Tender For supply of extension ladder size closed 20ft xextension 50ft , clamp meter , insulation tester 500v to 200m ohms digital model vit 996 , cutting plier make taparia , wire striper 150mm , screw driver 30 cm long make taparia , screw driver set make taparia , electrical rubber hand gloves 11 kv , electrical rubber hand gloves 33 kv , industrial helmet , box spaner set make taparia , double ended spaner set make taparia , ring spaner set make taparia , l key set make taparia , hydraulic crimping tool upto 500 sqmm , discharge rod 11 kv , discharge rod 33 kv , pipe wrench 18inch make taparia , sliding wrench , insulation tape lt , insulation tape ht , carbon terminal cleaner ctc spray , corrosion reaction consultants crc spray , waste cotton , emergency light torch , ht meggar manual 5000 mega ohm make wacko cat part no waco wi5001 kv , hammer make taparia , earth resistance tester 4 terminal 0 to 2000 ohms make waco model no waco r4100 , vernier caliper size 300 mm , inch tape size 05 meters , inch tape size 30 meters , head torch light , fuel pump hand driven , screw gauge digital , laser level multipurpose laser tape
Tender For corrigendum : procurement of lab instruments for chemical lab of ogcd, dtps, htps, kasimpur - sension5 portable conductivitymeter specification range:#conductivity s/cm 0 to 19.99; 200 to 1999#conductivity ms/cm 2 to 19.99; 20 to 199.9#tds: 0 to 50,000 mg/l as nacl salinity: 0 to 42 g/l (ppt)#temperature: -10.0 to 105.0 c#resolution:#conductivity 0.01; 1.0#conductivity ms/cm 0.01; 0.1#tds: 0 .00-199.9 mg/l 0.1mg/l 2 00-1999 mg/l 1 mg/l 2 .00 -19.99 g/l 0.01 g/l 2 0-50 g/l 0.1g/l #salinity: 0.1 g/l (ppt)#temperature: 0.1 c#accuracy:#conductivity: 0.5% in the first 3 ranges, 1% at highest range #td of full scale #salinity: 0.1 ppt (-2 to 35 c) #temperature: 0.1 c# , make-hach, ph meter probe (ph meter sension ph3) cat no-lzw5010t.92.0002 make hachdetails in photograph enclosed in tender document, manual sieves shaker (with sieves set - mesh size-50,+100,+200) any standard make details in photograph enclosed in tender document, centrifugal machine for oil testing, any standard maketube capacity:no.12-24:size 15 mlshould have a digital timerbody should be made of strong fabricated & corrosion resistant steel.control panel- for start/stop switch, dynamic brakes, step less speed regulator with zero start switch & speed indicator with timer and protective fuses.door interlock.maintenance free brushless drive motor with exact speed preselection and display. speed range 100 to3000 rpm and above, accuracy 1 rpm. details in photograph enclosed in tender document, orset appratus (complete set), any standard make details in photograph enclosed in tender document, ph 2700 ph meter specification #ph range -2.000 to 20.000 ph #resolution 0.1 / 0.01 / 0.001 ph #accuracy 0.002 ph + 1 lsd #cal. points up to 6 preset or 5 custom #buffer sets usa, nist, din, user 1, user 2, custom #or range 2000.0 mv #rel. mv range 2000.0 mv on 0.1 mv# accuracy 0.2 mv #temperature,range (meter) 0.0 to 100.0 c / 32.0 to 212.0 f #resolution 0.1 c / 0.1 f #accuracy 0.3 c / 0.5 f #compensation atc / mtc #power requirements 9 v dc adapter, 1.3 a (100/240 vac, smps)# make- eutech
Tender For supply of ferritic steel sheet 8x1250x3000mm., as per drawing: is:6911-1992,grade x04cr1 2 (405), surface finish 2d as per tab. 8., packing instruction: stainless steel sheets, coils an d plates:- (a) stainless steel (austenitic & ferritic steel) coils. the coil shall be protect ed in reasonably good condition to withstand normal handling hazard during transit with the following provision as the barest minimum: i) coil should be wrapped with a la yer of water proof paper through out whole length. ii) coil should be wrapped with a l ayer of biodegradeable sheet. iii) outer & inner of coil should be wrapped with gi sheet . iv) side of the coil should be covered with card board sheet. v) after this whole coil should be wrapped with biodegradeable plastic sheet of suitable thickness. vi) the inne r edge of the coil should be protected by gi ring followed by another iron ring. vii) ou ter edge of the coil should be wrapped with gi ring. viii) coil should be securely strapp ed with minium 5 steel bands through the eyes of the coil and minium 3 steel bands on t he circumference of the eye. ix) whole coil should be mounted on wooden blocks for e asy lifting/stacking. x) the sheets in coil form for thickness 2mm and above shall have: inner dia of coil 450-800mm outer dia of coil 1000-1300mm weight of coil 2.4 - 10 tonnes xi) the sheets in coil form for thickness below 2mm shall have: inner dia of coil 450-650 mm outer dia of coil 1000-1300mm weight of coil 5.0 - 10 tonnes. (b) stainless steel (aust enitic & ferritic steel plates/sheets) i) the sheets/plates shall be supplied in bundles of optimum weight: 2mt+/-10% & each sheet/plate shall be seprated with a layer of water p roof paper, after this the whole bundle should be wrapped with double layer of water proof paper and a biodegradeable plastic sheet of suitable thickness. a metal protecti on in edges should also be provided. ii) all bundles shall have a minimum of 2 hoops upt o 1.2 meter in length and one extra hoop for every additional meter. the bundles shall also be provided with skid (wooden packing under neath) to facilitate handling. mecha nical damange & corrosion during transit if any shall be at the cost of supplier. , procti on procedure: covered in pi [ warranty period: 30 months after the date of delivery ]