Latest dc motor drive Tenders | Government dc motor drive Tenders

CTN :45696133

13 Jul, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for electronics and communication engineering department - supply of equipment for electronics and cmmunication engineering department, 8051 micro controller kit :specification : operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., temperaturemeasurementkitspecification : sensors:rtd (pt-100), thermocouple (fe-k/j-type), and/orthermistor (ntc). display: 3 digit led/lcd digital display(typically 200 mv fsd). temperature source: portable water kettle orheater block. signal conditioning: on-board circuitry foramplification, linearization, and cold junctioncompensation. test points: multiple 2 mm / 4 mm banana socketsfor monitoring input/output signals. power supply: 230 v ac, 50 hz, single-phase. accessories: glass thermometer, 10 k ntcthermistor probe, k-type thermocouple probe,patch cords and user manual., ask modulationanddemodulation kit:specification : message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz,amplitude 5 v. modulator type: switching modulator using analogswitch / transistor switching ic. demodulator: envelope detector and lpf. comparator: lm311 based. supply voltage (board): +12 v, +5 v dc. supply current: 100 ma minimum. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., dth trainer kit:specification :power supply: 200 v to 240 v ac, 50 hz.dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter): input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency:tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m.controls: channel selection. volume control.fault simulation: five built-in simulated faults for troubleshootingexperiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption.pcb size: 15" 12" with multicolour section-wise blockdiagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna.additional features: dth subscription connection withdoordarshanfree channels. free-to-air channel demonstration., fpga trainer kit:specification : must use industry-standard mid-range fpgadevice usb-jtag programmable, compatible withvivado ise (webpack). power supply: 5 v dc through usb or externaladapter. on-board peripherals: leds, switches, pushbuttons, 7-segment display,clock source, gpio /pmod expansion ports, uart, vga / hdmi, usbuartbridge, usb cable. user manual.

corporations/Associations/Others

CTN :45612179

30 Jun, 2026 NA

Trivandrum - Kerala

Tender For auction sale of unserviceable broken spring leaves,unserviceable clutch disc,unserviceable axle shaft..,unserviceable wheel disc,unserviceable gearbox case, t cover, fly wheel, side cover,etc,unserviceable fire extinguisher,unserviceable diesel tank & air tank,unserviceable frnt & rear brake drum.,unserviceable frnt & rear brake chambers,unserviceable armatures, rotor assys,starter bodies,etc,unserviceable electrical motor assy, ceiling fans, etc,unserviceable steel scrap: king pins, spring shackle pins,etc,unserviceable led destination pannel 6 feet,unserviceable led destination pannel 3 feet,unserviceable gear wheels, main shafts,counter shafts, etc,unserviceable bearings of all types withleeves, etc,unserviceable cylinder liners and broker liners.,unserviceable crown & pinion spares, etc,unserviceable items: head lights, rreflectors, switches, etc,unserviceable slackers, joint flangers, boot brackets,etc,unserviceable lowfloor volvo seat frames with cushions and without cushions,unserviceable rubber items: glass bedings and lock beedings, etc

CTN :45519945

22 Jun, 2026 37.35 Lacs

Chhabra - Rajasthan

Tender For requirement of spares of m/s ingersoll rand make conveying air compressor model r-160i-x 7.5wc and up5-22-7 for dry fly ash dense phase system,unit#3 and 4, ctpp, chhabra - model no. r160i-x7.5 wc, seal, shaft high pressure part no. 89292445, element, seprator tank 18 inch part no. 23566938/ 23545841, oil cooler, water cooled part no.23572415, after cooler, water-cooled part no.23572423, cap screw m6x25 soc hd cap w/nylon insert part no.22168710, pressure transducer 0-225 psig part no.47545275001, pressure transducer 0-15 psig part no.47560902001, assembly gear set 160 kw single stage 7.5 bar part no.23521859, pin dowel [motor] part no.39194915, pad pre filter part no.23523772, actuator service kit part no.23467251, inlet valve part no.23421217, elbow 1/4" 90 degree straight thread ms part no.96757604, spacer gear (ce177g) part no.39326483, sleeve motor shaft 4.25 od m132/160 part no.89292478, key,square both ends 0.88sq x1.25 part no.95135638, valve in line check part no.23453020, tube gear case scavenge part no.23453129, air cleaner assembly nlg37-42 pico standard part no.23390156, ultra coolant (208 litres) drum part no.39433743, key, rect one round end part no.96759212, clamp, plate part no.35295336, screw, socket head part no.32555819, housing, seal part no.22880744, gasket, gear case part no.39454558, pin, dowal [air end] part no.35295336, valve, orifice [separator tank] part no.23449200, oil filter assembly part no.23523434, o ring set part no.ok002222, pressure transducer cable part no.23529373, temprature sensor part no.23522246, valve min press check 132-160 kw part no.23521297, 5sv solinied cable part no.23562432, model no. up5-22-7, element coolant filter part no.54672654, element seprator 194cfm (spin-on) part no.54749247, pad pre filter part no.22053722, element air filter part no.89295976, kit, inlet valve repair part no.22067177, kit-mpcv part no.22064695, kit thermal valve repair part no.22393326/ 22832885, valve solenoid 125 inch npt part no.54774302, valve solenoid 1/2 in npt 110 volt part no.54654652, spring gas part no.54749114, elbow .31tx .50sae part no.95993572, elbow , 90deg male 37a10c3xz2 part no.95937686, tube oil feed (rear bearing) part no.85581858, tube, vmc block to bare part no.85581866, belt part no.89265052, ultra coolant (20litres) drum part no.38459582, tempreture sensor part no.22137848, conteroller part no.22128763, tube nylon part no.39124813, tube nylon part no.39124821, elbow part no.39155650, elbow part no.39155577, nipple part no.22354989

CTN :45501064

02 Jul, 2026 20.00 Lacs

Bikaner - Rajasthan

Tender For notice inviting limited tendernotice no: 01/elect./2026/ 706 date:- 10.06.2026tools & equipments of –electrician trade- heavy duty screwdriver insulated , electrician screwdriver thin stem insulated handle, , knife double bladed electrician, , chisel firmer with wooden handle, , grease gun, , (a) crimping tool, , wire cutter and stripper, , hacksaw frame, , tweezers, , drill hand brace, , plane cutters, , smoothing cutters, , file flat rough, , file flat bastard, , file rasp, half round, , the soldering gun, , contactor & auxiliary contacts (rm), , contactor & auxiliary contacts. (rm), , pin type, shackle type, egg type & suspension type insulators including hardware fitting, , portable electric drill machine, , load bank (lamp/heater type), , brake test arrangement with two spring balance rating, , laboratory type induction coil, , series test lamp (rm), , knife switch dpdt fitted with fuse terminals (rm), , knife switch tpdt fitted with fuse terminals (rm), , miniature circuit breaker (rm), , earth plate (rm), , earth electrode (rm), , elcb and rccb (rm), , fuses (rm), , rheostat (sliding type), , capacitors (rm), , various electronic components (rm), , various lamps (rm), , plug socket piano switch lamp, , holder (rm), , cables:, , twisted pair, , non-metallic sheathed cable, , underground feeder cable, , ribbon cable, , metallic sheathed cable multi-, , conductor cable coaxial cable, , direct-buried cable (rm), , rubber mat (rm), , electrician helmet, , rcc pole with accessories (ms angle iron, 'c' clamp, stay insulator etc.) and materials, , quipment, , ohm meter; series type & shunt type, portable box type, , digital multi meter, , a.c. voltmeter m.i. analog, portable box type housed in bakelite case, , milli voltmeter centre zero analog, portable box type housed in bakelite case, , ammeter mc analog, portable box type housed in bakelite case, , ac ammeter mi, analog, portable box type housed in bakelite case, , weight wattmeter analog, , (b) frequency meter (digital), , magnetic flux meter, , tachometer, , tong tester / clamp meter, , megger, , single phase variable auto transformer, , growler, , ac starters: :- -, , f. star delta starter soft starter, , g. auto transformer type, , oscilloscope dual trace, , function generator, , discrete component trainer, , linear i.c. trainer, , digital i.c. trainer, , domestic appliances -, , g. mixture & grinder, , h. washing machine semi-automatic, , i. motor pump set, , oil testing kit, , battery charger, , current transformer, , potential transformer, , 1 5 or 17 computer or latest version, , d.c. shunt generator with control panel, , motor-generator (ac to dc) with control panel, , d.c. compound generator with control panel including fitted rheostat, voltmeter, ammeter and breaker, , dc series motor coupled with spring balance load with control pannel, , dc shunt motor with control pannel, , dc shunt motor with control pannel, , dc compound motor with starter and switch with control pannel, , motor generator(dc to ac) set consisting of - shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed, , plate, fixing bolts, foundation bolts and flexible coupling., , ac squirrel cage motor with star delta starter and triple pole iron clad switch fuse with mechanical load., , ac phase-wound slip ring motor with starter switch, , universal motor with starter/switch, , synchronous motor with accessories like starter, excitation arrangements., , thyristor /igbt controlled d.c., , motor drive with tacho-generator feedback arrangement, , thyristor/igbt controlled a.c. motor drive with, , single phase transformer, core type, air cooled, , three phase transformer, shell type oil cooled with delta/ star, , electrical machine trainer -, , diesel generator set with changeover switch, ov

CTN :45430786

18 Jun, 2026 NA

Ariyalur - Tamil Nadu

Tender For supply of electronics andcommunication engineering lab materials - electronics and communication engineering lab materials, dso (digital storage oscilloscope)bandwidth: 50 - 100 mhz.sampling rate: 1gs/s.channels: 2 (minimum)power supply: 100v 240v ac, 50-60 hzautomatic measurement: vpp, vavg,rms, frequency, period, vmax, vmin, rise time, fall time, + width, - width, +duty, - duty etc.,horizontal scale: 5 ns/div 100 ns/div or equivalentvertical resolution: 8 bits (2 channels simultaneously)vertical sensitivity: 1 mv/div 10 v/div (at input)waveform math: +, -, x , , invert, fft etc.,waveform storage: 16 waveforms or equivalentcommunication interface: usb host, usb interface.7-inch color display or equivalentbasic trigger functions, digital ic trainer kit with breadboard5v dc, 1a regulated power supply 12v dc / 15v, 200 ma regulated power supplysolderless breadboard to accommodate 8 16-pin icszif (zero insertion force) ic socketssupports ttl and cmos icslogic io leds for output monitoring8 buffered led outputs8 debounced switch inputsttl clock: 1 mhzvariable clock generator: 0.5 hz to 50 hzsingle pulse output: 100 ms (buffered, positive and negative outputs)one seven-segment display with 4 bcd inputsbuilt-in logic probesbuilt-in logic switchesexperiments on basic logic gates, flip-flops, counters, and multiplexers, eliminator transformer (stepdown)input - 220v - 240v ac, 50 hz, output-2v to 12v dc, 0-2 a ripple: 5mv, decade resistance boxrange: 1 to 10 m , steps: 1-10-100-1k-10k, accuracy 1%, suitable for filter and oscillator experiments, decade inductance boxrange: 1 h to 10 h, rotary switch selection, low loss inductors, accuracy 1%, , suitable for filter and oscillator experiments, 8051 micro controller kitoperating voltage: +5v dc4 kb flash (at89c51) / 8 kb flash (at89s52)ram: 128 bytes internal ram16 2 alphanumeric lcdpush buttons / tactile switchesdip switches for digital inputinbuilt adc interface : ldr,potinbuilt dac interfaceinbuilt stepper motor driver with stepper motorinbuilt dc motor driver with dc motor1x4 led array, 1 x4 keypad, 1x relay1x buzzer, 16x2 lcd display, 1x pwm driver1x hardware interrupt key, inbuilt rtcinbuilt eeprom, inbuilt uart module4x7 segment display, both assembly and c language programmable, pc interfaceable., single phase induction motorsingle phase induction motor, 230v ac, 50hz supply.power rating 1 hp (0.75 kw).speed 1440 rpm.capacitor start/run type suitable for lab useloading setup portable ammeter and digital tactometer contact type, auto transformerinput - single-phase, 230v/240v, 50 hz, 4a, ac output - 0 to 270vac, class "h" or class f insulation., temperature measurement kitsensors: rtd (pt-100), thermocouple (fe-k/j-type), and/or thermistor (ntc).display: 3 digit led/lcd digital display (typically 200mv fsd).temperature source: portable water kettle or heater block.signal conditioning: on-board circuitry for amplification, linearization, and cold junction compensation. test points: multiple 2mm/4mm banana sockets for monitoring input/output signals.power supply: 230v ac, 50hz, single-phase.accessories: includes a glass thermometer, ntc thermistor probe 10k, k-type thermocouple probe, patch cords, and instruction manual., ask modulation and demodulation kitmessage signal 1 : 8 bit variable data, amplitude 5vmessage signal 2 : debounce data, amplitude low (0) & high (5v)message signal 3 :fixed data 25k, 12.5k, 6.25k, 3.12k, amplitude 5vcarrier signal : sine wave frequency 200 khz, amplitude 5vmodulator type : switching icdemodulator : envelope detector & lpfcomparator : lm 311 basedsupply voltage (board) : +12v, +5v / dcsupply current : 100 ma (minimum)input voltage : 230 v/ 50 hz acinterface connectors : 2mm banana socket, dth trainer kitpower supply 200v to 240v ac, 50hz,dish antenna 1.5 aluminum steerable, lnb low noise block down converterinput frequency ku band.output frequency 950 to 1450 mhz.conversion gain 65 db.noise temp 35 degree k max.set top box receiver in traine

corporations/Associations/Others

CTN :45451225

15 Jun, 2026 NA

Trivandrum - Kerala

Tender For auction sale of unserviceable broken spring leaves,unserviceable clutch disc,unserviceable axle shaft..,unserviceable engine block,unserviceable wheel disc,unserviceable gearbox case, t cover, fly wheel, side cover,etc,unserviceable fire extinguisher,unserviceable diesel tank & air tank,unserviceable frnt & rear brake drum.,unserviceable frnt & rear brake chambers,unserviceable armatures, rotor assys,starter bodies,etc,unserviceable electrical motor assy, ceiling fans, etc,unserviceable engine assy,unserviceable steel scrap: king pins, spring shackle pins,etc,unserviceable led destination pannel 6 feet,unserviceable led destination pannel 3 feet,unserviceable gear wheels, main shafts,counter shafts, etc,unserviceable bearings of all types withleeves, etc,unserviceable cylinder liners and broker liners.,unserviceable crown & pinion spares, etc,unserviceable items: head lights, rreflectors, switches, etc,unserviceable slackers, joint flangers, boot brackets,etc,unserviceable lowfloor volvo seat frames with cushions and without cushions,unserviceable rubber items: glass bedings and lock beedings, etc

Central Government/Public Sector

CTN :45431581

09 Jun, 2026 NA

Multi City - Gujarat

Tender For auction sale of depot ferrous scrap - 98050114 scrap signaling, p way and ohe items, c & w items- ms, gi,ci containing signaling units, rods, ms, gi structures, ladders, mast, etc. and all other types of signaling items, gear case, the ground connection, ohe fitting,ms chains, heavy structure almirah/racks, rods angle, channel, pipes, lc material, ladders, jali, pantograph with or without pneumatic motor, gate, door, tie bar, fencing, trolley, ms machines etc., tmt bars rods, pulley, angle , rib cage, wagon body cut piece bogies side frame, machines, st sleeper, ms sheet,various types sleeper part, tie bar, fencing bars, i-beam empty drums, light fittings, rail pieces, ms wires,showel, bush for brake rigging, angular ring , end plate for axle box, axle end cap for wap, axle box, grill- jali, cabinet frames, rack ballast, rusted body and parts of weighing machine, electronic/electrical material, small rods angle, battery boxes, tool boxes, shovel, rail door handles, main door, foot plate, step plates, bench pipes, typewriter g.i. pipes, trolleys, water tank bond, location box with or without their component and wiring fittings, trolly, different type of ohe bonds of rail and other various ms fabricated structures, break load rings, pins, screw, bolts, spikes, keys, loco parts, stay rods, sleeve for centre pivot, pantograph parts, palm pull rods, lever, axle box housings, air motor, springs of pantograph, connecting rods, and other rods, rear cover of axle box housing, longer hanger, spare parts of spt machine, pipe fittings, end shield covers, break beam hangers, brake shoe, vertical lever, suspension levers, compressor spares, tension rods bushes, dash pots,angle, bond, location box with or without their component and wiring fittings, trolly, diffrent type of ohe band of rail and other various ms fabricated structures of sorts and sizes with or without parts fittings miscellaneous items, etc. and non-ferrous attachments, unserviceable.

Central Government/Public Sector

CTN :45431584

09 Jun, 2026 NA

Multi City - Gujarat

Tender For auction sale of depot ferrous scrap - 98050114 scrap release all types of railway ferrous material consisting of s&t, p way, works and ohe items c & w items- such as ms, gi, ci containing signalling units, rods, junction boxes, panels, ms gi structures, ladders, mast, rtu, cb, etc. and all other types of signaling items, gear case, the ground connection, ohe fitting, ms chains, heavy structure almirah/racks, rods angle, top housing, road bar, glude joint, ground connection channel, pipes, lc material, ladders, jali, spring plank, pantograph with or without pneumatic motor, gate, door, brake cylinder, tie bar, fencing, trolley, ms machines etc., tmt bars rods, pulley, rib cage, point machines without motors, wagon body cut piece bogies side frame, machines, sleeper, ms sheet, various types sleeper part, tie bar, fencing bars, i-beam, damaged empty drums, light fittings, rail & rail pieces, ms wires, junk light weight/corroded material consist of toughened sheets, m.s./gi sheets, grease seal, drum, wire, parts of rolling shutter, light weight cuttings, various damaged and rusty drums filled with coalter, dry paint, mud and dray fo if any of sort and sizes, g.i. buckets, steel buckets baskets, signal lamps, duct, vent pcs., fencing and pipes, wire mesh, stretcher, bicycle, pan, frames, electrical fittings, t.l. fittings, grill- jali, cabinet frames, rack ballast, rusted body and parts of weighing machine, electronic/electrical material, small rods angle, battery boxes, tool boxes, shovel, rail door handles, main door, foot plate, step plates, bench pipes, typewriter g.i. pipes, trolleys, water tank bond, location box with or without their component and wiring fittings, trolly, different type of ohe bonds of rail and other various ms fabricated structures, break load rings, pins, screw, bolts, spikes, keys, loco parts, stay rods, sleeve for centre pivot, pantograph parts, palm pull rods, lever, axle box housings, air motor, springs of pantograph, connecting rods, and other rods, rear cover of axle box housing, longer hanger, spare parts of spt machine, pipe fittings, end shield covers, break beam hangers, brake shoe, vertical lever, suspension levers, compressor spares, tension rods bushes, dash pots, ms& wi turning borings cut, collars, vehicle spares, ci items consisting of rusty and dusty drainage pipe, valve, meter, brake block, pulley, motors body, pipes, plates, d.v, vacuum cylinder chamber, pig irons pieces, signaling box ohe fittings, steel furniture consisting of chairs, tables, g.i. separation sheet, chair , stretcher, beds, ms rack, almira, other types of steel furniture of sorts and sizes, broken, damaged with or without wood, cushions, plastic, mica, foam seat attachment, parts brake liner, thrust bearing, spring, yoke, insulation block hangers, slides, locking rods, parts of point machine, a b cover, break head, cylinder head, pcs. of break beam, protective tubes, and other p-way fittings, coupler, knuckles, cp top/bottom, pu pad, narrow/wide jaw adapter, released bulk head components, wagon doors, cutting plate, and assorted cut pieces thereof, fabricated from irsm 44, etc. brake cylinder, cs & ci if any. valve, broken pcs. of bearings, inner and outer race of bearings, spares of break valve, trolley wheels, clamps, bmbc parts, pump shafts, impellers, tension device parts, fan armatures, chain sling, rev. center, hooks, spares of trucks, accessories of transformer, fish plates, hooks, silent blocks, cut pieces of plates, doors, angles, etc., all plastic items, rubber and wooden , fasteners such as bolts, nuts, and other related misc, etc., with or without, rail, of sorts and sizes with or without parts fittings and minor non-ferrous attachments, unserviceable. excluding items - railway track. remarks:the quantity estimation is based on visual observation and is indicative only. the lot has been prepared to clear the land before handing over the scrap yard for memu work. 2. loading will be allowed

CTN :45404144

09 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for electronics and communication engineering department - supply of equipment for electronics and cmmunication engineering department, 8051 micro controller kit :specification : operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., temperaturemeasurementkitspecification : sensors:rtd (pt-100), thermocouple (fe-k/j-type), and/orthermistor (ntc). display: 3 digit led/lcd digital display(typically 200 mv fsd). temperature source: portable water kettle orheater block. signal conditioning: on-board circuitry foramplification, linearization, and cold junctioncompensation. test points: multiple 2 mm / 4 mm banana socketsfor monitoring input/output signals. power supply: 230 v ac, 50 hz, single-phase. accessories: glass thermometer, 10 k ntcthermistor probe, k-type thermocouple probe,patch cords and user manual., ask modulationanddemodulation kit:specification : message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz,amplitude 5 v. modulator type: switching modulator using analogswitch / transistor switching ic. demodulator: envelope detector and lpf. comparator: lm311 based. supply voltage (board): +12 v, +5 v dc. supply current: 100 ma minimum. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., dth trainer kit:specification :power supply: 200 v to 240 v ac, 50 hz.dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter): input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency:tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m.controls: channel selection. volume control.fault simulation: five built-in simulated faults for troubleshootingexperiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption.pcb size: 15" 12" with multicolour section-wise blockdiagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna.additional features: dth subscription connection withdoordarshanfree channels. free-to-air channel demonstration., fpga trainer kit:specification : must use industry-standard mid-range fpgadevice usb-jtag programmable, compatible withvivado ise (webpack). power supply: 5 v dc through usb or externaladapter. on-board peripherals: leds, switches, pushbuttons, 7-segment display,clock source, gpio /pmod expansion ports, uart, vga / hdmi, usbuartbridge, usb cable. user manual.

CTN :45365476

13 Jun, 2026 NA

Tuticorin - Tamil Nadu

Tender For purchase of lab equipments for ece dept - purchase of lab equipments for ece dept, dc voltmeter (digital) (item code : c006) 1.dcvoltmeteranalog moving coil -(0-10)v, class1.0( 1%full- scale)accuracy - 5 nos2.dcvoltmeteranalog- movingcoil-(0-30)v, class1.0( 1%full-scale)accuracy - 4nos, dc ammeter(item code : c007)specifications: 1. dcammeteranalog movingcoil- (0-30)ma,. 5 nos2. dcammeteranalog -movingcoil -(0-1000) a, class 1.0 ( 1 % full-scale) accuracy - 5 nos, decade capacitance box(item code : c0011)specifications: range: 100 pf to 100 f rotary switch selection with 6 dials. maximum voltage: 350 v. accuracy: 1%., decade inductance box(item code : c0012specifications: range:10 hto10h. rotaryswitchselectionwith6dials. low-lossinductors. accuracy: 1%., 8051 microcontroller kit(item code : c0013)specifications: operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., embedded trainer kit (using lpc2148) (item code : c0014)specifications: cpu - lpc2148, core - 16/32 bit arm7tdmi-s speed - max 60 mhz, flash - 512kb, ram (on chip) 40kb, 46 general purpose i/opins, usb2.0 one 10bit a/d converter with 14 analog inputs, one 10bit d/a converter, six pwm & watchdog two uarts (16c550), two i2c (400kb/s), two spi eight bit digital output, eight bit digital input,16x2 characters lcd and 4x4 matrixkeypad one potentiometer for giving analog input, relay & buzzer interface i2c devices: rtc, eeprom and seven segment display, on board stepper motordriver lm35 temperature sensor, one rs 232 lines are terminated at 9 pin d type connector and usb interface board has inbuilt power supply and mounted in sturdy cabinet accessories usb cable with utility software to download programs from pc to target board power cord, user manual, temperature measurement kit (item code : c0019)specifications: sensors: rtd (pt-100), thermocouple (fe-k/j-type), and/or thermistor (ntc). display: 3 digit led/lcd digital display (typically 200 mv fsd). temperature source: portable water kettle or heater block. signal conditioning: on-board circuitry for amplification, linearization, and cold junction compensation. test points: multiple 2 mm / 4 mm banana sockets for monitoring input/output signals. power supply: 230 v ac, 50 hz, single-phase. accessories: glass thermometer, 10 k ntc thermistor probe, k-type thermocouple probe, patch cords and user manual., fpga trainer kit(item code : c0025)specifications: must use industry-standard mid-range fpga device usb-jtag programmable, compatible with vivado ise (webpack). power supply: 5 v dc through usb or external adapter. on-board peripherals: leds, switches, push buttons, 7-segment display,clock source, gpio / pmod expansion ports, uart, vga / hdmi, usb uart bridge, usb cable. user manual.

Dc Motor Drive Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

corporations/Associations/Others

corporations/Associations/Others

Central Government/Public Sector

Central Government/Public Sector