Get complete information related to latest Crown Shaft Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Crown Shaft Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Crown Shaft Tenders.
Tender For corrigendum : procurement of ht switchgear spares - busbar support insulators 95mm, busbar support insulators 75mm, fixed and moving contact 3f, moving contact for 1600a, htswg 47 motor cut-off limit switch, coupling rod for vm12 vcb, swing bolt for vm12 breaker, auxiliary rod for vm12 breaker, damping rubber pad for vm12 breaker, set of pins for vm12 breaker, bolt for truck wheel for vm12 breaker, set of clips for vm12 breaker, rollers for vm12 breaker, bearing for vm12 breaker, flexible connection for 1250a- 1600a for vm12 breaker, packer cu for vm12 breaker, rack in rack out handle for vm12 breaker, auxillary switches 16 ways for vm12 breaker, compression spring for vm12 , support rod for vm12 breaker, spacer tube for vm12 breaker, centering ring for vm12 breaker, spherical rod end for vm12 breaker, tripping unit assembly vm12 breaker, closing unit assembly for vm12 breaker, pole terminal for vm12 breaker, vm12 breaker wheel, trip latch pawl, trip latch roller, trip latch roller lever, pole operating lever, shaft drive lever , linkage for indicator, interlock linkage for vm12, spring charging shaft, terminal clamp of vm12 breaker, emergency trip assembly, tripping spring operatinglever, operating mechanism lever, trip dash pot, cam disc for vm12 breaker, spring charging gear box, pole support bottom, breaker shaft , moving contact stem for vm12, drive lever, counter, tripping spring, breaker on-off indicator, spring charging indicator for vm12 vaccum , closing spring
Tender For supply of machinery spares to all the factories of tantea - machinery spares - ctc, 21 teeth pinion shaft for sennova ctc gear box, 45 - teeth gear wheel shaft for sennova ctc gear box, 40 - teeth gear wheel shaft for sennova ctc gear box, high speed - housing block for sennova ctc, slow speed - housing block for sennova ctc, uj cross (srmt make) rll 793 type 47mm x 134mm (big cup), uj cross (srmt make) rll 790 type (small cup), uj cross 39.69 mm x 115.65 mm, uj cross 34.94 mm x 125 mm, propeller shaft - for sennova ctc, clutch shoe - for sennova ctc, movable jaw - for sennova ctc, fixed jaw - for sennova ctc, housing block axil spring - for sennova ctc, de-jamming - spring - for sennova ctc, mandrel adaptor with ring - for sennova ctc, mandrel end cap - for sennova ctc, conveyor drive v- pulley- for sennova ctc, gear box - adopter - for sennova ctc, gear box - adopter with combined- for sennova ctc, ss segments for 13" dia x 2" width (is 304 grade), roller bearing sleeve for kaizen super ctc machine 63.1 mm, bearing size 69.95, length 44 mm with m6 allen screw, roller bearing sleeve for kaizen super ctc machine 63.1 mm, bearing size 69.95, length 48 mm with m6 allen screw, clutch fixed jaw for keizen super ctc, clutch moveable jaw for keizen super ctc, gear box input shaft for keizen super ctc, roller bearing sleeve for sennova ctc, gun metal bush big for sennova ctc, gun metal bush small for sennova ctc, conveyor roller drum for sennova ctc - top and bottom, cam housing rh, cam housing lh, de-jamming lever 2" spring plate, micro dial assembly for sennova ctc, micro ball for sennova ctc, scraper spring for sennova ctc, clutch bracket with 6 mm bush, micro dial assembly for innova ctc, propeller shaft for innova ctc, mandrel adaptor for innova ctc, gear box adopter for innova ctc, clutch jaw (fixed and moving for innova ctc), clutch shoe - for innova ctc, high speed - housing block for innova ctc, slow speed - housing block for innova ctc, 7" od x 4c - civ pulley, 7 1/2" od x 4c - civ pulley, housing block for ctc( gem make), roller adopter for ctc gem make, roller end cup for ctc gem make, roller end cup with sprocket for ctc gem make, housing block for ctc(keizen super make), roller adopter for ctc (keizen super make), roller end cup for ctc keizen super make, gear box input shaft (t&i ctc keizen super), gear box input shaft (t&i ctc keizen nova), gear box input shaft (gem ctc ), gear box input shaft (mesco ctc ), drier, teflon bellow for kilburn drier ee model big size, teflon bellow for kilburn drier ee model small size, teflon bellow for kilnburn drier ff model 5500 mm x 250 mm x endless, gi tray 6 for tempest drier, gi tray 4 for tempest drier, tray carrying chain link small pin for tempest drier, drier chain link, 1 1/4" ms f bearing square, spring flat for kilburn drier, teflon bellow 250 mm width x 5240 mm endless, teflon bellow 250 mm width x 5250 mm endless, teflon bellow 5500 mm x 290 mm x endless, teflon bellow 4000 mm x 250 mm x endless, teflon bellow 4400 mm x 250 mm x endless, teflon bellow 5250 mm x 250 mm x endless, heater, c.i tube bank for 18 cm parucco heater, c.i fire bar for 18 cm parucco heater, c.i side tile lh & rh for 18 cm parucco heater, c.i centre tile for 18 cm parucco heater, c.i out side upper back plate lh & rh for 18 cm parucco heater, c.i inner side upper back plate lh & rh for 18 cm parucco heater, c.i lower back plate lh and rh for 18 cm parucco heater, c.i lower back plate centre for 18 cm parucco heater, c.i flue division plate lh & rh for 18 cm parucco heater, c.i upper centre back curved plate, ci fire bar for tea master heater- 18 cm, ci tube banks for tea master heater -18 cm, ms tube bank set for 18 cm parucco heater, ci fire bar for 33", rotor vane, coupling flange on shaft side (for 18" rotor vane), coupling flange on shaft side (for 18" rotor vane), coupling flange on gear box side side (for 15" rotor vane), coupling flange on shaft side (for 15" rotor van
Tender For tender for supply of enq no 22 spares for tata tpr meak mico bosch : : - hydraulic head , vane pump , drive shaft , compression spring , roller , roller pin , pressure control valve , cam plate , t d piston , gasket for t d piston , gasket for t d piston , service kit , temprature sensor , nozzle (dsla 142p 1501) , nozzle washer , overflow valve , trox screw for supply pump
Tender For supply of mt spares f f - oil filter , rear brake shoe , cam shaft , field coil assy , armature 12v , rectifier , regulator , nut bolt 17 no , roller brake shaft , oil seal transfer case , brake booster diaphram , washer motor , transfer case stud , wiper relay , temp gauge , cam plate , roler with pin , pressure switch assy , fan belt
Tender For supply of spares for bottom ash handling system of ash plant - unit no.3, 4 & 5 at gandhinagar tps. - shoulder bolt with lock plate for assembling part no.8 (part no.9) for 24" x 24" feed gate assembly of bottom ash system unit- 3 and 4 as per dwg. no. 8743-2b-571., cross brace (part no.11) for 24" x 24" feed gate assembly of bottom ash system unit- 3 and 4 as per dwg. no. 8743-2b-571., resilient gate face p.no-2,for bottom ash hopper,drg 8743/2b/571, shoulder bolt with lock plate for assemblying part no.8 (part no.9) of 24x24 squire bottom feed gate dwg.no. 95p10-t-2b-570 of unit no. 5, cross brace (part no.11) of 24x24 squire bottom feed gate dwg.no. 95p10-t-2b-570 of unit no. 5, gate face 1 set consists of ss:316 gate face with m.s back up plate of 24x24 squire bottom feed gate of unit no. 5, cam segment p.no-1 for 33"x30 excen crusher, front wear plate/anvil plate of 33" x 30" clinker crusher / grinder assembly for unit-3and4 (1 set equals to 3 nos.)., back wear plate/plate combing (part no. 6) of 33" x 30" clinker crusher / grinder assembly as per dwg. no. 8743-2b-582(rev-1) for unit-3 and 4 (1 set equals to 3 nos.)., side wear plate(part no. 8) of 33" x 30" clinker crusher / grinder assembly as per dwg. no. 8743-2b-582(rev-1) for unit-3 and 4 (1 set equals to 2 nos. left hand and 2 nos. right hand wear plate)., shaft with shaft structure and shaft sleeve of 33" x 30" clinker crusher / grinder assembly for unit-3 and 4., 33"x30" single roll clinker crusher / grinder complete assembly without drive arrangement, fluid coupling, chain drive and driven sprocket as per dwg. no.8743-2b-582(rev-1) for unit-3and4, feedsump below clinker crusher for unit no.3 and 4, roll (cam segment) 1 setequals to 8 nos. cam segment of single roll crusher for unit no. 5, front wear plate/anvil plate (part no.3) 1 set consists of 3 nos b front wear plate of single roll crusher dwg.no.95p10-2b-582 (rev-1) for unit no. 5, back wear plate/plate combing (part no.6) 1 set consists of 3 nos back wear plate of single roll crusher dwg.no.95p10-2b-582 (rev-1) for unit no. 5, side wear plate (part no.8) 1 set consists of 2 nos. left hand and 2 nos right hand type of single roll crusher dwg.no.95p10-2b-582 (rev-1) for unit no. 5, shaft with shaft structure with shaft sleeve(part no.2 and15)for clinker grinder., bearing support (part no.8) of single roll crusher dwg.no.95p10-2b-582 (rev-1) for unit no. 5, single roll crusher complete assembly without drive arrangement,fluid coupling,chain,drive and driven sprocket of single roll crusher dwg.no.95p10-2b-582 (rev-1) for unit no. 5, feed sump of bottom ash system of unit - 5 as per drawing no. 95p10 - t - 1b - 711, complete assembly of feed gate housing with feedgate, access door for unit no.3 and 4, bearing housing of dcips make 33" x 30" clinker crusher/grinder, locking plate for 600 dia. round access door for bottom ash hopper, nozzle with ceramic tip(part no. 2)tip size- 36 mm of 8" jet pulsion pump assembly for bottom ash system of unit-3 and 4 as per dwg.no.8743 - 2b - 591(rev-1), aligning ring(part no. 10)of 8" jet pulsion pump assembly for bottom ash system of unit-3 and 4 as per dwg.no.8743 - 2b - 591(rev-1), half clamp(part no. 11)of 8" jet pulsion pump assembly for bottom ash system of unit-3 and 4 as per dwg.no.8743 - 2b - 591(rev-1) 1 set equals to 2 nos., 9" flange clamp half (part no. 18) of 8" jet pulsion pump assembly for bottom ash system of unit-3 and 4 as per dwg.no.8743 - 2b - 591(rev-1) 1 set equals to 2 nos., 8" jet pulsion pump complete assembly without tail pipe for bottom ash system of unit-3 and 4 as per dwg.no.8743 - 2b - 591(rev-1), nozzle with ceramic tip size 34 mm of jet pump for b.a system dwg.no. 95p10-2b-591 (rev-1) for unit no. 5, aligning ring (part no.10) of jet pump for b.a system dwg.no. 95p10-2b-591 (rev-1) for unit no. 5, half clamp (part no.11) 1 setequals to 2 nos of jet pump for b.a system dwg.no. 95p10-2b-591 (rev-1) for unit no. 5, 9" flange clamp half (part no