16 amps socket outlet and 15/16 amps, piano type switch, connections, painting etc. as required., wiring for circuit/sub-main with following size pvc insulated heat resistant flame retardant (hrfr) and low smoke single core (flexible) copper conductor cable in surface/recessed pvc conduit along with 1 no. hrfrls/pvc insulated single core copper conductor cable of same size for earthing as required.2x1.5 sq. mm., 2x10.0 sq. mm., supplying and erection of 6 amps. to 32 amps. rating, 10 ka breaking capacity, 240 volts, c curves, miniature circuit breaker of following poles in the existing mcb db complete with connections etc. as required:- single pole. cat-a., supplying and erection of 40/50/63 amps rating. 10 ka breaking capacity, 240 volts, c curves, miniature circuit breaker of following poles in the existing mcb db complete with connections etc. as required:- double pole. cat-a., supplying and fixing of following way, single pole and neutral sheet steel mcb distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:-single door-6 way, supplying and fixing bakelite batten/angle holder including connect
Tender For repair and overhauling service - ground equipment;ground equipment; no; buyer premises-scope of work for servicing of ground equipment- regular servicing and preventing maintenance of ground equipment is essential to ensure the safety, efficiency, and reliablility of ground operations. gsse plays a critical role in supporting aircraft turnaround, maintenance, and logistics function. over time, continous use of equipment such as ladders, hydraulic rigs, trolleys, towing arms, and refilling systems can lead to mechanical wear, fluid degradadation, and unnoticed structural fatigue. faulty or poorly maintained gse poses a direct risk to personnel, aircraft, and ground assets. servicing ensures that all mechanical, hydraulic and structural components function safely and as intended. scope of work: 1. ladder frame to be inspected and weld joints for cracks for deformation and it is to be repaired. 2. anti-slip steps, handrails and safety locks to be inspected and to be rectified/changed. 3. caster wheels are to be checked for wear, lock function and lubrication and all the faulty parts are to be repaired/changed as per condition of the(f) equipment. 4. brake function and tow hitch mechanism is to be checked and to be repaired/changed as per condition of the equipment. 5. rust to be removed where required. 6. hoses and fittings are to be inspected for leaks and damages and thoses are to be repaired. 7. filters are to be changed if required. 8. cylinders are to be checked for cracks and are to be repaired. 9. structural integrity of frame and platform is to be checked and repaired as per requirement. 10. wheels are to be checked for alignment or any other bearing issues anfd same is to be repaired. 11. parking brake is to be checked along with the towbar assembly and is to be repaired as per requirement. 12. load securing hooks or rails are to be checked and to be made operational. 13. reservoir is to be checked for contamination and fuel level 14. hand/foot operations is to be checked and made serviceable. 15. dispensing hose nozzles and fittings are to be checked and are to be made serviceable. 16. straightness and structural integrity of bar is to be checked and same is to be rectified if required. 17. all the moving parts are to be lubricated with correct grade of lubes/greases. 18. conduct ndt if required for stress crack detection. 19. cleaning of equipment is to be done before and after servicing. 20. service status and next due date is to be tagged. 21. summary report is to be given to the user after repair of all the repairing work done. 22. adhere to oem servicing guidelines and intervals. 23. use of oem grade consumables and spare parts.