Latest digital counter Tenders | Government digital counter Tenders

CTN :45696133

13 Jul, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for electronics and communication engineering department - supply of equipment for electronics and cmmunication engineering department, 8051 micro controller kit :specification : operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., temperaturemeasurementkitspecification : sensors:rtd (pt-100), thermocouple (fe-k/j-type), and/orthermistor (ntc). display: 3 digit led/lcd digital display(typically 200 mv fsd). temperature source: portable water kettle orheater block. signal conditioning: on-board circuitry foramplification, linearization, and cold junctioncompensation. test points: multiple 2 mm / 4 mm banana socketsfor monitoring input/output signals. power supply: 230 v ac, 50 hz, single-phase. accessories: glass thermometer, 10 k ntcthermistor probe, k-type thermocouple probe,patch cords and user manual., ask modulationanddemodulation kit:specification : message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz,amplitude 5 v. modulator type: switching modulator using analogswitch / transistor switching ic. demodulator: envelope detector and lpf. comparator: lm311 based. supply voltage (board): +12 v, +5 v dc. supply current: 100 ma minimum. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., dth trainer kit:specification :power supply: 200 v to 240 v ac, 50 hz.dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter): input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency:tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m.controls: channel selection. volume control.fault simulation: five built-in simulated faults for troubleshootingexperiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption.pcb size: 15" 12" with multicolour section-wise blockdiagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna.additional features: dth subscription connection withdoordarshanfree channels. free-to-air channel demonstration., fpga trainer kit:specification : must use industry-standard mid-range fpgadevice usb-jtag programmable, compatible withvivado ise (webpack). power supply: 5 v dc through usb or externaladapter. on-board peripherals: leds, switches, pushbuttons, 7-segment display,clock source, gpio /pmod expansion ports, uart, vga / hdmi, usbuartbridge, usb cable. user manual.

CTN :45694953

27 Jul, 2026 NA

Multi City - Multi State

Tender For bench top pressure gauge calibrator with accessories- pressure calibration system, maximum no. of pressure module simultaneously, working medium, mode, sensor module range 1, accuracy of sensor module range 1, sensor module range 2, accuracy of sensor module range 2, precision, uncertainty of sensor module range 1, uncertainty of sensor module range 2, measurement modules, control mode, control precision, lowest controllable pressure limit, pressure indication & display system, over pressure protection, leak test & switch test, jog wheel, system mode, valve driver, vacuum pump, contamination prevention system, pressure display units, dc voltage range, dcv resolution, dcv uncertainty, dc current range, dci resolution, dci uncertainty, loop compliance voltage, hart mode, automatic hart detection, hart selectable resistor, write protection, hart commands, remote communication interface hardware, ac power supply, operating temperature range, relative humidity, ingress protection, plumbing lines, fittings and adaptors, warranty, calibration certificatte, test port max. pressure limit, reference port max. pressure limit, vent port max. pressure limit, test port, supply port max pressure limit, liquid or particle filter

corporations/Associations/Others

CTN :45345537

03 Jul, 2026 NA

Hoshangabad - Madhya Pradesh

Tender For corrigendum : supply of proximity switch , reflex sensor size control , gts capacitive proximity switch , proximity switch inductive , solenoid valve , magnet coil for solenoid valve , one way flow control valve , gts pressure regulator , gts pe converter , gts standard socket , power pack i pac , motor cooling fan , motor with encoder , digital input module 8 channels , gts digital output module 8 channel , digital o p module 24 v digital counter , gts analog output assembly , gts positioning modul

CTN :45525479

06 Jul, 2026 11.85 Lacs

Kamrup - Assam

Tender For establishment of material testing laboratory under o/o the agm(c) design and projects aegcl kahilipara - civil works, compression testing machine (2000kn) with digital reading, automatic pace control with all attachment for testing concrete cube & bricks conforming to indian standards (is: 516, is: 14858) and can also be supplied as per british standards (bs: 1881), astm c-39 with calibration certificate. it should be typically calibrated to class 1 accuracy ( 1%); featuring a robust, fully welded loading unit and hardened, ground, and polished platens, often with a self-aligning upper platen; with display type as pc-controlled with software. it should have pace rate of full three-term pid feedback control with fully automated data acquisition, storage, and analysis. the operation should be fully automated, stress & strain controlled loading., aggregate impact test, crushing value apparatus with hammer weight of 13.75 kg 0.25 kg (or 14 kg 0.5 kg), height of free fall of 380 mm 5 mm, impact cup (mould) inner diameter of 102 mm 0.25 mm and impact cup depth of 50 mm 0.25 mm as per is 2386 (part iv), bs 812-112. automation grade often semi-automatic with a digital counter. display type digital for the blow counter; sometimes includes a digital gauge for other measurements. overall weight (approx.) should be of 45 kg to 60 kg (total machine mass). standards compliance conforms to international standards like is: 2386 (part iv), bs 812-112, etc. , sieves: (40, 20, 10, 4.75, 2.36, 1. 18) mm with lid and pan and (0.6, 0.3, 0. 15, 0.075) with lid and pan (all 200mm diameter size) metal : gi, weighing balance-30kg (accuracy-1gm)., weighing balance-5kg (accuracy-0.1gm)., hot air oven with double walled design, thick glass wool insulation to prevent heat loss, micro processor based auto tune pid digital temp controller cum indicators and 230 volt 50hz single phase ac supply, heavy duty stainless steel lock, indoor hinge and sample placement trays, temp range should be 50 degree c 250 degree c with temp accuracy 0.5 degree c. it should have digital led display of size 45 cm x 45 cm x 45 cm (inner)., cube mould (cast iron) of size 150mmx150mmx150mm, isi marked as per is:10086. weight of the mould will be about 13.5 kg, strictly as per bis specifications and within required tolerance., slump cone test apparatus-(isi marked)-with tamping rod (complete set ) as per is: 7320 and is: 1199 part 2, consisting of slump cone, base plate and graduated tamping rod - made of stainless steel., proctor test apparatus with all accessories as per is: 2720 part 8 and is: 10074(1982), complete with base plate and collar., measuring cylinder-borosilicate (1 complete set ) glass of sizes 100 ml, 250 ml, 500 ml and 1000 ml., field density test app-core cutter method ( complete set) complete with core cutter of 100 mm dia x 130 mm long with chromium plating, dolly for 100 mm dia core cutter, and rammer with steel rod as per is : 2720, rebound hammer digital (original/silver schmidt type n) with calibration certificate as per is 516 part 5, sec 4 with impact energy of 2.207 nm (1.63 ft-lbf), concrete strength range of 10 100 mpa (1450 14500 psi) and weight of 570 g (1.3 lb) with display as graphic lcd (e.g., 17x71 pixels) or analog/digital and battery life: >5000 impacts., ultrasonic pulse velocity test apparatus (proceq, acoustic control systems, vedantrik technologies) with calibration certificate and frequency range of 24 500 khz (nominal transducer); measurement resolution of 0.1 s (microseconds); pulse voltage ranging from 125 v to 500 v (adjustable); receiver gain of 1x, 10x, 100x, auto, up to 1000x (lab+ model); pulse shape as square wave; measurement modes as pulse velocity, surface velocity, e-modulus, compressive strength correlation, crack depth; memory which stores >500 measured values; display should be 79x21 mm passive matrix oled; connectivity through usb for pc connection; software: pundit link for analysis and export. standards compliance

CTN :45467743

18 Jun, 2026 NA

Hyderabad - Telangana

Tender For providing of custom bid for services - design, supply, installation, testing & commissioning lightning protection system with digital counter and earth pits at hyderabad unit

CTN :45404144

09 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for electronics and communication engineering department - supply of equipment for electronics and cmmunication engineering department, 8051 micro controller kit :specification : operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., temperaturemeasurementkitspecification : sensors:rtd (pt-100), thermocouple (fe-k/j-type), and/orthermistor (ntc). display: 3 digit led/lcd digital display(typically 200 mv fsd). temperature source: portable water kettle orheater block. signal conditioning: on-board circuitry foramplification, linearization, and cold junctioncompensation. test points: multiple 2 mm / 4 mm banana socketsfor monitoring input/output signals. power supply: 230 v ac, 50 hz, single-phase. accessories: glass thermometer, 10 k ntcthermistor probe, k-type thermocouple probe,patch cords and user manual., ask modulationanddemodulation kit:specification : message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz,amplitude 5 v. modulator type: switching modulator using analogswitch / transistor switching ic. demodulator: envelope detector and lpf. comparator: lm311 based. supply voltage (board): +12 v, +5 v dc. supply current: 100 ma minimum. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., dth trainer kit:specification :power supply: 200 v to 240 v ac, 50 hz.dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter): input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency:tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m.controls: channel selection. volume control.fault simulation: five built-in simulated faults for troubleshootingexperiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption.pcb size: 15" 12" with multicolour section-wise blockdiagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna.additional features: dth subscription connection withdoordarshanfree channels. free-to-air channel demonstration., fpga trainer kit:specification : must use industry-standard mid-range fpgadevice usb-jtag programmable, compatible withvivado ise (webpack). power supply: 5 v dc through usb or externaladapter. on-board peripherals: leds, switches, pushbuttons, 7-segment display,clock source, gpio /pmod expansion ports, uart, vga / hdmi, usbuartbridge, usb cable. user manual.

Central Government/Public Sector

CTN :45380439

11 Jun, 2026 NA

Burnpur - West Bengal

Tender For supply of gear box assy,3xmi80272.5 or d10.9.0-ma2 , diverter switch,3xmi80272.5 or d10.9.0-ma2 , transition resistance for lf transformer , dm digital counter for 3 x m i 802 , oil surge relay,rs-2001 , snap action switch,ma-2 , tap position indicator assy , slip ring current assy,3xmi802725 or d1090 , moving contact assy,3xmi80272.5 or d10.9.0 , selector stick assy,3xmi80272.5 or d10.9.0 , head cover o ring of oltc , bottom flange o ring of oltc , top drive unit assembly of oltc , oil surge relay of oltc , selector switch assy

CTN :45379134

10 Jun, 2026 NA

Arakandanallur - Tamil Nadu

Tender For for electrical and communication engineering department lab equipments are required as per new syllabus - upgradation of labarotariesece department, 8051 micro controller kit operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., single phase induction motor1 hp, 230 v ac, 1500 rpm with loading arrangement 1 no.voltmeter: (0 300) v ac, 96 96 mm with input terminals 1 no.ammeter: (0 10) a ac, 96 96 mm with input terminals 1 no.wattmeter: 2 kw, 96 96 mm with input terminals 1 no.power factor meter: 96 96 mm with input terminals 1 no.auto transformer: 0 300 v, 1 variac 1 no.mcb: 2-pole, 40 a / 230 v ac 1 no.digital rpm indicator with proximity sensor 1 no.aluminium brake drum: 230 mm diameter 1 no.spring balance: (0 25) kg 02 nos.circuit diagram printed on front panel with instruments and connecting terminals.motor and loading arrangement mounted on rigidchannel frame with anti-vibration mounting pads, m12 1.5 bolt & nut, 85 mm dia 4 nos.mild steel powder-coated electrical panel tablesetup., auto transformerinput: 230 240 v ac, 50 hz.output: variable (0 270) v ac.rating: 1 kva.insulation class: class f / class h.construction: copper winding with carbon brush arrangement.mounting: bench-top / panel type.protection: suitable fuse / overload protection., dth trainer kitpower supply: 200 v to 240 v ac, 50 hz. dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter): input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency:tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m. controls: channel selection. volume control. fault simulation: five built-in simulated faults for troubleshooting experiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption. pcb size: 15" 12" with multicolour section-wise block diagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna. additional features: dth subscription connection with doordarshanfree channels., sim reader trainer kitpower supply: operates on 230 v ac 10%, 50 hz mains supply. built-in regulated smps power supply. operating dc supply: 5 v / 12 v with overload and short-circuit protection.sim card interface: supports gsm sim cards compatible with 2g / 3g / 4g / 5g networks. sim card read/write interface. supports sim card initialization, authentication, and communication functions. compatible with standard 6-pin / 8-pin sim card sockets.communication interface: usb 2.0 interface for pc communication. rs-232 serial communication interface. uart communication facility for embedded system interfacing.sim operating parameters: selectable sim clock frequencies: 3.579 mhz 7.159 mhz 14.318 mhz sim supply voltage selection facility. sim reset and activation control. supported protocols and standards: gsm etsi 07.07 and etsi 07.05 at command support. iso/iec 7816 smart card communication support. sim communication command monitoring facility. hardware features: on-board sim card socket. led indication for: power status sim detection reset activity data transmission/r

CTN :45343672

11 Jun, 2026 NA

Madurai - Tamil Nadu

Tender For purchase of electronics and communication engineering practices (equipment) - equipments for electronics and communication engineering practices:, 8051 micro controller kit operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., embedded trainer kit (using lpc2148) cpu -lpc2148, core -16/32 bit arm7tdmi-s speed -max 60 mhz, flash -512kb, ram (on-chip) 40kb, 46 general purpose i/opins, usb2.0 one 10bit a/d converterwith 14 analog inputs, one 10bit d/a converter, six pwm &watchdog two uarts (16c550), two i2c (400kb/s), two spi eight bit digital output, eight bit digital input,16x2 characters lcd and 4x4 matrixkeypad one potentiometer for giving analog input, relay & buzzer interface i2c devices: rtc, eeprom and seven segment display, on board stepper motordriver lm35 temperature sensor, one rs 232 lines are terminated at 9 pin d type connector and usb interface board has inbuilt power supply and mounted in sturdy cabinet accessories usb cable with utility software to download programs from pc to target board power cord, user manual, ask modulation and demodulation kit message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz, amplitude 5 v. carrier signal: sine wave, frequency 200 khz, amplitude 5 v. modulator type: switching modulator using analog switch / transistor switching ic. demodulator: envelope detector and lpf. comparator: lm311 based. supply voltage (board): +12 v, +5 v dc. supply current: 100 ma minimum. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., dth trainer kitpower supply: 200 v to 240 v ac, 50 hz.dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter):input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency: tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m.controls: channel selection. volume control.fault simulation: five built-in simulated faults for troubleshooting experiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption.pcb size: 15" 12" with multicolour section-wise block diagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna.additional features: dth subscription connection with doordarshanfree channels. free-to-air channel demonstration.

Central Government/Public Sector

CTN :45292423

06 Jun, 2026 NA

Khorda - Odisha

Tender For tender for supply of supplying , installing , testing and commissioning approved make microprocessor based single (01) loop , networkable addressable fire alarm control panel , supplying , installing , testing and commissioning approved make digital audio amplifier. , supplying , installing , testing and commissioning approved make remote paging station for zone selection , supplying , installing , testing and commissioning approved make modbus interface gateway , the mimic annunciator for the fire alarm control panels (facp). , supplying , installing , testing and commissioning approved make addressable multi-criteria photo-thermal detector , supply , installation , testing and commissioning addressable self-test multi-criteria photo-thermal detector , supplying , installing , testing and commissioning approved make addressable manual call point , supplying , installing , testing and commissioning approved make addressable control module for sounders , supplying , installing , testing and commissioning approved make addressable relay module for ahu , access control , lifts , staircase pressurization , fire suppression & other third party outputs , supplying , installing , testing and commissioning approved make isolator module for isolating short / dewired / loose circuits with automatic resetting arrangement , supplying , installing , testing and commissioning approved make response indicator , supplying , installing , testing and commissioning of hooter cum strobe with in-built lithiumion battery , supplying , installing , testing and commissioning approved make 2w multi-tap wall mount speakers , supplying , installing , testing and commissioning of approved make auto dialer which supports gsm and pstn both , supply and laying of 2 c x 1.5 sq.mm. armoured cu multi-stranded twisted shielded frls copper cable , red in colour. , camc for 4 years after expiry of one year warranty of addressable fire detection system

Digital Counter Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

corporations/Associations/Others

Central Government/Public Sector

Central Government/Public Sector