Get complete information related to latest Diesel Loco Spares Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Diesel Loco Spares Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Diesel Loco Spares Tenders.
Tender For supply of oil filter for tata jd , fuel filter for tata jd , hyd filter for tata jd , inner and outer element for tata jd , air pre cleaner for tata jd , dashboard switch for tata jd , temp sensor for tata jd , fan belt for tata jd , gear slow nut for tata jd , starting hyd hose pipe for tata jd , cross for tata jd , 4x4 shaft for tata jd , stopper cable for tata jd , accelerator cable for tata jd , door handle with lock for tata jd , wiper with accessories for tata jd , grease nipple for tata jd , head light bulb for tata jd , bucket teeth with lock for tata jd , cabin fan for tata jd , trans filter for tata jd , wire tie packet for tata jd , hyd jack seal for tata jd , excavator hyd hose for tata jd , main fuel line for tata jd , fuel tank strainer for tata jd , fuze for tata jd , rear indicator for tata jd , m seal small for tata jd , fuel filter for size dozer-ii , oil filter for size dozer-ii , cotton filter for size dozer-ii , air cleaner inner and outer for size dozer-ii , blade pin arm lock for size dozer-ii , hyd filter for size dozer-ii , fan blade for size dozer-ii , fuel filter for air compressor , oil filter for air compressor , air cleaner inner and outer for air compressor , rear indicator for ssl bobcat , oil filter for ssl bobcat , fuel filter for ssl bobcat , hyd filter for ssl bobcat , horn 12v for ssl bobcat , starting relay for ssl bobcat , oil filter for multi purpose tractor , fuel filter for multi purpose tractor , hyd filter for multi purpose tractor , horn for multi purpose tractor , ignition switch for multi purpose tractor , hyd hose for multi purpose tractor , side indicator for multi purpose tractor ) /bid number : gem/2025/b/7021868 * /dated: 19-12-2025 & & / bid document 1 / 40
Tender For supply of weather strip , crank oil seal rear , rectifier plate , regulator sr 60 , cylinder head gasket , timing belt tensioner , timing belt , i c motor , water pump assy , propeller shaft uj cross , steering gear box repair kit , pully tff , door beading lh , door beading rh , speedometer head , transfer case mounting bracket , brake shoe lock , tff air pressure pipe
Tender For supply installation and commissioning of lab. equipment for civil engg dept - digital compression testing machine with capacity of 3000kn (300 tons) with flexural attachment of 100kn capacity including accessories and toolkitspecification:-1. machine capacity required : - digital compression testing machine with capacity of 3000kn (300 tons) with flexural attachment of 100kn capacity. digital compression testing machine shall confirm is 516 and is 14858. digital compression testing machine for testing concrete cubes of size 100mm, 150mm, 200mm ,300mm and concrete cylinder specimen up to 300mm diameter and 300mm height . also the cement mortar cubes of 70.7 mm size and 50mm size. 2. loading frame:- steel welded loading frame with top cross head base and solid side walls. hydraulic piston is fixed to the base and platens are hardened, ground and polished. the upper and lower plate should be marked with the guidelines on the lower plate to keep the specimen co-axially with hydraulic jack. the machine should be provided with suitable side spacers as standard to accommodate the variety of sizes of specimens as indicated above. the two speed pump to allow fast approach of platens for daylight closure and also to allow precise control over load application using control lever and valves.3. digital display:- display shall show force and stress values in si units. the electronic control unit shall be based on suitable processor with a built in interface for laptop and computers. the processor speed shall be such that the online load deformation curve on full screen is smooth.4. the storage capacity to record and store 2000 complete test results with the facility of printing results/logged data through built in parallel port. least count of 0.1 kn.5. automatic controls for switch off on overload or over travel or specimen break or manual termination.6. power supply :- suitable for operation on 220v/230v single phase 50hz ac supply 7. additional requirements maximum clearance between plate 400mm. maximum distance between side platen 400 mm platen size 320mm square.8. flexure attachment:- flexure testing machine of 10 tons ( 100kn) capacity confirming to is 516. loading to be applied by the downward movement of piston. machine shall be suitable to test beams of 100x100x500 mm and 150x150x700mm.machine shall be supplied with suitable standard spacers for testing different sizes of beams.9. additional requirement for flexural test: three point loading light weight rugged high strength frame.least count 0.1 kndistance between supporting rollers: - 600mm for 150x150 x700 mm beam and 400mm for 100x100x500 mm beamdistance between loading rollers 200mm for 150x150x700mm beam 133 mm for 100 x 100 x500 mm beam power supply suitable for operation 220v 50hz single phase.10. the machine should be supplied with accurate toolkit11. compatible software should be included